Vlectro Extra Loud Wireless Doorbell User Manual - Model 5404017912731

1. Introduction

Thank you for choosing the Vlectro Extra Loud Wireless Doorbell. This system is designed to provide a reliable and easily audible notification for visitors, particularly beneficial for the elderly or individuals with hearing difficulties. This manual will guide you through the installation, operation, and maintenance of your new doorbell system.

2. Safety Information

• Keep the doorbell button and receiver away from direct sunlight, rain, and extreme temperatures.
• Do not attempt to open or repair the devices yourself. Refer all servicing to qualified personnel.
• Battery Safety: Ensure correct polarity when inserting batteries into the receiver. Do not mix old and new batteries, or different types of batteries. Dispose of used batteries responsibly according to local regulations.
• Keep small parts, such as batteries, out of reach of children to prevent choking hazards.

3. Package Contents

Please check that all items are present in your package:

• 1 x Vlectro Wireless Doorbell Button (Transmitter)
• 1 x Vlectro Wireless Doorbell Receiver
• Mounting Hardware (Screws and Wall Plugs)
• Adhesive Pad
• User Manual (this document)

Figure 1: Image showing the Vlectro Wireless Doorbell button and receiver. The button is a compact, black, water-resistant unit, and the receiver is a slightly larger black unit, typically placed indoors.

4. Setup and Installation

4.1 Installing the Receiver

1. Open the battery compartment on the back of the receiver.
2. Insert the required AAA batteries (not included), ensuring correct polarity (+/-).
3. Close the battery compartment.
4. Place the receiver in a central location within your home where the chime can be easily heard. The receiver is portable and does not require a power socket.

4.2 Installing the Doorbell Button (Transmitter)

The doorbell button can be installed using either the provided adhesive pad or screws.

Option A: Adhesive Mounting

1. Clean the desired mounting surface thoroughly to ensure it is dry and free of dust or grease.
2. Peel off one side of the protective film from the adhesive pad and attach it to the back of the doorbell button.
3. Peel off the other side of the protective film and firmly press the doorbell button onto the cleaned surface for at least 30 seconds.

Option B: Screw Mounting

1. Mark the desired drilling points on the wall using the doorbell button as a template.
2. Drill two holes at the marked positions.
3. Insert the wall plugs into the drilled holes.
4. Align the doorbell button with the holes and secure it with the provided screws.

Note: Ensure the doorbell button is installed in a location protected from heavy rain to prolong its lifespan, despite its water-resistant design.

5. Operating Instructions

5.1 Changing the Chime Melody

Your Vlectro doorbell offers 58 different chime melodies. To change the melody:

1. On the receiver, locate the "Music Selection" button (often indicated by a musical note icon).
2. Press this button repeatedly to cycle through the available melodies.
3. Once you hear your preferred melody, stop pressing the button. The receiver will automatically save this selection.

5.2 Adjusting Volume

The receiver has 4 adjustable volume levels, including a mute option, with a maximum output of 100dB.

1. On the receiver, locate the "Volume" button (often indicated by a speaker icon).
2. Press this button repeatedly to cycle through the volume levels (Level 1, Level 2, Level 3, Level 4, Mute).
3. Select the desired volume level.

5.3 Pairing (If Needed)

Your doorbell system should be pre-paired from the factory. If the doorbell button does not trigger the receiver, you may need to re-pair them:

1. On the receiver, press and hold the "Volume" button for approximately 5 seconds until you hear a "ding" sound or see an indicator light flash. This puts the receiver into pairing mode.
2. Within 10 seconds, press the doorbell button once.
3. The receiver should chime, indicating successful pairing. If not, repeat the process.

6. Maintenance

• Cleaning: Wipe the doorbell button and receiver with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Battery Replacement (Receiver): When the receiver's sound becomes weak or stops working, it's time to replace the AAA batteries. Follow the instructions in Section 4.1.
• Battery Replacement (Doorbell Button): The doorbell button typically uses a long-lasting coin cell battery (e.g., CR2032). If the button stops working, carefully open the button casing (refer to manufacturer's instructions if available, or gently pry open) and replace the battery, ensuring correct polarity.

7. Troubleshooting

8. Specifications

• Model: 5404017912731
• Brand: Vlectro
• Product Dimensions: 7.7 x 11.5 x 8.7 cm
• Colour: Black
• Included Components: Wireless Doorbell Button, Receiver
• Wireless Range: Up to 150 meters (open air)
• Sound Level: Up to 100dB
• Chime Melodies: 58 options
• Volume Levels: 4 levels, including mute
• Receiver Power: AAA Batteries (not included)
• Manufacturer: Confinity (NV)

9. Warranty and Support

For warranty information or technical support, please refer to the retailer where the product was purchased or visit the official Vlectro website. Please retain your proof of purchase for warranty claims.