GIGABYTE UD750GM PG5 V2 ICE 750W Power Supply User Manual

1. Product Overview

The GIGABYTE UD750GM PG5 V2 ICE is a 750W fully modular power supply designed for high-performance computing systems. It features 80 Plus Gold certification for efficiency, ATX 3.1 compliance, and native PCIe 5.1 support, ensuring stable and reliable power delivery for modern components.

Key Features

• 750W Capacity with Single +12V Rail
• Supports PCIe Gen 5.1 graphics cards (16 Pin)
• Intel ATX 3.1 Certified
• 80 PLUS Gold Certified
• ATX Form Factor

Image 1.1: Top view of the GIGABYTE UD750GM PG5 V2 ICE Power Supply, highlighting the fan grille.

2. Safety Information

Please read and understand all safety instructions before installing or operating this power supply unit. Failure to follow these instructions may result in electric shock, fire, or damage to the product and connected components.

• Do not open the power supply casing. High voltage components are present inside, which can cause severe injury or death. There are no user-serviceable parts.
• Ensure the power supply is disconnected from the AC power outlet before installation, removal, or cleaning.
• Install the power supply in a well-ventilated area, away from heat sources, direct sunlight, and moisture.
• Use only the modular cables provided with this power supply. Using incompatible cables may cause damage.
• This product is designed for indoor use only.
• Professional installation is recommended.

Image 2.1: Rear panel of the power supply showing the AC input, power switch, and safety certification labels, including warning symbols.

3. Package Contents

Verify that all items are present in the package before proceeding with installation:

• GIGABYTE UD750GM PG5 V2 ICE Power Supply Unit
• Modular Cable Set (including 24-pin ATX, 8-pin CPU, 6+2-pin PCIe, 16-pin PCIe 5.1, SATA, and Molex cables)
• AC Power Cord
• Mounting Screws
• User Manual (this document)

4. Installation Guide

Follow these steps to properly install your GIGABYTE power supply into your computer system.

4.1. Prepare Your System

1. Turn off your computer and disconnect the AC power cord from the wall outlet.
2. Open your computer case. Refer to your case manufacturer's manual for specific instructions.
3. If replacing an existing power supply, disconnect all cables from the old PSU and remove it from the case.

4.2. Mount the Power Supply

1. Carefully place the new GIGABYTE power supply into the designated PSU bay in your computer case.
2. Align the screw holes on the power supply with those on the case.
3. Secure the power supply using the provided mounting screws.

4.3. Connect Modular Cables

Identify the necessary cables for your system components and connect them to the corresponding ports on the power supply. Ensure each cable is firmly seated.

Image 4.1: Modular cable connection panel. Labels indicate ports for M/B (Motherboard), CPU/PCI-E, Peripheral-IDE/SATA/Molex, and 12V-2x6 (PCIe 5.1).

• M/B (Motherboard): Connect the 24-pin ATX cable to the motherboard.
• CPU/PCI-E: Connect the 8-pin (4+4) CPU cable to the motherboard's CPU power connector. Connect 6+2-pin PCIe cables to your graphics card(s) as needed.
• 12V-2x6: Connect the 16-pin PCIe 5.1 cable directly to compatible graphics cards.
• Peripheral-IDE/SATA/Molex: Connect SATA power cables to storage drives (HDDs, SSDs) and optical drives. Use Molex cables for other peripherals if required.

4.4. Connect to Components

Route the connected modular cables neatly within your case and connect them to their respective components (motherboard, CPU, graphics card, storage drives, etc.). Ensure all connections are secure.

4.5. Connect AC Power

1. Ensure the power switch on the back of the power supply is in the 'OFF' (0) position.
2. Connect the AC power cord to the power supply's AC inlet.
3. Plug the other end of the AC power cord into a grounded wall outlet or surge protector.

5. Operation

Once installation is complete, you can power on your system.

5.1. Powering On/Off

1. Flip the power switch on the back of the power supply to the 'ON' (I) position.
2. Press the power button on your computer case.
3. To turn off the system, shut down your operating system normally. For a complete power cycle, flip the power switch on the PSU to 'OFF' (0) after system shutdown.

6. Maintenance

Proper maintenance helps ensure the longevity and optimal performance of your power supply.

6.1. Cleaning

• Periodically clean the exterior of the power supply and its fan grille to prevent dust buildup.
• Use compressed air to gently remove dust from the fan and vents.
• Always disconnect the AC power cord before cleaning.

6.2. Fan Check

Ensure the power supply fan is operating correctly. If you notice unusual noises or the fan is not spinning under load, consult the troubleshooting section or contact support.

7. Troubleshooting

If you encounter issues with your power supply, refer to the following common problems and solutions.

7.1. No Power

• Check AC Power: Ensure the AC power cord is securely connected to both the power supply and the wall outlet. Verify the wall outlet has power.
• PSU Switch: Confirm the power switch on the back of the PSU is in the 'ON' (I) position.
• Cable Connections: Double-check all modular cable connections, especially the 24-pin ATX and 8-pin CPU cables, are firmly seated.
• System Components: Disconnect non-essential components (e.g., extra drives, peripherals) to isolate if a faulty component is preventing the system from booting.

7.2. System Instability or Random Shutdowns

• Overload: Ensure your system's power requirements do not exceed the 750W capacity of the PSU.
• Ventilation: Check that the power supply and case have adequate airflow and are not obstructed by dust.
• Cable Integrity: Verify all power cables are in good condition and properly connected.
• Component Issues: Test other components (RAM, GPU) if possible, as instability may not always be PSU-related.

8. Specifications

Detailed technical specifications for the GIGABYTE UD750GM PG5 V2 ICE Power Supply.

9. Warranty and Support

9.1. Warranty Information

This GIGABYTE power supply is covered by a 10-year manufacturer's warranty. Please retain your proof of purchase for warranty claims. The warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, accident, modification, or improper installation.

9.2. Technical Support

For technical assistance, troubleshooting, or warranty inquiries, please visit the official GIGABYTE support website or contact their customer service.

GIGABYTE Official Store: https://www.amazon.com/stores/GIGABYTE/page/854232BB-540A-4979-BE5B-6F3F3A530F1E