Furitek SlideVolt Combo Royal Instruction Manual

1. Introduction and Overview

The Furitek SlideVolt Combo Royal is an advanced electronics upgrade designed for 1/10 scale RC drift cars. This combo includes the SlideTech Sensored Electronic Speed Controller (ESC) in the Crimson Gold Edition and the Voltmaster 10.5T Sensored Brushless Motor. It provides precise throttle control, real-time tuning capabilities, and high-performance power delivery for both drifting and stock racing applications.

Image 1.1: The Furitek SlideVolt Combo Royal, featuring the SlideTech Sensored ESC and Voltmaster 10.5T Sensored Brushless Motor.

2. Safety Information

Warning: This product is not intended for use by children. Adult supervision is required during operation and maintenance.

• Always disconnect the battery from the ESC when not in use to prevent accidental operation and potential damage.
• Ensure all connections are secure before operating the RC vehicle. Loose connections can cause damage or malfunction.
• Avoid contact with water or moisture, as this can damage the electronic components.
• Operate the RC vehicle in open areas, away from people, pets, and obstacles.
• Do not modify the ESC or motor. Unauthorized modifications can lead to product failure and void the warranty.

3. What's in the Box

The Furitek SlideVolt Combo Royal package includes the following components:

• SlideTech Sensored Electronic Speed Controller (ESC)
• Voltmaster 10.5T Sensored Brushless Motor

4. Setup

Follow these steps to properly install and configure your SlideVolt Combo Royal:

1. Motor Installation: Securely mount the Voltmaster 10.5T Sensored Brushless Motor into your 1/10 RC drift car chassis. Ensure proper gear mesh between the motor pinion and spur gear.
2. ESC Mounting: Mount the SlideTech Sensored ESC in a location that allows for good airflow and easy access to connections. Use double-sided tape or screws as appropriate for your chassis.
3. Motor to ESC Connection: Connect the three motor phase wires (A, B, C) from the motor to the corresponding terminals on the ESC. Ensure the sensor cable from the motor is securely plugged into the sensor port on the ESC.
4. Receiver Connection: Plug the ESC's receiver cable into the throttle channel (usually Channel 2) of your RC receiver.
5. Battery Connection: Connect your battery to the ESC's battery input terminals. Ensure correct polarity (red to positive, black to negative).
6. Calibration: Power on your transmitter, then power on the ESC. Follow the ESC's calibration procedure (refer to the specific SlideTech ESC manual for detailed steps) to synchronize it with your transmitter's throttle input.
7. Initial Tuning: The SlideTech ESC features an OLED display and Bluetooth connectivity for real-time tuning. Use the integrated trackball and screen or download the Furitek app on your mobile device to access and adjust settings.

Image 4.1: The SlideTech Sensored ESC, showing its integrated OLED display for direct tuning.

5. Operating Instructions

Once the SlideVolt Combo Royal is installed and calibrated, you can begin operating your RC drift car:

• Power On: Turn on your RC transmitter first, then connect the battery to the ESC. The ESC will power on and indicate readiness.
• Throttle Control: The SlideTech ESC provides ultra-smooth throttle control. Gradually apply throttle to move the vehicle forward or backward.
• Real-time Tuning: Utilize the Bluetooth connectivity and the Furitek mobile app or the ESC's OLED display to make real-time adjustments to parameters such as throttle response, braking, drag brake, and motor timing. This allows for fine-tuning performance to suit different track conditions and driving styles.
• Advanced Features: Explore advanced settings like Turbo and Boost for increased power delivery, and the Rev Limiter for specific drift effects. Adjust these settings carefully to avoid damage to components.
• Power Off: Always disconnect the battery from the ESC first, then turn off your RC transmitter.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your SlideVolt Combo Royal:

• Cleaning: Keep the ESC and motor clean from dirt, dust, and debris. Use a soft brush or compressed air. Avoid using liquids directly on electronic components.
• Connection Checks: Periodically inspect all electrical connections (motor wires, sensor cable, battery connectors, receiver cable) for signs of wear, corrosion, or looseness. Secure any loose connections.
• Motor Inspection: The Voltmaster motor features forced air cooling and a CNC-machined 7075-T6 aluminum housing. Ensure the cooling vents are not obstructed. Check motor bearings for smooth operation.
• Firmware Updates: Check the Furitek website or app for any available firmware updates for your ESC. Keeping the firmware updated can improve performance and add new features.

Image 6.1: The Voltmaster 10.5T Sensored Brushless Motor, designed for consistent performance with forced air cooling.

7. Troubleshooting

If you encounter issues with your SlideVolt Combo Royal, refer to the following common troubleshooting steps:

• ESC Not Powering On:
  - Ensure the battery is fully charged and properly connected to the ESC with correct polarity.
  - Check all wiring connections between the ESC, motor, and receiver for looseness or damage.
  - Verify that the power switch on the ESC (if applicable) is in the 'ON' position.
• Motor Not Responding or Erratic Behavior:
  - Re-calibrate the ESC with your transmitter.
  - Check the sensor cable connection between the motor and ESC. A loose or damaged sensor cable can cause erratic operation in sensored motors.
  - Inspect motor wires for damage or short circuits.
  - Ensure the motor pinion and spur gear are not binding and have proper mesh.
• Overheating:
  - Check for proper gear ratio. An overly aggressive gear ratio can cause the motor and ESC to overheat.
  - Ensure adequate airflow around the ESC and motor. Remove any obstructions.
  - Verify that the motor's cooling vents are clear of debris.
  - Reduce aggressive settings like Turbo or Boost if overheating occurs frequently.
• Loss of Control/Interference:
  - Ensure your transmitter batteries are charged.
  - Check for external sources of radio interference.
  - Verify that the receiver and ESC are securely mounted and not experiencing excessive vibration.

For persistent issues, consult the Furitek mobile app for diagnostic information or contact Furitek customer support.

8. Specifications

9. Warranty Information

Specific warranty details for the Furitek SlideVolt Combo Royal are typically provided with the product packaging or available on the official Furitek website. Please retain your proof of purchase for any warranty claims. In general, warranties cover manufacturing defects under normal use conditions. Damage resulting from misuse, unauthorized modifications, or improper installation is usually not covered.

10. Support

For technical assistance, product inquiries, or warranty support, please refer to the following resources:

• Official Furitek Website: Visit the official Furitek website for the latest product information, FAQs, and support contact details.
• Retailer Support: Contact the retailer from whom you purchased the product for initial support or return/exchange inquiries.
• Online Resources: Search for community forums or online groups dedicated to Furitek products or RC drifting for peer-to-peer assistance.

You can also visit the Furitek Store on Amazon for additional product information and seller contact options.