SAMEBIKE 20LVXD30 Display User Manual

Introduction

This manual provides essential instructions for the proper installation, operation, and maintenance of your SAMEBIKE 20LVXD30 Display. Please read this manual thoroughly before using the display to ensure safe and efficient operation. Retain this manual for future reference.

Safety Information

Always prioritize safety when operating your electric bicycle. The display is an integral part of your e-bike's control system. Adhere to the following safety guidelines:

• Helmet Use: Always wear a certified helmet when riding your electric bicycle.
• Read Bicycle Manual: This display manual complements your electric bicycle's main owner's manual. Always read and understand the complete bicycle manual for critical safety information before riding.
• Local Regulations: Be aware of and comply with all local traffic laws and regulations regarding electric bicycle use.
• Environmental Conditions: Avoid exposing the display to extreme temperatures, heavy rain, or direct sunlight for prolonged periods.
• Professional Installation: If you are unsure about any installation or connection steps, consult a qualified bicycle technician.

Setup

The SAMEBIKE 20LVXD30 Display is designed for straightforward installation on compatible electric bicycles.

1. Mounting: Securely attach the display bracket to the center of your bicycle's handlebar. Ensure it is positioned for optimal visibility and accessibility while riding.
2. Cable Connection: Carefully connect the display's cable to the corresponding port on your electric bicycle's wiring harness. Ensure the connection is firm and properly seated to prevent accidental disconnection or water ingress.
3. Cable Management: Route the display cable neatly along the handlebar and frame, securing it with cable ties to prevent interference with steering or other components.
4. Initial Power-On: After installation, power on your electric bicycle. The display should illuminate and show initial readings.

Operating the Display

The 20LVXD30 Display provides real-time information and control over your electric bicycle's functions.

Display Overview

The main screen provides a clear overview of key riding data:

• Battery Level: Indicated by a battery icon and percentage (e.g., 90%).
• Current Power Output: Shows the instantaneous power being used (e.g., 682 W).
• Current Speed: Displays your current riding speed (e.g., 25.5 km/h).
• Trip Distance: Shows the distance covered during the current ride (e.g., 20.5 km/h, likely indicating trip distance in km).
• PAS Level: Indicates the current Pedal Assist System level (e.g., 1). This controls the amount of motor assistance.
• Time: Displays the current time (e.g., 19:45).

Basic Functions

• Power On/Off: Typically, a long press on a designated button (not visible in image, but standard) will power the display on or off.
• Adjusting PAS Level: Use the '+' and '-' buttons (if present, common design) to cycle through the Pedal Assist System levels. Higher levels provide more motor assistance.
• Changing Display Modes: Short presses on a mode button (if present) may cycle through different information displays, such as Odometer, Max Speed, Average Speed, etc.

Settings

Accessing the settings menu usually involves a specific button combination or a long press on a mode button. Within the settings, you may be able to:

• Set time and date.
• Change units (e.g., km/h to mph).
• Reset trip data.
• Adjust backlight brightness.
• Configure wheel size (if not automatically detected by the e-bike system).

Refer to your electric bicycle's main manual for detailed instructions on accessing and adjusting specific display settings, as these can vary.

Maintenance

Proper maintenance ensures the longevity and optimal performance of your SAMEBIKE 20LVXD30 Display.

• Cleaning: Use a soft, damp cloth to gently wipe the display screen and casing. Avoid abrasive cleaners, solvents, or direct water spray, which can damage the electronics.
• Protection: While the display is designed to be weather-resistant, avoid prolonged exposure to heavy rain or direct water submersion. Consider using a protective cover when parking outdoors for extended periods.
• Cable Inspection: Periodically check all cables and connections for signs of wear, fraying, or loose connections. Ensure they are securely fastened.
• Impact Avoidance: Protect the display from physical impacts, which can cause internal damage or screen cracks.

Troubleshooting

If you encounter issues with your 20LVXD30 Display, try the following troubleshooting steps:

• Display Not Turning On:
  • Ensure the electric bicycle's main power is on.
  • Check all cable connections to the display and the main wiring harness for looseness.
  • Verify the e-bike battery has sufficient charge.
• Incorrect Speed/Distance Readings:
  • Check the speed sensor and magnet on your bicycle wheel for proper alignment and cleanliness.
  • Ensure the wheel size setting in the display's menu (if adjustable) matches your bicycle's wheel size.
• PAS Not Functioning:
  • Verify the PAS level is set above 0 on the display.
  • Check the pedal sensor for any obstructions or damage.
• Error Codes: If an error code appears on the display, consult your electric bicycle's main manual or contact SAMEBIKE customer support with the specific code for assistance.

Specifications

Warranty and Support

The SAMEBIKE 20LVXD30 Display comes with a 12-month warranty from the date of purchase, covering manufacturing defects. This warranty does not cover damage caused by misuse, accidents, unauthorized modifications, or normal wear and tear.

For technical support, warranty claims, or further assistance, please contact SAMEBIKE customer service through their official website or your point of purchase. Please have your product model and purchase information ready when contacting support.