1. Introduction
The WUBEN PL01 is a compact, high-performance pen light designed for various applications including home use, outdoor activities, emergencies, and inspections. It features a bright 650-lumen output, dual power options (rechargeable battery or AAA batteries), IP68 waterproof rating, and a durable aluminum alloy construction. This manual provides detailed instructions for its safe and effective use.
Image 1.1: The WUBEN PL01 Pen Light, showcasing its sleek design and compact size.
2. What's in the Box
Please verify that all items are present upon opening the package:
- WUBEN PL01 Pen Light x 1
- Rechargeable Battery (pre-installed or separate) x 1
- Type-C Charging Cable x 1
- Lanyard x 1
- Spare O-rings x 2
- User Manual (this document) x 1
Image 2.1: Contents of the WUBEN PL01 package, including the pen light, charging cable, lanyard, and spare O-rings.
3. Setup
3.1 Battery Installation
The WUBEN PL01 supports two power sources: the included rechargeable battery or two standard AAA batteries (not included). Ensure correct polarity during installation.
- Unscrew the tail cap of the flashlight.
- Insert the rechargeable battery or two AAA batteries with the positive (+) end facing towards the head of the flashlight.
- Securely re-screw the tail cap until it is fully tightened.
Image 3.1: Illustration of the dual power options for the WUBEN PL01, showing both the rechargeable battery and AAA battery configuration.
3.2 Charging the Rechargeable Battery
The included rechargeable battery features a built-in USB-C charging port. The flashlight itself does not have an integrated charging port.
- Unscrew the tail cap and remove the rechargeable battery from the flashlight.
- Connect the provided USB-C charging cable directly to the charging port on the battery.
- Connect the other end of the USB-C cable to a compatible USB power source (e.g., wall adapter, computer USB port).
- A red indicator light on the battery signifies that it is charging.
- The indicator light will turn green when the battery is fully charged.
- Charging typically takes approximately 1.5 hours.
- Once charged, reinsert the battery into the flashlight and secure the tail cap.
4. Operating Instructions
4.1 Power On/Off
To turn the WUBEN PL01 on or off, perform a full press of the tail switch button.
4.2 Mode Switching
With the light turned on, half-press the tail switch button to cycle through the available brightness modes in the following sequence:
- Moon: 1 Lumen
- Low: 50 Lumens
- Medium: 150 Lumens
- High: 650 Lumens
The flashlight features a mode memory function, meaning it will activate in the last used brightness mode when turned on again.
Image 4.1: Diagram illustrating the tail switch operation for power on/off and mode cycling.
Image 4.2: Examples of the WUBEN PL01's four brightness modes in various practical scenarios, from facial examination to night walking.
4.3 Dual-Direction Clip Usage
The WUBEN PL01 is equipped with a versatile two-way clip, allowing for secure attachment to various items for hands-free lighting.
- Pocket Carry: Attach the clip to a shirt pocket or pants pocket for easy access.
- Backpack Strap: Secure the flashlight to a backpack strap for illumination during hikes or walks.
- Cap Mount: Clip the flashlight to the brim of a cap to convert it into a temporary headlamp.
Image 4.3: Demonstrates the versatility of the dual-direction clip, showing the flashlight attached to a pocket, backpack strap, and cap.
5. Maintenance
5.1 Cleaning
To maintain optimal performance and appearance:
- Clean the flashlight body with a soft, damp cloth. Avoid harsh chemicals or abrasive materials.
- For the lens, use a clean, soft cloth specifically designed for optical surfaces.
5.2 O-ring Replacement
The PL01's IP68 waterproof rating relies on properly sealed O-rings. Periodically inspect them for any signs of wear, cracks, or damage.
- If O-rings appear damaged, replace them with the provided spare O-rings.
- Apply a thin layer of silicone grease to the O-rings to ensure a better seal and prevent drying.
5.3 Battery Care
- If the flashlight will not be used for an extended period, remove the batteries to prevent potential leakage and damage.
- For the rechargeable battery, recharge it every 3-6 months to maintain its overall lifespan and capacity.
Image 5.1: The WUBEN PL01's Type III hard-anodized aluminum body, highlighting its scratch, rust, and impact resistance.
Image 5.2: The WUBEN PL01 demonstrating its IP68 waterproof and 2-meter impact resistance, suitable for demanding environments.
6. Troubleshooting
If you encounter issues with your WUBEN PL01, please refer to the following common problems and solutions:
- Light does not turn on:
- Ensure the batteries are installed with correct polarity.
- Check if the rechargeable battery is charged, or if AAA batteries are new.
- Verify that the tail cap is fully tightened. A loose tail cap can prevent electrical contact.
- Clean the battery contacts and the contact points inside the flashlight with a clean cloth.
- Light flickers or dims unexpectedly:
- The battery level may be low. Recharge the included battery or replace AAA batteries.
- Ensure the tail cap is securely tightened.
- Clean battery contacts and internal contact points.
- Water ingress (if exposed to water):
- Immediately turn off the flashlight and remove the batteries.
- Inspect the O-rings for any damage, tears, or improper seating. Replace if necessary.
- Ensure the tail cap was fully tightened before exposure to water.
- Allow the flashlight to dry completely before reassembling and attempting to use it.
If the problem persists after attempting these solutions, please contact WUBEN customer support.
7. Specifications
| Feature | Detail |
|---|---|
| Model | PL01 |
| Output Modes | High (650 Lumens), Medium (150 Lumens), Low (50 Lumens), Moon (1 Lumen) |
| Runtime | High: 1 hour, Medium: 2.5 hours, Low: 7 hours, Moon: 125 hours |
| Battery Type | Rechargeable (Included) / 2 x AAA Battery (Not Included) |
| Beam Distance | 110 Meters |
| Peak Beam Intensity | 3000 CD |
| LED | 1 x 315D |
| Waterproof Rating | IP68 (Submersible in 2m water for 1 hour) |
| Impact Resistance | 2 Meters |
| Weight | 1.59 oz (with battery) |
| Dimensions (L x D) | 5.31 inches x 0.59 inches |
| Material | Anodized Aluminum |
| Color Temperature | 5000 Kelvin |
Image 7.1: Diagram illustrating the internal components of the WUBEN PL01, focusing on the 315D LED emitter and optical system.
8. Warranty Information
WUBEN products typically come with a manufacturer's warranty. For specific warranty terms, conditions, and registration details, please refer to the official WUBEN website or contact their customer support. Keep your purchase receipt as proof of purchase for any warranty claims.
9. Customer Support
For further assistance, product inquiries, or technical support, please visit the official WUBEN website or contact their customer service department. You can often find FAQs, troubleshooting guides, and contact information on their website.
Official WUBEN Store: WUBEN Store on Amazon
