1. Introduction
This manual provides comprehensive instructions for the safe and effective use of your PlusAcc Vacuum Magnetic Phone Holder. Please read this manual thoroughly before installation and operation to ensure optimal performance and longevity of the product.
2. Package Contents
Verify that all items listed below are included in your package:
- 1 x Vacuum magnetic phone holder
- 1 x 1M USB A to Type-C Cable
- 1 x Metal ring (for non-MagSafe phones)
- 1 x Adhesive pad for car dashboard
- 1 x Cleaning kit
Image: Package contents of the PlusAcc Vacuum Magnetic Phone Holder.
3. Important Reminders & Safety
- Surface Requirement: The holder works best on smooth surfaces such as windshields, center screens, and glossy dashboards. For smooth but textured surfaces, use the included adhesive pad for enhanced suction.
- Avoid Curved Surfaces: This product is not suitable for curved, uneven, or irregular leather surfaces.
- Phone Case Thickness: For optimal wireless charging and magnetic hold, ensure your phone case thickness is less than 4mm. Metal cases and wallet cases are not compatible.
- Magnetic Interference: The holder is designed to avoid interference with cell phone signals.
Image: Surface compatibility for the phone holder.
Video: Demonstrates how to check surface smoothness for proper installation.
Video: Illustrates the recommended phone case thickness for optimal performance.
4. Setup Instructions
4.1 Surface Preparation
- Clean the desired mounting surface thoroughly using the provided cleaning kit (wet wipe followed by dry wipe). Ensure the surface is free of dust, grease, and moisture.
- For textured dashboards, peel off the protective film from the adhesive pad and firmly press it onto the cleaned surface. Allow it to set for at least 6 hours before attaching the phone holder.
4.2 Attaching the Phone Holder
- Place the suction cup of the phone holder onto the prepared smooth surface (or the adhesive pad).
- While pressing down firmly on the holder, rotate the locking ring clockwise until it is tight. This activates the vacuum adsorption for a secure hold.
Video: Demonstrates the correct way to apply the suction cup for maximum hold.
4.3 Connecting the Charging Cable
Plug the provided USB A to Type-C cable into the Type-C port on the side of the magnetic charging pad and connect the other end to a suitable USB power source in your vehicle.
4.4 Using the Metal Ring (for non-MagSafe phones)
If your phone or phone case is not MagSafe-compatible, use the included metal ring:
- Clean the back of your phone case.
- Peel off the protective film from the metal ring.
- Carefully align the metal ring to the center of your phone case (ensure it does not obstruct the camera or other features) and press firmly.
- Allow the adhesive on the metal ring to cure for at least 6 hours before attaching it to the phone holder.
Video: Instructions on how to properly use and apply the metal ring for non-magnetic cases.
5. Operating Instructions
5.1 Attaching Your Phone
Simply place your MagSafe-compatible phone (or phone with the installed metal ring) onto the magnetic charging pad. The strong N55 magnets will securely hold your device in place.
Image: Phone securely attached and charging on the holder.
5.2 Adjusting the Viewing Angle
The holder features a 360° rotating base and a dual-axis folding arm, allowing you to adjust your phone to any desired viewing angle for safe navigation or media consumption.
Image: Adjustable viewing angles of the phone holder.
5.3 Wireless Charging
Once your phone is attached and the cable is connected to a power source, wireless charging will begin automatically. The holder supports 15W fast charging.
6. Maintenance
To ensure the longevity and optimal performance of your PlusAcc Vacuum Magnetic Phone Holder, follow these maintenance guidelines:
- Clean the Suction Cup: Periodically clean the suction cup with a damp cloth to remove any dust or debris that may reduce its adhesive strength.
- Clean Mounting Surface: Regularly clean the surface where the holder is mounted to maintain a strong vacuum seal.
- Avoid Extreme Temperatures: While the alloy material is designed for various weather conditions, prolonged exposure to extreme heat or cold may affect the suction cup's performance.
7. Troubleshooting
If you encounter any issues with your PlusAcc Vacuum Magnetic Phone Holder, refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Holder does not stick securely | Surface is not smooth or clean; vacuum seal not properly engaged. | Clean the surface thoroughly. For textured surfaces, use the adhesive pad. Ensure the locking ring is rotated clockwise while pressing down firmly. |
| Phone does not attach magnetically | Phone/case is not MagSafe compatible; metal ring not installed correctly; phone case is too thick or contains metal. | Ensure your phone is MagSafe compatible or has the metal ring correctly installed. Check phone case thickness (must be <4mm) and avoid metal/wallet cases. |
| Phone is not charging wirelessly | Charging cable not connected; phone not aligned correctly; phone case too thick; power source issue. | Verify the USB-C cable is securely connected to the holder and a working power source. Re-position the phone on the magnetic pad for proper alignment. Check phone case thickness. |
Video: Guidance on what to do if your phone does not securely attach to the mount.
8. Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 2.36 x 2.36 x 1.57 inches |
| Item Weight | 3.53 ounces |
| Model Number | Charging (K007S) |
| Brand | PlusAcc |
| Color | Black |
| Compatible Devices | Smartphones (MagSafe-certified or with metal ring) |
| Compatible Phone Models | iPhone 12-17 series, LG, Google, OnePlus, and other smartphones with appropriate magnetic cases/rings. |
| Mounting Type | Direct use (smooth surfaces) or with adhesive pad (textured surfaces) |
| Magnetic Strength | 2400gf N55 magnets |
| Manufacturer | Shenzhen Bilio Technology Co., Ltd. |
9. Warranty & Support
For warranty information, technical support, or any inquiries regarding your PlusAcc Vacuum Magnetic Phone Holder, please contact PlusAcc customer service through the retailer where the product was purchased or visit the official PlusAcc website.