1. Introduction
This instruction manual provides essential information for the safe and efficient operation, installation, and maintenance of your FOTING 1.5HP Shallow Well Pump with Pressure Tank, Model JGP110037C. Please read this manual thoroughly before using the pump to ensure proper function and to prevent injury or damage. Keep this manual for future reference.
Figure 1: FOTING 1.5HP Shallow Well Pump with Pressure Tank
2. Safety Information
Always observe basic safety precautions to reduce the risk of fire, electric shock, and personal injury.
- Electrical Safety: Ensure the pump is connected to a properly grounded 115V, 60Hz power supply. Do not operate with damaged cords or plugs. Avoid using extension cords if possible; if necessary, use a heavy-duty outdoor-rated cord.
- Water Safety: Do not pump flammable or corrosive liquids. Ensure the pump is not operated dry (without water), as this can cause severe damage.
- Personal Safety: Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves during installation and maintenance. Keep children and unauthorized persons away from the operating pump.
- Installation: Install the pump in a well-ventilated area, protected from direct sunlight and freezing temperatures. Ensure all connections are secure and leak-free.
- Maintenance: Disconnect power before performing any maintenance or service.
3. Product Overview
The FOTING 1.5HP Shallow Well Pump with Pressure Tank is designed for efficient water boosting and irrigation applications. It features a powerful motor, a durable pressure tank, and automatic operation capabilities.
Key Features:
- Powerful Motor: 1.5HP motor with a maximum flow rate of 1340 GPH and a maximum lift of 164 feet.
- High Suction Capability: Capable of suctioning water from depths up to 23 feet.
- Integrated Pressure Tank: 5-gallon pressure tank with a pre-set pressure range for automatic operation.
- Automatic Operation: Features a mechanical pressure switch that automatically starts the pump at 1.5 bar and shuts it off at 3 bar.
- Durable Construction: Reinforced thermoplastic structure and a finely finished iron tank for corrosion and wear resistance.
- Safety Features: Equipped with overheat protection to prevent motor burnout and a durable carbon ceramic mechanical seal to prevent water leakage.
- Versatile Connections: 1" NPT outlet and inlet, includes 2 adapters for NPT 1" to GHT 3/4" connections.
Figure 2: Detailed view of pump components including 1" NPT Outlet, 1" NPT Intake, Start Waterproof Cover, 5-Gal Pressure Tank, High Pressure Soft Tube, Pressure Gauge, Mechanical Pressure Switch, and Stable Base.
Figure 3: Key performance specifications and protection features.
Figure 4: Details of the pressure gauge, mechanical pressure switch, and thermal overload protection.
4. Setup and Installation
4.1 Unpacking
Carefully remove all components from the packaging. Inspect for any damage that may have occurred during shipping. Ensure all parts listed in the packing list are present.
4.2 Location
Place the pump on a stable, level surface. The location should be protected from moisture, direct sunlight, and freezing temperatures. Ensure adequate ventilation around the motor.
4.3 Plumbing Connections
- Connect the suction line to the 1" NPT intake port of the pump. Ensure a tight, leak-free connection.
- Connect the discharge line to the 1" NPT outlet port. Use the provided NPT 1" to GHT 3/4" adapters if connecting to a standard garden hose.
- It is recommended to install a check valve on the suction line to prevent water from flowing back into the well or source, especially for self-priming applications.
- Ensure all pipes and fittings are compatible with the intended water pressure and temperature.
Figure 5: Connection options for water taps and self-priming setups.
4.4 Priming the Pump
Before first use, the pump must be primed.
- Locate the priming plug on the top of the pump housing.
- Remove the priming plug and slowly fill the pump casing with water until it overflows.
- Replace the priming plug securely.
- Ensure the suction line is fully submerged in the water source.
4.5 Electrical Connection
Connect the pump to a standard 115V, 60Hz grounded electrical outlet. Ensure the power switch on the pump is in the "OFF" position before plugging it in.
5. Operating Instructions
5.1 Starting the Pump
- Ensure the pump has been properly primed (see Section 4.4).
