TNICER T2 Motorcycle Intercom User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your TNICER T2 Motorcycle Intercom. The T2 intercom is designed to enhance your riding experience with advanced communication features, including Bluetooth 5.4 connectivity, multi-rider intercom capabilities, and high-fidelity audio. Please read this manual thoroughly before using the device to ensure proper function and safety.

2. Safety Information

• Always prioritize road safety. Do not operate the device in a manner that distracts you from riding.
• Ensure the device is securely mounted to your helmet before each use.
• Adjust volume levels to a comfortable setting that still allows you to hear ambient traffic sounds.
• Do not attempt to disassemble or modify the device, as this may void the warranty and pose safety risks.
• Keep the device away from extreme temperatures and direct sunlight.

3. Package Contents

Verify that all items listed below are included in your package:

• T2 Main Unit
• Hard Microphone
• Soft Microphone
• Base Plate
• Metal Clip
• 3M Adhesive Tapes
• Magic Tape (Velcro)
• USB Type-C Charging Cable
• Interchangeable Color Panels (3 colors: Black, White, Red)
• User Manual

Image: Contents of the TNICER T2 Intercom package, including the main unit, microphones, mounting accessories, charging cable, and interchangeable color panels.

4. Setup

4.1 Initial Charging

Before first use, fully charge the T2 intercom. Connect the included Type-C charging cable to the device and a 5V1A power source. Avoid using rapid charging adapters to prevent potential battery damage. The charging indicator will show the charging status.

Image: Illustration of the TNICER T2 intercom being charged via its Type-C port, highlighting the 900mAh battery capacity and charging times.

4.2 Mounting the Intercom

The T2 intercom can be mounted using either the metal clip or 3M adhesive tape. Choose the method most suitable for your helmet.

1. Attach the Base Plate: Secure the base plate to the side of your helmet using either the metal clip (slide it under the helmet shell) or the 3M adhesive tape (clean the surface thoroughly before applying).
2. Install the Main Unit: Slide the T2 main unit onto the attached base plate until it clicks into place.

4.3 Microphone and Speaker Installation

Select either the hard microphone (for clear voice pickup) or the soft microphone (for flexible placement and comfort).

Image: Two types of microphones for the TNICER T2 intercom: a hard boom microphone and a soft wired microphone, offering versatility for different helmet types and user preferences.

1. Speakers: Attach the speakers inside your helmet, aligning them with your ears. Use the provided Velcro pads for secure placement.
2. Microphone: Position the chosen microphone near your mouth. Connect the microphone and speaker cables to the appropriate ports on the T2 main unit. Ensure all connections are firm.

Image: The TNICER T2 intercom's detachable main unit for easy charging and the 3.5mm universal audio jack for connecting custom speakers or headphones.

5. Operating Instructions

5.1 Power On/Off

• Power On: Press and hold the Power button until the indicator light illuminates.
• Power Off: Press and hold the Power button until the indicator light turns off.

5.2 Bluetooth Pairing (Smartphone/GPS)

1. With the T2 powered off, press and hold the Power button for approximately 5 seconds until the red and blue LEDs flash alternately. This indicates pairing mode.
2. On your smartphone or GPS device, enable Bluetooth and search for available devices.
3. Select "TNICER T2" from the list. Once connected, the blue LED will flash slowly.

5.3 Intercom Communication (Group Pairing)

The T2 supports simultaneous communication for up to 6 riders with a range of up to 1km in open environments. It features one-touch automatic pairing.

Image: Illustration of six motorcycles connected via TNICER T2 intercoms, demonstrating the 1km communication range and group connectivity.

1. Ensure all T2 units are powered on.
2. On one T2 unit (the host), initiate pairing by following the instructions for your specific model (refer to the detailed pairing procedure for new vs. old T2 models in the feature bullet section if applicable).
3. Other T2 units will automatically connect. Once connected, the blue LED will flash slowly.
4. If a rider leaves the group range, their unit will automatically attempt to re-connect when back in range.

5.4 Music Sharing

The T2 supports music sharing for up to 6 riders simultaneously.

Image: Six riders on motorcycles, with musical notes indicating simultaneous music sharing through their TNICER T2 intercoms.

• Once paired with a smartphone, begin music playback.
• Initiate music sharing through the device's controls (refer to specific button functions in the quick start guide).
• Other paired T2 units will receive the shared audio.

5.5 FM Radio

The T2 includes an integrated FM radio tuner (76MHz-108MHz).

Image: A rider on a motorcycle with an overlay indicating FM radio reception at 88.5MHz, demonstrating the FM radio feature of the TNICER T2 intercom.

• Activate FM radio mode using the designated button (refer to the quick start guide).
• The device supports automatic station search and channel memory.
• Dynamic noise cancellation helps maintain clear reception.

5.6 Voice Assistant

Quickly activate your smartphone's voice assistant.

• Simultaneously press the Volume Up (+) and Volume Down (-) buttons to activate the voice assistant.

6. Maintenance

6.1 Cleaning

• Wipe the device with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Ensure the Type-C charging port is clean and dry before charging.

6.2 Battery Care

• Charge the device regularly, even if not in use, to maintain battery health.
• Avoid fully discharging the battery frequently.

6.3 Changing Color Panels

The T2 intercom features interchangeable color panels for personalization.

Image: The TNICER T2 intercom with three interchangeable color panels (red, white, black), demonstrating customization options.

• Gently detach the current color panel from the main unit.
• Align the desired new color panel and snap it into place. This process typically takes about 5 seconds and requires no tools.

7. Troubleshooting

If you encounter issues with your TNICER T2 intercom, refer to the following common solutions:

8. Specifications

Technical specifications for the TNICER T2 Motorcycle Intercom:

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the product packaging or visit the official TNICER website. Keep your purchase receipt as proof of purchase for warranty claims.