Braun Shave Head Attachment Instruction Manual

Introduction

This manual provides instructions for the proper installation, use, and maintenance of your Braun Shave Head Attachment. This attachment is designed to enhance the functionality of compatible Braun trimmers, offering a close shave experience.

Image: The Braun Shave Head Attachment, designed for various Braun trimmer models.

Compatibility

The Braun Shave Head Attachment is compatible with a wide range of Braun trimmer types. Please ensure your trimmer model is listed below to guarantee proper fit and function.

Compatible Trimmer Types:

• 5513, 5514, 5515, 5516, 5517, 5518
• 5541, 5542, 5544
• 5806, 5807, 5808
• BT7420, BT7421, BT7440, BT7441
• AIO7410, AIO7420, AIO7440, AIO7530, AIO7535
• MGK7410, MGK7420, MGK7421, MGK7440, MGK7450, MGK7460, MGK7461, MGK7470, MGK7490, MGK7491
• AIO7540, AIO7545, AIO7560, AIO7565, AIO7580, AIO7585
• BT 9420, BT 9421, BT 9440, BT 9441

To verify your trimmer's type number, refer to the markings on the trimmer body, usually located near the charging port or on the back of the device.

Installation

1. Remove Existing Attachment: Ensure the trimmer is turned off. Gently pull the existing trimming comb or attachment head upwards and away from the trimmer body. It should detach with a firm but gentle pull.
2. Clean Trimmer Head Area: Before attaching the new shave head, ensure the trimmer's head connection area is clean and free of hair or debris.
3. Attach Shave Head: Align the Braun Shave Head Attachment with the trimmer body. Press it down firmly until you hear a click, indicating it is securely fastened.
4. Verify Attachment: Gently tug on the shave head to ensure it is securely attached and does not wobble.

Refer to the video in the Compatibility section for a visual guide on detaching and attaching heads.

Operating Instructions

1. Preparation: Ensure your skin is clean and dry for optimal results.
2. Power On: Turn on your Braun trimmer.
3. Shaving Technique: Hold the trimmer with the shave head flat against your skin. Move the trimmer in short, gentle strokes against the direction of hair growth.
4. Rinsing: For models designed for wet use, the shave head can be rinsed under running water during or after use to clear hair clippings.
5. Power Off: After use, turn off the trimmer.

Maintenance

• Cleaning: After each use, remove the shave head attachment and tap out any loose hairs. For waterproof models, rinse the head under warm running water. Allow it to air dry completely before reattaching or storing.
• Lubrication: Periodically, apply a drop of light machine oil (such as sewing machine oil or specific shaver oil) to the cutting blades to maintain optimal performance and longevity.
• Storage: Store the shave head attachment in a clean, dry place, away from direct sunlight and extreme temperatures.
• Replacement: Shave heads are wear parts and should be replaced approximately every 18 months, or sooner if you notice reduced performance or discomfort.

Troubleshooting

• Attachment Does Not Fit: Double-check the compatibility list and your trimmer's type number. Ensure the attachment is aligned correctly before pressing it onto the trimmer body.
• Poor Shaving Performance:
  • Ensure the shave head is clean and free of hair buildup.
  • Apply a small amount of lubricant to the blades.
  • If performance does not improve, the shave head may need to be replaced due to wear.
• Irritation During Use:
  • Ensure the shave head is clean.
  • Replace the shave head if it is old or damaged, as dull blades can cause irritation.
  • Use gentle pressure and shave against the grain of hair growth.

Specifications

Warranty and Support

For specific warranty information regarding your Braun Shave Head Attachment, please refer to the documentation included with your original Braun trimmer or visit the official Braun website. For further support or inquiries, contact Braun customer service.

Braun Official Website: www.braun.com