Tedeligo Wireless Dimmer Switch 3-in-1 with Remote Control

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Tedeligo Wireless Dimmer Switch. This 3-in-1 system includes a wireless remote control transmitter and three dimmer control modules, designed for 220-250V AC circuits. It allows for remote brightness control of LED and halogen lamps ranging from 10W to 150W, and is compatible with existing wall dimmer switches without requiring Wi-Fi connectivity.

2. Safety Information

• Electrical Hazard: Installation must be performed by a qualified electrician or in accordance with local electrical codes. Ensure power is disconnected at the circuit breaker before installation.
• Voltage: This device operates on 220-250V AC. Do not connect to other voltage systems.
• Load Capacity: Do not exceed the maximum load of 150W for LED and halogen lamps. Overloading can cause damage or fire.
• Compatibility: Only use with compatible LED and halogen lamps. Refer to the compatibility section for details.
• Environment: The dimmer module has an IP00 rating, meaning it offers no protection against dust or water ingress. Install in a dry, protected environment.
• Maintenance: Do not attempt to repair or modify the device. Contact support for assistance.

3. Package Contents

Verify that all items are present in your package:

• 1 x Wireless Remote Control Transmitter (with base)
• 3 x Dimmer Control Modules
• 1 x Product Manual
• Connection Wires
• Double-sided Adhesive Tape
• Screw Accessories

4. Product Features

• Wireless Control: Control light brightness remotely without Wi-Fi.
• Dual Control Modes: Operate via the original wall switch (with reset button) or the wireless remote transmitter.
• Extended Control Range: Stable control distance of up to 30 meters indoors and 50 meters outdoors, effective even through walls.
• Flexible Control: Up to 20 wireless remote transmitters can control a single dimmer module. The remote features 5 independent channels (01-05) to control multiple dimmer modules without interference.
• Wide Compatibility: Suitable for 10-150W LED and halogen lamps.

5. Installation Guide

5.1 Wiring Diagram

Ensure power is OFF before proceeding with any wiring. Connect the dimmer module according to the diagram below. The module should be installed within a standard electrical box or a suitable enclosure.

5.2 Mounting the Dimmer Module

The compact design of the dimmer module allows it to be placed behind an existing wall switch or inside a ceiling rose. Use the provided double-sided adhesive tape or screw accessories for secure mounting.

5.3 Pairing the Remote Control

To pair the remote control with a dimmer module:

1. Ensure the dimmer module is powered on.
2. Press the pairing button on the dimmer module (usually a small button on the side or top, refer to the module itself for exact location). The indicator light on the module will blink.
3. Within 5 seconds, press any button on the remote control. The indicator light on the module will stop blinking, indicating successful pairing.
4. Repeat for additional dimmer modules if necessary, assigning each to a different channel on the remote if desired.

6. Operating Instructions

6.1 Using the Remote Control

The wireless remote control allows for convenient adjustment of light brightness.

• Power Button: Press to turn the light ON or OFF.
• Brightness Up/Down: Use the dedicated buttons to increase or decrease light intensity.
• Channel Selection: The remote has 5 channels (01-05). Use the channel selection button to cycle through channels and control different dimmer modules independently.

6.2 Using the Original Wall Switch

After installing the dimmer module, your existing wall switch (if it has a reset button) can also control the dimming function. A quick press will toggle ON/OFF, while a long press may initiate dimming, depending on the switch type.

6.3 Multi-Channel Control

The remote control's 5 channels allow you to manage up to 5 different dimmer modules or groups of modules independently. Simply select the desired channel (01-05) on the remote before adjusting the light.

7. Compatibility

This dimmer switch is designed for use with 10-150W LED and halogen lamps. It is compatible with various common bulb types as illustrated below.

8. Maintenance

• Cleaning: Wipe the remote control and dimmer module with a dry, soft cloth. Do not use liquid cleaners or solvents.
• Battery Replacement: The remote control uses a 12V battery. Replace it when the control range decreases or the remote becomes unresponsive. Ensure correct polarity when replacing.
• Environment: Keep the devices away from extreme temperatures, humidity, and direct sunlight.

9. Troubleshooting

10. Specifications

11. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact your retailer. Keep your proof of purchase for any warranty claims.