- Turn the power switch to the "ON" position. The pump will start to draw water.
- Observe the pressure gauge. The pump's mechanical pressure switch is set to automatically start when pressure drops below 1.5 bar and shut off when it reaches 3 bar. The maximum pressure the tank can hold is 4.5 bar.
- Allow the pump to run until a steady flow of water is achieved and the pressure stabilizes.
5.2 Applications
This pump is suitable for various applications including:
- Garden and lawn irrigation.
- Agricultural structures and small farms.
- Domestic water supply for homes and cabins.
- Pipe pressurization and water transfer.
Figure 6: Pump in use for garden irrigation.
Figure 7: Versatile applications of the FOTING pump.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your FOTING pump. Always disconnect power before performing any maintenance.
6.1 General Cleaning
- Keep the pump exterior clean and free from debris.
- Ensure ventilation openings are not blocked to prevent overheating.
6.2 Winterization (for cold climates)
If the pump is exposed to freezing temperatures, it must be drained to prevent damage.
- Disconnect the pump from the power supply.
- Drain all water from the pump casing and pressure tank by opening drain plugs and disconnecting pipes.
- Store the pump in a warm, dry place during winter months.
6.3 Mechanical Seal
The pump is equipped with a durable carbon ceramic mechanical seal designed to prevent water leakage and extend service life. If leakage occurs around the shaft, inspect the seal for wear or damage and replace if necessary.
7. Troubleshooting
Refer to the table below for common issues and their solutions. If the problem persists, contact FOTING customer service.
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not start. | No power; tripped circuit breaker; faulty switch; motor overload. | Check power connection; reset breaker; inspect switch; allow motor to cool if overheat protection activated. |
| Pump runs but no water or low flow. | Pump not primed; air leak in suction line; clogged intake; low water source. | Re-prime the pump; check suction line for leaks; clear intake; ensure adequate water source. |
| Pump cycles on and off frequently. | Air in pressure tank; pressure switch malfunction; small leak in system; no check valve on suction line. | Check air charge in tank; inspect pressure switch; check for leaks in plumbing; install a check valve on the suction line if not present. |
| Pump is noisy. | Cavitation (air in water); worn bearings; foreign object in impeller. | Ensure pump is fully primed and suction line is sealed; inspect impeller for obstructions; contact service if bearings are suspected. |
| Water leakage. | Loose connections; damaged mechanical seal; cracked housing. | Tighten all connections; inspect and replace mechanical seal if damaged; contact service for housing damage. |
8. Specifications
| Attribute | Value |
|---|---|
| Brand | FOTING |
| Model Number | JGP110037C |
| Power | 1.5 HP |
| Voltage | 115 Volts |
| Frequency | 60 Hz |
| Max Flow Rate | 1340 GPH |
| Max Lift (Head) | 164 Feet |
| Max Suction Lift | 23 Feet |
| Pressure Tank Capacity | 5 Gallons |
| Automatic Pressure Switch On | < 1.5 bar |
| Automatic Pressure Switch Off | > 3.0 bar |
| Max Pressure (Tank) | 4.5 bar |
| Inlet/Outlet Size | 1" NPT |
| Material | Plastic, Metal |
| Product Dimensions (L x W x H) | 17" x 10.5" x 20" |
| Item Weight | 33.7 pounds |
| Protection Type | IPX4 |
| Max Fluid Temperature | 95°F |
Figure 8: Pump working performance chart.
9. Warranty and Customer Support
FOTING is committed to providing high-quality products and excellent customer service.
9.1 Warranty Information
Specific warranty details may vary. Please refer to the product packaging or contact FOTING customer service for comprehensive warranty information regarding your 1.5HP Shallow Well Pump with Pressure Tank.
9.2 Customer Support
For technical support, troubleshooting assistance, or any inquiries regarding your FOTING product, please contact our customer service team. Our professionals are available to provide support and ensure your water system remains stable.
You can find contact information on the official FOTING website or through your purchase platform.