FOTING 15-inch Pressure Washer Surface Cleaner Attachment

Important Safety Information

Please read and understand all safety warnings and instructions before operating the FOTING Pressure Washer Surface Cleaner Attachment. Failure to follow these instructions may result in serious injury or property damage.

• Always wear appropriate personal protective equipment (PPE), including eye protection, gloves, and sturdy footwear, during operation.
• Ensure all connections are secure and leak-free before starting the pressure washer.
• Never direct the high-pressure spray at people, pets, or electrical equipment.
• Keep children and bystanders away from the operating area.
• Do not exceed the maximum pressure of 4000 PSI or maximum water temperature of 140°F (60°C).
• Always refer to your pressure washer's instruction manual for additional safety guidelines and operating procedures.
• Disconnect the attachment from the pressure washer and release all pressure before performing any maintenance or cleaning.

Package Contents

Verify that all items listed below are included in your package:

• 1 x FOTING 15-inch Pressure Washer Surface Cleaner Attachment
• 1 x 16-inch Extension Wand
• 2 x Replaceable Nozzles
• 4 x Replacement O-Rings
• 1 x Cleaning Needle
• 1 x Waterproof Tape

Figure 2: Package Contents - FOTING 15-inch Surface Cleaner, 16-inch Extension Wand, Nozzles, O-Rings, Cleaning Needle, and Waterproof Tape.

Specifications

Setup

Follow these steps to properly set up your FOTING Surface Cleaner Attachment:

1. Inspect Components: Before assembly, ensure all parts listed in the 'Package Contents' section are present and free from damage.
2. Connect Extension Wand: Attach the 16-inch extension wand to your pressure washer gun. The wand features a 1/4-inch quick-connect fitting. Push the collar back on your pressure washer gun's quick-connect, insert the wand, and release the collar to secure it. Pull on the wand to confirm a secure connection.
3. Attach Surface Cleaner: Connect the FOTING 15-inch Surface Cleaner to the other end of the extension wand. Use the same quick-connect method: pull back the collar on the wand, insert the surface cleaner's connector, and release the collar. Verify the connection is secure.
4. Check Nozzles: Ensure the two spray nozzles located on the underside of the surface cleaner are securely tightened. These are pre-installed but should be checked.
5. Water Supply: Connect your pressure washer to a suitable water supply according to its manufacturer's instructions.

Figure 3: Surface Cleaner connected to a pressure washer.

Operation

The FOTING Surface Cleaner is designed for efficient cleaning of large flat surfaces. Follow these steps for optimal performance:

1. Prepare Area: Clear the area to be cleaned of any loose debris, furniture, or obstacles.
2. Start Pressure Washer: Turn on your water supply and start your pressure washer according to its operating instructions.
3. Begin Cleaning: Position the surface cleaner flat on the surface you intend to clean. Hold the pressure washer gun firmly with both hands.
4. Engage Trigger: Squeeze the trigger on your pressure washer gun. The high-pressure water will activate the internal spray bar, causing it to rotate 360 degrees and clean a 15-inch wide path. The integrated splash-proof skirt will help minimize overspray.
5. Move Steadily: Move the surface cleaner slowly and consistently across the surface. Overlap each pass slightly to ensure thorough and even cleaning, preventing streaks. Avoid lifting the cleaner off the surface during operation.
6. Release Trigger: Release the trigger to stop the water flow when you need to pause, reposition, or finish cleaning.
7. Rinse Surface: After cleaning with the surface cleaner, it is often beneficial to rinse the entire area with a standard pressure washer nozzle to wash away loosened dirt and debris.
8. Shut Down: Follow your pressure washer's instructions for proper shutdown, including releasing residual pressure.

Figure 4: High Performance Features - 360° Spray Rotation and Splash-Free Skirt.

Figure 5: Multi-Application - Effective on various hard surfaces.

Maintenance

Regular maintenance ensures the longevity and optimal performance of your FOTING Surface Cleaner Attachment.

• Nozzle Cleaning: If you notice reduced pressure or an inconsistent spray pattern, the nozzles may be partially clogged. Disconnect the surface cleaner from the pressure washer. Use the provided cleaning needle to carefully clear any debris from the nozzle openings. Rinse the nozzles with clean water.
• O-Ring Inspection and Replacement: Periodically inspect the O-rings on all quick-connect fittings for signs of wear, cracks, or damage. Worn O-rings can cause leaks. Replace damaged O-rings with the included spare O-rings to maintain a watertight seal.
• General Cleaning: After each use, rinse the entire surface cleaner thoroughly with clean water to remove any dirt, grime, or chemical residues. This prevents buildup and corrosion.
• Storage: Store the surface cleaner in a clean, dry, and protected area. Avoid storing it in direct sunlight or in locations where temperatures can drop below freezing, as this can damage components.

Troubleshooting

Warranty and Support

The FOTING 15-inch Pressure Washer Surface Cleaner Attachment is backed by a THREE-YEAR after-sale service.

If you encounter any problems or have questions regarding the product, please contact FOTING customer support. Refer to your purchase documentation or the FOTING official website for contact information.