1. Vehicle Compatibility
This Nixon Offroad Rear Bumper (Style A) is designed for:
- 2025 Dodge Ram 1500 Pickup Truck
- 2026 Dodge Ram 1500 Pickup Truck
Important Note: This bumper is not compatible with vehicles equipped with a camera connector or blind spot mid-range radar systems.

2. Included Parts
Verify all components are present before beginning installation:
- 1 x Rear Bumper Assembly
- 2 x D-Rings
- 2 x LED Pod Lights (4-inch)
- All necessary Mounting Accessories (bolts, nuts, washers, brackets)
3. Specifications
| Feature | Detail |
|---|---|
| Material | Q235A Steel |
| Weight | 85.99 LBS |
| Dimensions (L x W x H) | 77 x 17 x 13 inches |
| Exterior Finish | Textured Black Powder Coat |
| Installation Type | Bolt-On |
| Special Features | Integrated Side Steps, D-Ring Mounts (2 included), LED Pod Light Mounts (2 included), Parking Sensor Holes, License Plate Mounting Holes, Trailer Plug Mounting Holes, Spare Wheel Lock Cylinder Case Mounting Hole |
4. Installation Instructions
4.1 General Installation
The Nixon Offroad Rear Bumper is designed for a direct bolt-on installation. No cutting or drilling is required, as it utilizes existing factory holes on your vehicle. Ensure all mounting hardware is securely fastened according to the vehicle's specifications.
4.2 Key Features and Mounting Points
Familiarize yourself with the various features and mounting points of the bumper:

- Decorative Frames: Integrated into the bumper design.
- License Lamp Mounting Hole: Provides a dedicated space for your license plate light.
- Spare Wheel Lock Cylinder Case Mounting Hole: Allows for the installation of a spare wheel lock cylinder.
- Non-Slip Stepped Platform: Located on the sides for improved access to the truck bed.
- Parking Sensor Mounting Holes: Designed to accommodate factory parking sensors.
- Mounting Holes for Trailer Plug: Pre-drilled for easy installation of a trailer wiring harness.
- D-Ring Mounting Brackets: Integrated for recovery points.
4.3 LED Pod Light Installation
The bumper includes mounting brackets for 3-inch or 4-inch pod lights. Two 4-inch LED pod lights are supplied with the bumper. Install these lights into the designated brackets on each side of the bumper and connect them to your vehicle's electrical system as per standard automotive lighting practices.


4.4 D-Ring Installation
Two D-rings are included. Attach these to the integrated shackle mounting brackets on the bumper. Ensure they are securely fastened for safe use as recovery points.

4.5 Parking Sensor Integration
The bumper features pre-drilled holes for factory parking sensors. Carefully transfer your existing parking sensors from your original bumper to these designated locations. Ensure proper seating and connection to maintain functionality of your vehicle's parking assist system.

5. Operation and Features
5.1 Side Steps
The bumper includes integrated side steps on both ends, providing a non-slip platform for easier access to your truck bed. Use these steps for safe entry and exit when loading or unloading cargo.

5.2 LED Pod Lights
The integrated LED pod lights enhance rear visibility and provide additional illumination for tasks such as backing up, working in low-light conditions, or off-road use. Operate these lights via your vehicle's auxiliary light switch or a custom wiring harness.
5.3 D-Rings
The D-rings serve as robust recovery points for off-road situations or vehicle extraction. Always use appropriate recovery straps and follow safe recovery procedures. Ensure D-rings are securely fastened before any recovery operation.
5.4 Parking Sensors
If your vehicle is equipped with factory parking sensors and they have been correctly installed into the bumper's designated holes, they will function as intended, assisting with parking maneuvers by detecting obstacles behind the vehicle.
5.5 Trailer Plug and License Plate
The bumper provides dedicated mounting locations for your trailer plug and license plate, ensuring proper integration and compliance with road regulations.
6. Maintenance
The Nixon Offroad Rear Bumper features a textured black powder coat finish designed for corrosion and rust resistance. To maintain its appearance and integrity:
- Regularly clean the bumper with mild soap and water to remove dirt, salt, and other debris.
- Avoid using abrasive cleaners or harsh chemicals that could damage the powder coat finish.
- Inspect all mounting hardware periodically to ensure it remains tight and secure. Re-tighten as necessary.
- Check the condition of the LED pod lights and their wiring for any signs of damage or corrosion.
6.1 Customization (DIY)
The bumper features honeycomb decorative mesh panels that allow for DIY customization. You may choose to paint these panels a different color to match your vehicle or personal preference. Ensure proper preparation and painting techniques are used to maintain durability.

7. Troubleshooting
If you encounter any issues during installation or operation, consider the following:
- Loose Fit: Ensure all mounting bolts are tightened to the manufacturer's recommended torque specifications.
- LED Pod Lights Not Working: Check wiring connections, fuses, and ensure the lights are properly grounded.
- Parking Sensors Malfunctioning: Verify sensors are correctly seated in their mounting holes and their electrical connections are secure. Ensure no debris is obstructing the sensor's field of view.
- Incompatibility Issues: Re-verify your vehicle's model year and trim against the compatibility information. Remember, this bumper is not compatible with camera connectors or blind spot radar systems.
For persistent issues or concerns not addressed here, please refer to the Support section.
8. Warranty Information
Nixon Offroad provides the following warranty coverage for this product:
- 30-Day Refund or Replacement: For issues related to incompatibility or defects upon receipt.
- 12-Month Limited Warranty: Covers product malfunction from the date of purchase.
Please retain your proof of purchase for warranty claims.
9. Customer Support
For technical assistance, warranty claims, or any questions regarding your Nixon Offroad Rear Bumper, please contact the seller or manufacturer directly through the platform where the purchase was made. Provide your product model number (205A-01-NRM06B101-BX) and purchase details for efficient support.