Introduction
Thank you for choosing KEMIMOTO Heated Motorcycle Gloves. These gloves are designed to provide warmth and protection during cold weather activities, particularly for motorcycle riding. They feature independent dual-zone heating for the palm and back of the hand, three adjustable heat levels, and a durable three-layer thermal structure. The integrated 3000 mAh batteries ensure extended heating, while TPU reinforcements offer enhanced protection. This manual provides essential information for the proper setup, operation, and maintenance of your gloves.
Image: KEMIMOTO Heated Motorcycle Gloves providing warmth during a winter ride.
Package Contents
- 1 Pair of KEMIMOTO Heated Motorcycle Gloves
- 2 x 3000 mAh Lithium Polymer Batteries
- 1 x Charging Cable (Type-C)
- User Manual
Setup
1. Charging the Batteries
Before initial use, fully charge both 3000 mAh lithium polymer batteries. Connect the provided Type-C charging cable to the battery and a suitable USB power adapter (not included). The battery indicator light will show charging status.
Image: The KEMIMOTO 3000mAh battery featuring a Type-C charging port for convenience.
2. Installing Batteries
- Locate the battery pocket on the cuff of each glove.
- Carefully insert one fully charged battery into each pocket.
- Connect the glove's power cable to the battery.
- Securely close the battery pocket zipper or flap.
Operating Instructions
1. Powering On/Off
- To Power On: Press and hold the power button on the back of the glove for approximately 3 seconds until the LED indicator illuminates.
- To Power Off: Press and hold the power button for approximately 3 seconds until the LED indicator turns off.
2. Adjusting Heat Levels (Dual-Zone Control)
These gloves feature independent heating control for the palm and the back of the hand. Each zone has its own control button and LED indicator.
Image: Diagram illustrating the independent dual-zone heating control for the palm and back of the hand, with corresponding temperature ranges and battery life for each of the three heat levels.
- High Heat (Red LED): Press the respective zone's button once after powering on. Provides maximum warmth (approx. 131-149°F / 55-65°C) for 3-4 hours.
- Medium Heat (Blue LED): Press the button again. Provides moderate warmth (approx. 122-131°F / 50-55°C) for 4-5 hours.
- Low Heat (Green LED): Press the button a third time. Provides gentle warmth (approx. 104-113°F / 40-45°C) for 6-8 hours.
- To cycle through the heat settings, continue pressing the button.
3. Touchscreen Functionality
The index finger and thumb of each glove are equipped with touchscreen-compatible material, allowing you to operate smartphones or GPS devices without removing your gloves.
Image: Illustration of the two-finger touchscreen functionality and a cross-section diagram showing the water-repellent, heating, and palm suede layers of the glove.
Maintenance
1. Cleaning
- Disconnect and remove batteries before cleaning.
- Hand wash gently with mild soap and cold water. Do not machine wash or tumble dry.
- Do not wring or twist the gloves.
- Air dry thoroughly in a well-ventilated area, away from direct heat or sunlight. Ensure gloves are completely dry before reinserting batteries or storing.
2. Battery Care
- Always disconnect batteries from the gloves when not in use to prevent gradual power loss.
- Store batteries in a cool, dry place.
- For long-term storage, charge batteries to approximately 50% capacity every 3-6 months to maintain battery health.
3. Storage
Store the gloves in a dry, cool place, away from direct sunlight and extreme temperatures. Ensure they are clean and completely dry before storage.
Troubleshooting
- Gloves Not Heating:
- Ensure batteries are fully charged and correctly inserted.
- Verify that the power cables inside the glove are securely connected to the batteries.
- Confirm the power button has been pressed and held for 3 seconds to activate the heating system. - Reduced Heat or Short Battery Life:
- Battery performance can be affected by extremely cold ambient temperatures.
- Ensure batteries are fully charged before each use.
- Older batteries may have reduced capacity over time. - Inner Lining Discomfort:
- Some users may experience the inner lining shifting. When putting on or taking off the gloves, carefully slide your hand in and out to minimize displacement of the inner fabric. If the lining shifts, gently adjust it with your fingers to realign.
Specifications
| Feature | Specification |
|---|---|
| Model Number | F1109-08053-BK2XL |
| Battery Type | Lithium Polymer |
| Battery Capacity | 3000 mAh (per battery) |
| Heat Zones | Dual (Palm and Back of Hand) |
| Heat Levels | 3 (High, Medium, Low) |
| Material | Polyester |
| Protection | TPU Reinforcements |
| Touchscreen Compatibility | 2 Fingers (Index and Thumb) |
| Closure Type | Hook and Loop |
| Dimensions (Package) | 31.2 x 20.4 x 7 cm |
| Weight (Gloves + Batteries) | 750 g |
Image: Size chart providing measurements for middle finger length, palm circumference, and palm length to help determine the correct glove size.
Warranty and Support
For detailed warranty information, please refer to the documentation included with your product or visit the official KEMIMOTO website. If you encounter any issues or require technical assistance, please contact KEMIMOTO customer support or the retailer from whom you purchased the product.
You can often find support contact details on the brand's official website: KEMIMOTO Store on Amazon