Polibi Full Size Upholstered Platform Bed with Storage, Desk, Charging Station & Trundle

Introduction

This manual provides detailed instructions for the assembly, operation, and maintenance of your Polibi Full Size Upholstered Platform Bed. Please read all instructions carefully before assembly and use to ensure safe and proper functionality of the product.

Safety Information

WARNING: Failure to follow these safety instructions could result in serious injury or damage to the product.

• Keep all assembly hardware out of reach of children.
• Ensure all bolts and screws are securely tightened before use. Periodically check and re-tighten as necessary.
• Do not exceed the maximum weight capacity: 600 lbs for the main bed, 250 lbs for the trundle.
• Use only on a flat, level surface.
• Do not stand or jump on the bed.
• Exercise caution when extending or retracting the trundle bed to avoid pinching.
• Ensure electrical connections for the charging station are properly installed and not overloaded. Disconnect power before cleaning or if any damage is observed.

Package Contents

Verify that all components are present before beginning assembly. If any parts are missing or damaged, contact Polibi customer support.

• Upholstered Headboard and Side Rails
• Bed Slats and Support Legs
• Trundle Bed Frame and Slats
• Integrated Desk and Storage Shelves
• Charging Station Unit (USB ports and outlets)
• Assembly Hardware (screws, bolts, Allen wrench)
• Instruction Manual

Setup and Assembly

Assembly typically requires two adults. Please follow the steps below in sequence.

Step 1: Unpack and Identify Components

Carefully remove all parts from the packaging. Lay them out on a clean, soft surface to prevent scratches. Refer to the parts list in your included manual to identify each component.

Image 1: Overview of the Polibi Full Size Upholstered Platform Bed, showcasing the main bed, integrated desk, storage shelves, and charging station.

Step 2: Assemble the Main Bed Frame

Connect the headboard, footboard, and side rails using the provided hardware. Ensure all connections are snug but do not overtighten until all parts are aligned.

Image 2: The main bed frame structure with wooden slats in place, ready for mattress placement.

Step 3: Install Bed Slats

Evenly space and secure the wooden bed slats across the frame. This provides support for your mattress. Ensure all slats are firmly attached to prevent movement.

Step 4: Assemble the Integrated Desk and Storage

Attach the desk and storage shelf components to the main bed frame as indicated in the detailed assembly diagram. These sections are designed to integrate seamlessly with the bed's structure.

Image 3: Detailed view of the integrated desk, storage shelves, and the built-in charging station with USB ports and power outlets.

Step 5: Install the Charging Station

Carefully insert the charging station unit into its designated slot on the desk/storage component. Ensure it is flush and secure. Connect the power cord to a wall outlet after the bed is fully assembled and positioned.

Step 6: Assemble the Trundle Bed

Assemble the trundle bed frame and install its slats. The trundle is designed to slide underneath the main bed. Ensure the wheels are properly attached for smooth operation.

Image 4: The Polibi bed with the trundle frame visible, showing how it slides out from underneath the main bed.

Step 7: Final Tightening and Placement

Once all components are assembled, go back and securely tighten all bolts and screws. Position the bed in its desired location. Plug in the charging station.

Image 5: Dimensional diagram illustrating the overall length (88.5"), width (66.5"), and height (29.5") of the Polibi bed.

Operating Instructions

Using the Trundle Bed

To extend the trundle bed, gently pull the handle located on the front panel of the trundle. The trundle will roll out smoothly on its wheels. To retract, push the trundle back underneath the main bed until it is fully concealed.

Image 6: The Polibi bed with the trundle fully extended, demonstrating its functionality as an additional sleeping space.

Using the Charging Station

Once the bed is assembled and the charging station is plugged into a wall outlet, you can use the two standard AC outlets and two USB ports to power or charge your electronic devices. Ensure devices are compatible with the provided power output.

Utilizing the Desk and Storage Shelves

The integrated desk provides a convenient surface for laptops, books, or other items. The storage shelves offer space for organizing personal belongings, books, or decorative items. Distribute weight evenly on shelves.

Maintenance

• Cleaning: For the upholstered fabric, gently spot clean with a damp cloth and mild detergent. Avoid harsh chemicals. For wooden or MDF surfaces, wipe with a dry or slightly damp cloth.
• Hardware Check: Periodically inspect all bolts and screws to ensure they remain tight. Re-tighten as needed to maintain stability.
• Trundle Mechanism: Keep the trundle wheels and tracks free of debris to ensure smooth operation.
• Electrical Components: Ensure the charging station is kept dry. Do not attempt to repair damaged electrical components; contact a qualified technician or customer support.

Troubleshooting

Specifications

• Brand: Polibi
• Model: B0FM3XGX96
• Size: Full
• Product Dimensions (L x W x H): 88.5" x 66.5" x 29.5"
• Material: Pine Wood + MDF, Upholstered (Velvet Fabric, High-Density Foam)
• Weight Capacity (Main Bed): 600 lbs
• Weight Capacity (Trundle): 250 lbs
• Special Features: Integrated Charging Station (2 AC outlets, 2 USB ports), Storage Shelves, Pull-out Trundle Bed, Desk
• Assembly Required: Yes

Warranty and Support

For warranty information, missing parts, or technical assistance, please contact Polibi customer support. Keep your purchase receipt and model number (B0FM3XGX96) handy for faster service.

Polibi Customer Support: Refer to the contact information provided with your purchase or visit the official Polibi website.