GRACO 26D360 TrueCoat 360 Cordless Connect Drill Sprayer User Manual

1. Introduction

This manual provides instructions for the safe and effective use of the Graco TrueCoat 360 Cordless Connect Drill Sprayer, model 26D360. This tool is designed for DIY enthusiasts to apply paint and stain for projects up to 2 gallons, offering cordless operation when connected to a compatible drill/driver or impact driver.

Figure 1: Graco TrueCoat 360 Cordless Connect Drill Sprayer (Model 26D360) with an attached cordless drill.

Figure 2: The TrueCoat 360 Cordless Connect is part of the DIY Series, suitable for light projects up to 2 gallons in size.

Figure 3: The sprayer is ideal for various DIY projects including interior walls, furniture, cabinets, doors, trim, and fences.

2. Important Safety Information

WARNING: Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov.

Always read and understand all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. Keep all warnings and instructions for future reference.

General Safety Precautions:

• Wear appropriate personal protective equipment (PPE) including eye protection, gloves, and a respirator.
• Ensure adequate ventilation in the work area.
• Keep children and bystanders away while operating the sprayer.
• Do not spray flammable liquids near open flames or ignition sources.
• Always disconnect the drill/power source before cleaning, adjusting, or performing maintenance.
• Refer to the material manufacturer's safety data sheet (SDS) for specific handling and disposal instructions.

3. Package Contents

The Graco TrueCoat 360 Cordless Connect Drill Sprayer package includes the following items:

• 1 x Graco TrueCoat 360 Cordless Connect Drill Sprayer unit
• 1 x Paint Tip (wide)
• 1 x Stain Tip (wide)
• 1 x Inlet Filter
• 2 x 32 ounce FlexLiner bags
• 1 x Easy Fill Funnel and Strainer
• 1 x Seal Lube
• Quick Start-Up Guide
• Instruction Manual (this document)

4. Setup

4.1 Attaching a Cordless Drill

The TrueCoat 360 Cordless Connect is designed to be powered by your own cordless drill/driver or impact driver. Ensure your drill has a minimum speed of 1400 RPM for optimal performance.

Figure 4: The sprayer is compatible with 1/4" drill/drivers and 1/4" impact drivers. A minimum of 1400 RPM is required.

Figure 5: Choose a drill/driver for slower speeds and more control, or an impact driver for larger projects and faster pace.

1. Align the sprayer's drive shaft with the chuck of your cordless drill.
2. Securely tighten the drill chuck around the drive shaft.
3. Ensure the connection is firm to prevent slippage during operation.

4.2 Preparing Paint or Stain

The TrueCoat 360 is designed to spray unthinned paint or stain. However, it is crucial to always consult the paint or stain manufacturer's instructions and recommendations for thinning, especially for thicker materials. Some paints, despite general claims, may require thinning for optimal performance and to prevent damage to the sprayer. Use the Easy Fill Funnel and Strainer System to strain your material, preventing clogs.

4.3 Filling the FlexLiner Bag

1. Insert a new 32-ounce FlexLiner bag into the paint cup.
2. Pour your prepared paint or stain into the FlexLiner bag. Do not overfill.
3. Attach the paint cup assembly to the sprayer unit, ensuring it is securely fastened.

4.4 Priming the Sprayer

Priming removes air from the system and prepares the sprayer for use.

1. Ensure the spray tip is removed.
2. Set the sprayer to the "Prime" setting.
3. Point the sprayer into a waste container.
4. Activate your drill to run the sprayer until a steady stream of material flows from the tip opening, indicating all air has been purged.
5. Release the drill trigger and set the sprayer to the "Spray" setting.
6. Install the desired paint or stain tip.

5. Operation

5.1 Spraying Techniques

Maintain a consistent distance and speed for an even finish. Overlap each pass by approximately 50%.

Figure 6: The sprayer allows for spraying in any direction, including upside down, thanks to VacuValve technology. Ensure your drill meets the minimum 1400 RPM requirement.

Figure 7: Using a drill/driver allows for a slower pace and more control, ideal for detailed work like spraying cabinet doors.

VacuValve Technology

The exclusive VacuValve technology, combined with the FlexLiner system, allows you to spray in any direction, even upside down, without losing prime or experiencing sputtering. This is particularly useful for ceilings, undersides of furniture, or other awkward angles.

TrueAirless Experience

• TRUEQUALITY: Professional-grade technology in a user-friendly design.
• TRUESPEED: Designed for quick one-pass coverage.
• TRUECONTROL: Provides unmatched control with minimal overspray.

6. Maintenance and Cleaning

Proper cleaning after each use is essential to ensure the longevity and performance of your Graco TrueCoat 360 sprayer.

1. Empty FlexLiner: Remove the FlexLiner bag and dispose of any remaining material according to local regulations.
2. Rinse: Fill a new FlexLiner bag with appropriate cleaning solution (water for latex, mineral spirits for oil-based paints).
3. Flush System: Attach the filled FlexLiner, set the sprayer to "Prime," and run the drill until the cleaning solution runs clear.
4. Clean Tip: Remove the spray tip and guard. Clean them thoroughly with a brush and cleaning solution.
5. External Cleaning: Wipe down the exterior of the sprayer with a damp cloth.
6. Seal Lube: Apply a small amount of the provided Seal Lube to the pump's piston after cleaning to maintain its condition.
7. Storage: Store the sprayer in a clean, dry place.

7. Troubleshooting

8. Specifications

9. Warranty and Support

For warranty information, technical support, or replacement parts, please contact Graco customer service directly. Refer to the Quick Start-Up Guide or Graco's official website for the most current contact details.

Important Note: Always ensure you are using genuine Graco replacement parts to maintain product performance and warranty validity.