1. Introduction
The MicroTech Glucometer Kit is designed for convenient and accurate blood glucose monitoring. This manual provides essential information for the proper use, maintenance, and troubleshooting of your device to ensure reliable results and effective diabetes management.
The system requires a tiny 0.5µL blood sample and provides results in just 5 seconds. It features a wide Hematocrit (HCT) range of 10%-70%, making it suitable for a broad range of users, including infants, pregnant women, and individuals with specific health conditions. The meter can store up to 500 test results, offering 7/14/30/60/90-day average blood glucose values for easy tracking.
2. What's Included
Your MicroTech Glucometer Kit includes the following components:
- 1 x Gocheck2 Blood Glucose Monitor
- 10 x Blood Test Strips
- 10 x 30 gauge Lancets
- 1 x Lancing device
- 1 x Portable storage bag
- 1 x Meter User Guide
- 1 x Test Strip User Guide
Figure 2.1: Complete Blood Glucose Monitoring Kit Components.
3. Setup Instructions
3.1. Installing Batteries
The Gocheck2 Blood Glucose Monitor requires 2 CR2032 batteries (included). To install:
- Locate the battery compartment on the back of the meter.
- Open the battery cover.
- Insert the batteries according to the polarity indicators (+/-).
- Close the battery cover securely.
3.2. Preparing the Lancing Device
The lancing device is used to obtain a blood sample.
- Unscrew the cap of the lancing device.
- Insert a new lancet firmly into the lancet holder.
- Twist off the protective cap of the lancet.
- Replace the lancing device cap.
- Adjust the penetration depth by rotating the cap. Start with a shallower setting (e.g., 2-3) and adjust as needed for a sufficient blood sample.
- Pull back the cocking barrel until it clicks, indicating it is ready for use.
Figure 3.1: Initial setup steps for the MicroTech Glucometer Kit.
4. Operating Instructions
4.1. Performing a Blood Glucose Test
Follow these steps for an accurate blood glucose measurement:
- Prepare Your Hands: Wash your hands thoroughly with soap and warm water, then dry them completely.
- Insert Test Strip: Remove a test strip from its vial and immediately close the vial cap tightly. Insert the test strip into the test strip port of the meter. The meter will turn on automatically and display a blood drop symbol.
- Obtain Blood Sample: Use the prepared lancing device to prick the side of your fingertip. Gently squeeze your finger to form a small drop of blood (approximately 0.5µL).
- Apply Blood Sample: Touch the tip of the test strip to the blood drop. The strip will draw the blood into the sample area. Do not apply blood to the top of the strip.
- Read Result: The meter will begin counting down. Your blood glucose result will appear on the display in 5 seconds.
- Eject Test Strip: Press the strip ejection button to safely discard the used test strip without touching it, preventing cross-infection.
- Dispose of Lancet: Carefully remove the used lancet from the lancing device and dispose of it in a sharps container.
Figure 4.1: Rapid result display on the MicroTech Glucometer.
Figure 4.2: Only a small 0.5µL blood sample is required.
Figure 4.3: Automatic strip ejection for convenient and hygienic disposal.
4.2. Understanding Display and Alerts
The meter's display shows the date, time, test result, and measurement units (mg/dL). It also features personalized high and low blood sugar alerts, which can be set according to your doctor's advice.
Figure 4.4: High and low blood sugar alerts.
Figure 4.5: GoCheck2 Blood Glucose Monitor product description and parts.
5. Maintenance and Storage
5.1. Cleaning the Meter
Wipe the meter exterior with a soft, damp cloth. Do not immerse the meter in water or use harsh cleaning agents.
5.2. Test Strip Storage
Proper storage of test strips is crucial for accuracy:
- Store test strips in their original sealed container.
- Keep them away from heat, moisture, and direct sunlight.
- Do not refrigerate.
- Discard any remaining test strips 6 months after opening the vial, or by the expiration date printed on the vial, whichever comes first.
Figure 5.1: Test strip validity periods.
6. Troubleshooting
If you encounter issues with your MicroTech Glucometer Kit, refer to the following common questions and answers:
| Question | Answer |
|---|---|
| Why do different test results from brand A to brand B? | Each manufacturer's blood glucose meter has different settings, so the same blood sample may yield different results. |
| If various error letters such as "E-1" are displayed on your blood glucose meter, what should you do? | At the end of the instruction manual, we have provided explanations for each type of error screen display. You can find the answers by matching them one by one. |
| Why were results different after measuring blood sugar twice in a row? |
|
Figure 6.1: Common troubleshooting questions and solutions.
7. Specifications
| Feature | Detail |
|---|---|
| Model Name | Gocheck2 |
| Item Model Number | 10KIt |
| Operating Time | 5 Seconds |
| Blood Sample Volume | 0.5µL |
| Memory Storage | Up to 500 test results |
| Hematocrit (HCT) Range | 10% - 70% |
| Batteries | 2 CR2032 batteries (included) |
| Battery Cell Composition | Lithium Metal |
| Test Strip Validity (Opened) | 180 days (6 months) |
| Certifications | FDA, CE, GMP, ISO 15197:2015 |
| Package Dimensions | 7.2 x 6.65 x 1.93 inches |
| Item Weight | 8.15 ounces |
8. Warranty and Support
MicroTech provides an exclusive Lifetime Warranty and Technical Support for your Glucometer Kit. For any questions, concerns, or technical assistance, please refer to the contact information provided in your product packaging or visit the official MicroTech website.
