Instruction Manual

1. Product Overview

This replacement parts kit is designed for Shark Navigator Robot Vacuum models RV2110, RV2120AE, and AV2110S. It includes essential components to maintain your robot vacuum's cleaning performance.

Package Contents:

• 2 Main Brushes
• 4 HEPA Filters
• 3 Filter Mesh
• 6 Side Brushes
• 1 Cleaning Brush

Image: Complete set of replacement parts, including main brushes, filters, filter mesh, and side brushes.

2. Installation Guide

2.1 Main Brush Installation

The main brush is crucial for deep cleaning. Replace it when wear is visible or cleaning performance decreases.

1. Turn off your robot vacuum and place it on a flat surface with the bottom facing up.
2. Locate the brush guard cover, usually secured by tabs or screws.
3. Open or remove the brush guard cover.
4. Lift out the old main brush.
5. Insert the new main brush, ensuring the ends align with the slots in the vacuum.
6. Close or re-secure the brush guard cover.

Image: A main brush, showing its rolling brush top joint and microfiber bristles.

Image: Close-up details of the main brush, highlighting the rolling brush top joint, premier quality microfiber, and ease of assembly.

2.2 HEPA Filter and Filter Mesh Installation

Filters capture fine dust and allergens. Regular replacement ensures optimal air quality and suction power.

1. Open the dust bin compartment on your robot vacuum.
2. Remove the dust bin.
3. Locate the filter assembly within the dust bin.
4. Remove the old HEPA filter and filter mesh.
5. Insert the new filter mesh first, followed by the new HEPA filter, ensuring they fit snugly.
6. Reinstall the dust bin into the vacuum until it clicks into place.

Image: Two HEPA filters, designed for high-efficiency air filtration.

Image: Close-up details of the high-efficiency filter, showing its high-density design and environmentally friendly materials.

2.3 Side Brush Installation

Side brushes sweep debris from edges and corners into the vacuum's path.

1. Turn off your robot vacuum and place it on a flat surface with the bottom facing up.
2. Locate the side brushes. They are typically held in place by a single screw.
3. Use a screwdriver to remove the screw holding the old side brush.
4. Carefully pull off the old side brush.
5. Align the new side brush with the post and push it down firmly.
6. Secure the new side brush with the screw.

Image: Two side brushes with three arms each, designed to sweep debris.

Image: Close-up details of the side brush, emphasizing its perfect fitting, dense bristles, and detachable design.

3. Maintenance and Replacement Schedule

Regular maintenance of your robot vacuum's parts ensures optimal performance and extends the life of your device.

• Main Brush: Inspect weekly. Clean hair and debris. Replace every 6-12 months, or sooner if visibly worn or damaged.
• HEPA Filters & Filter Mesh: Clean weekly by tapping out debris. Replace every 2-3 months, or more frequently if you have pets or allergies.
• Side Brushes: Inspect weekly for tangled hair or damage. Clean as needed. Replace every 3-6 months, or if bristles are bent or missing.
• Cleaning Brush: Use the included cleaning brush to remove hair and debris from the main brush and other hard-to-reach areas.

4. Troubleshooting Common Issues

• Reduced Suction: Check and replace HEPA filters and filter mesh. Ensure the dust bin is empty and properly seated.
• Brush Not Spinning: Inspect the main brush and side brushes for tangled hair or debris. Remove any obstructions. Ensure brushes are correctly installed.
• Unusual Noises: Check all brushes for foreign objects or excessive wear. Replace any damaged parts.
• Poor Edge Cleaning: Inspect and replace worn or bent side brushes.

5. Specifications

Image: Diagram showing the dimensions of the main brush, filters, filter mesh, and side brushes.

6. Warranty and Support

Information regarding specific warranty terms or direct support contacts is not provided with this product. For any issues or questions, please refer to the retailer where the product was purchased.