Introduction
This manual provides essential instructions for the safe installation, operation, and maintenance of your Shine Decor IP68 Waterproof LED Strip Light. This professional-grade LED strip is designed for underwater applications in pools, fountains, waterfalls, and architectural water features. Please read these instructions thoroughly before installation and retain them for future reference.
Safety Precautions
- Professional Installation Recommended: This product is intended for professional water feature projects. Installation requires advanced electrical and sealing knowledge. It is recommended for contractors and designers familiar with customized lighting systems.
- Disconnect Power: Always disconnect power to the installation area before handling any wiring or components.
- Do Not Cut: To maintain waterproof integrity, the LED strip must not be cut.
- Uncoil Before Use: Always uncoil the LED strip completely before connecting to power to prevent overheating.
- UL676 Standard: This product meets UL676 Standard for underwater safety. Ensure all connected accessories also meet relevant safety standards.
- Low Voltage: Operates on 24V low voltage. Ensure compatible power supply is used.
- Waterproof Components: Use only IP67 or IP68 rated waterproof junction boxes and power supplies for all connections in wet environments.
What's in the Box
The package includes:
- Shine Decor IP68 Waterproof LED Strip Light (Warm White, 6m/19.69ft)
- Light kit included (specific components may vary by variant, refer to product packaging for details)
Note: Power supply, controller, mounting hardware, and waterproof boxes are sold separately and must be sourced based on project specifications.
Setup and Installation
Follow these steps for proper installation. Ensure all power is disconnected before beginning.
1. Choosing the LED Driver (Power Supply)
Select a UL-listed, Class 2, IP67 waterproof 24V LED driver with sufficient wattage for your LED strip length. For this 6m/19.69ft strip, a 96W driver is suitable. Ensure the driver's output voltage matches the LED strip's requirement (24V DC).
Image: A 24V 96W waterproof LED driver, UL listed and Class 2 safe, suitable for powering the LED strip.
2. Connecting the Driver to a Waterproof Junction Box
Use an IP67 rated waterproof junction box (available in 2-way or 3-way configurations depending on your setup). Open the box by unscrewing the lid. Feed the driver's output cable through a screw cap and screw nut, then through an entry port of the junction box. Ensure about 5cm of cable protrudes inside the box. Secure the internal snap ring and tighten the screw cap and nut clockwise until fully sealed.
Video: Demonstrates how to connect the LED driver cable to a waterproof junction box, including threading the cable through the screw cap and nut, and securing the internal snap ring.
3. Connecting the LED Strip (Single Color) with Dimmer (Optional)
If using a dimmer, connect it between the power supply and the LED strip. Loosen the terminal screws on the dimmer's input side. Connect the red wire from the power supply to the V+ terminal and the black wire to the V- terminal. Tighten firmly. Then, feed the LED strip's cable through another screw cap and nut into the junction box. Loosen the output terminal screws on the dimmer. Connect the black wire from the LED strip to the V+ terminal and the white wire to the V- terminal. Tighten firmly. Ensure correct polarity (V+ to V+, V- to V-).
Image: Close-up of connecting the power supply wires to the input terminals of a single-color LED dimmer, highlighting polarity.
Image: Close-up of connecting the LED strip wires to the output terminals of a single-color LED dimmer, emphasizing correct polarity.
4. Connecting the LED Strip (RGB) with RGB Controller (Optional)
If using an RGB controller, connect it between the power supply and the RGB LED strip. Loosen the terminal screws on the controller's input side. Connect the red wire from the power supply to the V+ terminal and the black wire to the V- terminal. Tighten firmly. Then, feed the RGB LED strip's cable through another screw cap and nut into the junction box. Loosen the output terminal screws on the controller. Match the wire colors from the RGB strip to their corresponding labeled terminals on the controller (e.g., Red to R, Green to G, Blue to B, Black to V+). Insert each bare wire firmly and tighten all screws securely. Ensure no wires are loose.
Image: Close-up of connecting the power supply wires to the input terminals of an RGB LED controller, highlighting polarity.
Image: Close-up of connecting the RGB LED strip wires to the output terminals of an RGB LED controller, emphasizing correct color matching.
5. Sealing Unused Ports
For any unused entry ports on the waterproof junction box, insert a sealing rubber plug and tighten the screw cap and nut to maintain the IP67 waterproof rating.
Image: Demonstrates how to seal an unused port on the waterproof junction box using a sealing rubber and screw cap.
6. Final Waterproof Sealing of Junction Box
Ensure the rubber seal of the junction box lid is perfectly fitted into its groove, with no twists or gaps. Use a screwdriver to tighten the lid screws firmly, ensuring a complete waterproof seal.
Image: Shows the final step of securing the lid of the waterproof junction box with screws, ensuring the rubber seal is correctly seated.
Operation
Testing the Light
After completing all connections and ensuring proper sealing, plug the power supply into an electrical outlet. The LED strip should illuminate. If using a dimmer or RGB controller, use the provided remote control to adjust brightness, change colors (for RGB), or select dynamic lighting modes.
Image: A single color LED strip illuminated, with a remote control demonstrating brightness adjustment.
Image: An RGB LED strip displaying various colors, controlled by a remote with a color wheel.
Maintenance
- Cleaning: Periodically clean the surface of the LED strip with a soft cloth and mild, non-abrasive cleaner. Avoid harsh chemicals that could damage the silicone material.
- Inspection: Regularly inspect the LED strip and all connections for any signs of wear, damage, or water ingress. Address any issues promptly.
- Chemical Resistance: The silicone construction is resistant to chlorine, ozone, acids, and alkalis. However, prolonged exposure to extremely high concentrations of chemicals should be avoided.
- Temperature Range: Designed to withstand extreme temperatures from -4°F to 131°F (-20°C to 55°C).
- UV Resistance: The material is UV resistant to prevent yellowing over time.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power, loose connection, incorrect wiring, faulty power supply/controller. | Check power source, ensure all connections are secure and correct polarity is observed. Test power supply/controller. |
| Remote control not responding. | Remote not paired, battery low, obstruction. | Refer to the remote manual for pairing instructions. Replace remote battery. Ensure clear line of sight. |
| Inconsistent light or flickering. | Loose connection, insufficient power, damaged strip. | Check all wiring connections. Ensure power supply wattage is adequate. Inspect strip for physical damage. |
| Water inside junction box. | Improper sealing of screw caps, nuts, or lid. | Immediately disconnect power. Open and dry the box. Re-seal all connections and the lid carefully, ensuring rubber seals are correctly seated. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | 24VNeon-IP68-WW-6M |
| Input Voltage | 24V DC |
| IP Rating | IP68 |
| Submersible Depth | ≤ 9.84ft (3m) |
| Material | Silicone |
| LED Quantity | 120 LEDs/meter |
| LED Chip | SMD 2835 (2700K) |
| Lumen | 474 LM/meter (2700K Warm White) |
| Working Temperature | -4°F to 131°F (-20°C to 55°C) |
| Wattage | 9W/meter |
| Minimum Bending Diameter | 7.87 inches (200mm) |
| CRI | 80+ |
| Dimming | PWS Supported |
| Certification | UL676 |
| Life Span | 50,000 hours+ |
Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact Shine Decor customer service. Keep your purchase receipt for warranty claims.
Shine Decor has been involved in the lighting industry for over 18 years, committed to providing superior products and considerate services.
Visit the Shine Decor Store for more products and information.
