1. Introduction
Thank you for choosing the IKT Self Cleaning Bottom Load Water Cooler Dispenser with Ice Maker. This appliance provides convenient access to hot, cold, and room temperature water, along with the added benefit of an integrated ice maker. Designed for ease of use and maintenance, it features a bottom-loading water bottle system, a child safety lock for hot water, and an automatic self-cleaning function.
Please read this manual thoroughly before operation to ensure proper use, optimal performance, and safety.
2. Safety Information
To prevent injury to yourself and others, or damage to the appliance, please observe the following safety precautions:
- Always place the dispenser on a flat, stable surface away from direct sunlight and heat sources.
- Ensure the power cord is not pinched or damaged. Plug into a grounded electrical outlet.
- Do not operate the dispenser without a water bottle installed.
- Keep children away from the hot water dispenser. The child safety lock feature must always be engaged when not in use.
- Do not immerse the appliance, cord, or plug in water or other liquids.
- Unplug the dispenser before cleaning or performing any maintenance.
- This appliance is for indoor use only.
- Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection.
3. Setup and Installation
- Unpacking: Carefully remove the dispenser from its packaging. Retain packaging for future transport if needed.
- Placement: Position the dispenser on a level, sturdy floor surface. Allow at least 10 cm (4 inches) clearance from walls for proper ventilation.
- Initial Standby: After placing, allow the unit to stand upright for at least 24 hours before plugging it in. This allows refrigerants to settle.
- Power Connection: Plug the power cord into a grounded 120V AC outlet.
- Water Bottle Installation (Bottom Load):
- Open the lower cabinet door.
- Remove the cap from a standard 3 or 5-gallon water bottle.
- Insert the water probe into the bottle opening.
- Slide the bottle into the cabinet and close the door. The dispenser will automatically draw water.
- Initial Flushing: Before first use, dispense and discard at least 1 liter of water from each tap (hot, cold, room temperature) to flush the system.
Image: The IKT water cooler dispenser showing its dimensions and the bottom-loading compartment for a 3 or 5-gallon water bottle.
4. Operating Instructions
4.1 Control Panel Overview
Image: Close-up of the control panel showing LED indicators for "Making ice", "Child lock", "Lack of water", "ON/OFF", "Hot water", "Fresh water", "Cold water", "Ice volume", and "Energy saving". It also highlights the child safety lock feature.
The control panel features intuitive buttons and LED indicators to manage the dispenser's functions. Indicators illuminate to show the status of water heating, chilling, ice making, and when the water bottle is empty.
4.2 Dispensing Water
- Cold Water: Press the cold water button and push the lever to dispense chilled water.
- Room Temperature Water: Press the room temperature water button and push the lever to dispense ambient water.
- Hot Water (Child Safety Lock): To dispense hot water, first press and hold the child safety lock button, then press the hot water button and push the lever. This two-step process prevents accidental hot water dispensing.
Image: The IKT water cooler dispenser illustrating its capability to dispense hot, cold, and room temperature water, as well as ice cubes.
4.3 Ice Making Function
The dispenser includes a built-in ice maker that produces bullet-shaped ice cubes. It can produce up to 22 lbs of ice daily, with each cycle yielding 9 pieces of ice in approximately 7 minutes. The internal storage can hold up to 0.88 lbs of ice.
Important: The dispenser does not keep ice frozen. Ice will melt if not used promptly.
Image: Visual representation of the ice making capabilities, highlighting 22 lbs/24H daily capacity, 7 minutes fast ice making, and 9 bullet-shaped ice cubes per cycle. A note indicates that ice is not kept frozen.
4.4 Energy Saving (ECO) Mode
To activate the energy-saving mode, press the ECO button on the control panel. When ECO mode is active, the machine will automatically stop heating water during nighttime hours to conserve energy.
5. Maintenance
5.1 Self-Cleaning Function
The dispenser features an automatic self-cleaning function to maintain hygiene and water quality. This process utilizes a UV lamp located in the cold water container.
- Ensure a water bottle is installed.
- Press and hold the ice-making button for 3 seconds to activate the self-cleaning function.
- The indicator light will blink, and the power light will remain on during the cleaning cycle.
- The machine will automatically shut off after approximately 10 minutes.
Image: Diagram illustrating the UV-infused cleaning technology within the water cooler, showing how it reduces contaminants and improves water taste.
Image: An internal view of the water cooler dispenser, highlighting the UV lamp component responsible for disinfection.
5.2 Drip Tray Cleaning
The removable drip tray should be emptied and cleaned regularly to prevent overflow and maintain hygiene. Simply slide it out, empty any collected water, wash with mild soap and water, rinse thoroughly, and reinsert.
5.3 Exterior Cleaning
Wipe the exterior surfaces of the dispenser with a soft, damp cloth. Do not use abrasive cleaners or solvents.
6. Troubleshooting
Before contacting customer support, please refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No water dispensing | Empty water bottle; water probe not properly inserted; airlock in system. | Replace water bottle; ensure probe is fully inserted; dispense water from all taps to release air. |
| Water not hot/cold | Dispenser not plugged in; heating/cooling switches off; insufficient time for heating/cooling. | Ensure unit is plugged in and power is on; check if hot/cold functions are activated; allow 15-30 minutes for water to reach desired temperature. |
| Ice maker not producing ice | No water in reservoir; ice maker function off; ambient temperature too high. | Ensure water bottle is full; activate ice making function; ensure proper ventilation around the unit. |
| Water leakage | Water bottle cap not sealed properly; drain plug loose; damaged water line. | Check water bottle for proper seal; ensure drain plug is secure; contact customer support if water line is suspected to be damaged. |
| Unusual noise | Compressor operation (normal); unit not level; loose components. | Ensure unit is on a level surface; if noise persists or is excessive, contact customer support. |
7. Specifications
| Brand | IKT |
| Model | IKT Self Cleaning Bottom Load Water Cooler Dispenser with Ice Maker |
| Colour | Glossy Black |
| Product Dimensions (L x W x H) | 41.91 x 30.99 x 103.38 cm (16.5 x 12.2 x 40.7 inches) |
| Water Bottle Capacity | 3-5 Gallons |
| Material | Stainless Steel (tank) |
| Ice Making Capacity | Up to 22 lbs per 24 hours |
| Ice Storage Capacity | 0.88 lbs |
| Ice Production Time | Approx. 7 minutes per cycle (9 pieces) |
| Installation Type | Freestanding |
| Power Source | Corded Electric |
8. Warranty and Support
For warranty information or technical support, please refer to the documentation included with your purchase or contact IKT customer service directly. Please have your model number and purchase date available when contacting support.
Contact information for IKT customer support can typically be found on the manufacturer's website or on the product packaging.
