1. Introduction
Thank you for choosing the Rollerhouse Crown and Drive Adapter Bushing Fittings. This product is designed to replace worn or damaged crown and drive assemblies in your Coolaroo Shade Motor system, specifically for 28mm (1-1/8 inch) shade tubes. By replacing these critical components, you can restore smooth operation, eliminate motor slippage, and extend the life of your existing shade system without needing to replace the entire unit.
Image 1: Rollerhouse Crown and Drive Adapter Bushing Fittings.
2. Compatibility
These Crown and Drive Adapter Bushing Fittings are specifically engineered for:
- Shade Tube Diameter: 1-1/8 inches (28mm)
- Motor Type: Coolaroo Shade Motors
Ensure your shade tube matches the specified diameter for a guaranteed fit and optimal performance.
Image 2: Visual confirmation of fit for 28mm tubes, including the custom adapter sleeve.
3. Components Included
Each package contains the following components:
- 1 x Rubberized Crown Adapter
- 1 x Drive Adapter
These components are made of durable plastic, designed for UV and abrasion resistance.
Image 3: Detailed dimensions of the crown and drive adapters.
4. Setup and Installation
Follow these steps to replace your existing crown and drive adapters:
- Safety First: Ensure the shade motor is completely disconnected from its power source before beginning any installation or repair.
- Remove Shade: Carefully remove the shade fabric from the tube, if necessary, to access the motor and tube ends.
- Access Motor: Gently slide the shade tube off the motor assembly to expose the existing crown and drive components.
- Remove Old Components: Detach the old crown and drive adapters from the motor shaft. Note their orientation for reference.
- Install New Drive Adapter: Slide the new drive adapter onto the motor shaft, ensuring it seats firmly and correctly. The drive adapter typically has internal splines that engage with the motor shaft.
- Install New Crown Adapter: Place the new crown adapter onto the motor shaft, adjacent to the drive adapter. The crown adapter supports the motor within the shade tube.
- Reassemble Shade Tube: Carefully slide the 28mm shade tube back over the motor assembly, ensuring the new crown and drive adapters fit snugly inside the tube. The custom adapter sleeve included helps ensure a seamless fit.
- Test Operation: Reconnect the motor to its power source and perform a test run to ensure the shade operates smoothly without slippage or unusual noises.
If you encounter any resistance or difficulty during installation, double-check the compatibility and ensure all components are aligned correctly.
5. Operating
Once the Rollerhouse Crown and Drive Adapter Bushing Fittings are correctly installed, your Coolaroo Shade Motor will operate as intended. The new fittings are designed to eliminate common issues such as motor slippage and vibration, providing a stable and reliable connection between the motor and the shade tube. Operate your shade using its standard controls.
6. Maintenance
These plastic components are designed for durability and require minimal maintenance:
- Cleaning: If necessary, gently wipe the adapters with a soft, damp cloth. Avoid using harsh chemical cleaners, as they may degrade the plastic material.
- Inspection: Periodically inspect the crown and drive adapters for any signs of wear, cracks, or damage. While designed to be robust, extreme conditions or prolonged use may eventually lead to wear.
- Environmental Conditions: The plastic material is UV and abrasion resistant, suitable for typical indoor and outdoor shade environments.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor still slips or vibrates after installation. | Incorrect installation; tube not fully seated; motor shaft damage; incorrect tube size. | Ensure adapters are fully seated and aligned. Verify shade tube is 28mm. Inspect motor shaft for damage. |
| Difficulty sliding shade tube over adapters. | Misalignment of adapters; debris inside tube; incorrect tube size. | Check alignment of crown and drive. Clear any obstructions. Confirm shade tube is 28mm. |
| Adapters appear loose within the shade tube. | Incorrect tube size; adapter not fully expanded (if applicable). | Verify shade tube is 28mm. Ensure the custom adapter sleeve is used for a snug fit. |
8. Specifications
- Model Number: QD1528+HG1528-C
- Compatibility: 1-1/8 inch (28mm) Shade Tubes, Coolaroo Shade Motors
- Material: Durable Plastic (UV and abrasion resistant)
- Product Dimensions: Approximately 1 x 0.6 x 0.6 inches
- Item Weight: Approximately 3.52 ounces
- Included Components: Crown Adapter, Drive Adapter
9. Warranty and Support
Rollerhouse stands behind the quality of its products. While specific warranty details are not provided in this manual, please refer to your purchase documentation or contact Rollerhouse customer support for information regarding warranty coverage and assistance.
For technical support, installation queries, or any other assistance, please visit the official Rollerhouse website or contact their customer service department. Contact information can typically be found on the product packaging or the brand's online store.