ZWP Lexey/Luxey Series Remote
Replacement Remote Control User Manual
For Valuxhome Fireplace Heaters
1. Introduction
This manual provides instructions for the ZWP Replacement Remote Control, designed for use with various Valuxhome Fireplace Heater models. This remote offers a convenient way to operate your fireplace heater from a distance.
Image 1.1: The ZWP Replacement Remote Control, showing its ergonomic design and button layout.
2. Compatibility
This remote control is compatible with the following Valuxhome Fireplace Heater models:
- Lexey42, Lexey 50, Lexey 50 WH, Lexey 60, Lexey 72, Lexey 90
- Luxey42, Luxey 50, Luxey 50 WH, Luxey 60, Luxey 72, Luxey 84, Luxey 95
- EF23T, VEF28, VHBI74, VEF72, MEF36, EF36, EF42, EF50, EF60, EF72, EF84
- VEF30T, VEF33W, VEF40T, EF50T, VWM72, VWM60, WM50-WH, BI42, BI50, VHBI60
3. Features
- Durable Construction: Made of high-quality ABS material, ensuring wear resistance and durability.
- Comfortable Grip: Ergonomically designed for a comfortable hand feeling.
- Soft Silicon Buttons: Environmentally friendly and designed for tactile feedback.
- No Programming Required: Ready to use immediately after battery installation.
- Long Operational Distance: Effective up to 8 meters (approximately 26 feet).
Image 3.1: Front and back view of the remote, highlighting the durable ABS material and soft silicon buttons for comfortable use.
4. Setup
4.1 Battery Installation
The remote control requires two (2) 1.5V AAA batteries (not included). Follow these steps to install the batteries:
- Locate the battery compartment cover on the back of the remote control.
- Slide the cover downwards or press the latch (if present) to open the compartment.
- Insert two 1.5V AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Close the battery compartment cover by sliding it back into place until it clicks securely.
Important: Ensure correct battery polarity. Do not mix old and new batteries, or different types of batteries.
Image 4.1: Front and back view of the remote control, illustrating the battery compartment location and indicating the requirement for two 1.5V AAA batteries.
5. Operating Instructions
Once batteries are installed, the remote control is ready for use. Point the remote directly at your Valuxhome Fireplace Heater and press the desired function button.
5.1 Button Functions
Image 5.1: Close-up view of the remote control buttons, showing the various icons and their positions.
| Button Icon | Function | Description |
|---|---|---|
| (Power Symbol) | Power ON/OFF | Turns the fireplace heater on or off. |
| (Flame Symbol) | Flame Effect | Adjusts or cycles through flame brightness/effect settings. |
| (Heat Wave Symbol) | Heat Setting | Controls the heat output (e.g., low, high, off). |
| (Timer Symbol) | Timer Function | Sets or adjusts the automatic shut-off timer. |
| (Temperature Symbol) | Temperature Control | Adjusts the desired temperature setting. |
The operational distance of the remote control is up to 8 meters (approximately 26 feet), allowing for convenient control from various points in a room.
Image 5.2: The remote control positioned near a fireplace heater, illustrating its effective operational distance of 8 meters.
Image 5.3: A hand holding the remote control, demonstrating its use with a fireplace heater.
6. Maintenance
- Cleaning: Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: Replace batteries when the remote's range decreases or it stops responding. Always replace both batteries at the same time.
- Storage: If the remote will not be used for an extended period, remove the batteries to prevent leakage and damage.
- Avoid Moisture: Keep the remote control away from water and excessive humidity.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not responding | Dead or incorrectly installed batteries. | Replace batteries, ensuring correct polarity (+/-). |
| Reduced range | Low batteries or obstruction between remote and fireplace. | Replace batteries. Ensure a clear line of sight to the fireplace receiver. |
| Specific button not working | Button stuck or internal issue. | Gently press the button multiple times. If issue persists, contact support. |
8. Specifications
- Brand: ZWP
- Compatible Devices: Valuxhome Fireplace Heaters (various Lexey and Luxey models)
- Power Source: 2 x 1.5V AAA Batteries (not included)
- Material: High-quality ABS
- Color: Black
- Special Feature: Ergonomic design
- Max Number of Supported Devices: 1
- Package Dimensions: 6.8 x 2.3 x 1 inches
- Item Weight: 2.08 ounces
9. Support
For any questions or assistance regarding your ZWP Replacement Remote Control, please do not hesitate to contact us before leaving feedback. We are committed to helping you resolve any issues.
Note: Specific warranty information is not provided in the product details. Please refer to your purchase documentation or contact the seller for warranty details.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.