LifePro LumaGlow 2-in-1 Reading & Red Light Therapy Floor Lamp

1. Introduction

The LifePro LumaGlow is a versatile 2-in-1 floor lamp designed to provide both focused reading illumination and therapeutic red light. This device integrates 108 high-powered LEDs, offering 850nm Near Infrared (NIR) and 660nm Red Light for therapy, alongside 4000K white light for reading. This manual provides essential information for the safe and effective operation of your LumaGlow lamp.

Image 1.1: The LifePro LumaGlow lamp demonstrating its dual functionality for red light therapy and reading.

2. Safety Information

Please read all safety instructions before using the LifePro LumaGlow lamp.

• Electrical Safety: Ensure the power cord is not damaged and is plugged into a suitable electrical outlet. Do not operate with wet hands or in damp environments.
• Eye Protection: While red light therapy is generally safe, prolonged direct exposure to the LEDs may cause discomfort. Eye protection is recommended during red light therapy sessions, especially for sensitive individuals.
• Heat: The lamp head may become warm during extended use. Avoid direct contact with the LEDs when the lamp is on.
• Medical Disclaimer: This product is not intended to diagnose, treat, cure, or prevent any disease. Consult with a healthcare professional before starting any new therapy, especially if you have pre-existing medical conditions or are pregnant.
• Children and Pets: Keep the lamp out of reach of children and pets to prevent accidental damage or injury.

3. Package Contents

Verify that all components are present in the package:

• LumaGlow Lamp Head with Gooseneck
• Lamp Pole Sections (typically 2-3 sections)
• Lamp Base
• Remote Control
• Power Adapter
• User Manual (this document)

Image 3.1: All components included in the LifePro LumaGlow package.

4. Setup and Assembly

Follow these steps to assemble your LumaGlow lamp:

1. Attach Pole Sections: Carefully screw the lamp pole sections together clockwise until they form a single, sturdy pole. Ensure the internal wiring is not pinched.
2. Connect to Base: Screw the assembled lamp pole into the lamp base clockwise until it is securely tightened. The base is weighted for stability.
3. Attach Lamp Head: Connect the gooseneck of the lamp head to the top of the assembled pole. Ensure the connection is firm.
4. Power Connection: Insert the power adapter into the designated port on the lamp pole, then plug the adapter into a standard electrical outlet.
5. Remote Control: Insert batteries (not included) into the remote control if necessary.

Your LumaGlow lamp is now ready for operation.

5. Operating Instructions

The LumaGlow lamp can be operated using the integrated controls on the lamp pole or the wireless remote control.

5.1. Power On/Off

• Press the Power Button (usually marked with a circle and vertical line) on the lamp pole or remote to turn the lamp on or off.

5.2. Switching Modes (Red Light Therapy / Reading Lamp)

• Press the Red Light Button (marked 'R' or a red light icon) to activate the Red Light Therapy mode. This mode combines 660nm Red Light and 850nm Near Infrared Light.
• Press the White Light Button (marked 'W' or a white light icon) to activate the Reading Lamp mode (4000K white light).

Image 5.1: The LumaGlow lamp in both red light therapy and reading lamp configurations.

5.3. Adjusting Brightness/Intensity

• Use the Brightness Up and Brightness Down buttons (often marked with sun icons or '+' / '-') on the lamp pole or remote to adjust the light intensity for both modes.

Image 5.2: The flexible design and remote control allow for customized light positioning and intensity.

5.4. Timer Function

• The lamp features a built-in timer for convenience. Consult the remote control or lamp pole for specific timer settings (e.g., 15, 30, 60 minutes). The lamp will automatically shut off after the selected duration.

5.5. Gooseneck Adjustment

• The flexible gooseneck allows for 360° adjustment of the lamp head. Position the light to target specific areas for therapy or to optimize reading illumination.

6. Red Light Therapy Usage Guidelines

For optimal results and safety, adhere to the following guidelines when using the red light therapy mode:

• Session Duration: Start with 10-15 minute sessions per target area. You may gradually increase to 20-30 minutes as tolerated.
• Frequency: Use 3-5 times per week, or as recommended by a healthcare professional.
• Distance: Position the lamp head approximately 6-12 inches (15-30 cm) from the skin for effective penetration.
• Target Areas: The flexible gooseneck allows you to direct the light to various body parts, including face, neck, shoulders, back, and joints.
• Eye Protection: Always use the provided eye protection or close your eyes during facial treatments to avoid direct exposure to the bright LEDs.

Image 6.1: Proper use of the LumaGlow lamp for red light therapy, including recommended eye protection.

7. Reading Lamp Usage Guidelines

The 4000K white light mode provides comfortable illumination for reading and other tasks:

• Optimal Brightness: Adjust the brightness to a level that is comfortable for your eyes and the ambient lighting conditions.
• Positioning: Use the flexible gooseneck to direct the light precisely where needed, minimizing glare and shadows.
• Versatility: This mode is suitable for reading, working, hobbies, or as general ambient lighting.

Image 7.1: The LumaGlow lamp providing clear, focused white light for reading.

8. Maintenance

• Cleaning: Disconnect the power before cleaning. Wipe the lamp's exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Storage: When not in use for extended periods, store the lamp in a cool, dry place. You may disassemble it for more compact storage if desired.
• LED Longevity: The LEDs are designed for long-term use and do not require replacement.

9. Troubleshooting

If you encounter issues not listed here, please contact LifePro customer support for assistance.

10. Specifications

• Model: LP-LMGLW-BLK
• Brand: LifePro
• Product Dimensions: 8.66 x 8.66 x 75.59 inches
• Item Weight: 6.06 Pounds
• Lamp Type: LED
• Total LEDs: 108 (36 Near Infrared, 36 Red, 36 White)
• Wavelengths: 850nm (Near Infrared), 660nm (Red Light), 4000K (White Light)
• Material: Alloy Steel
• Finish Type: Matte

Image 10.1: Detailed breakdown of the 108 LEDs within the LumaGlow lamp head.

11. Warranty and Support

LifePro products are designed for durability and performance. For information regarding your product's warranty, please refer to the warranty card included with your purchase or visit the official LifePro website.

LifePro offers a supportive online community and customer service for assistance with setup, usage tips, and troubleshooting. You can find more resources and contact information via the official LifePro website or by searching for "LifePro" online.

Online Resources: LifePro Official Store