Hyper Tough HT Charge 20V Max Lithium-Ion Battery 1.5 Ah

Hyper Tough HT Charge 20V Max Lithium-Ion Battery 1.5 Ah User Manual

Comprehensive instructions for safe and effective use.

1. Introduction

This manual provides essential information for the safe operation, maintenance, and storage of your Hyper Tough HT Charge 20V Max Lithium-Ion Battery 1.5 Ah. Please read these instructions carefully before using the battery to ensure optimal performance and safety.

2. Important Safety Instructions

WARNING: Failure to follow these safety instructions may result in fire, electric shock, or serious injury.

  • Always use the battery with compatible Hyper Tough 20V Max tools and chargers. Using incompatible accessories may cause damage or injury.
  • Do not immerse the battery in water or other liquids.
  • Do not store or use the battery in locations where the temperature may reach or exceed 104°F (40°C), such as in direct sunlight or inside a vehicle.
  • Do not incinerate the battery. It may explode in a fire.
  • Do not short-circuit the battery terminals. Avoid contact with conductive materials like keys, coins, or jewelry.
  • Do not disassemble, open, or modify the battery pack.
  • If battery fluid leaks, avoid contact with skin and eyes. If contact occurs, flush with water and seek medical attention.
  • Keep the battery out of reach of children.
  • Dispose of batteries responsibly according to local regulations. Do not dispose of in household waste.

3. Product Overview

The Hyper Tough HT Charge 20V Max Lithium-Ion Battery 1.5 Ah provides reliable power for your Hyper Tough 20V Max cordless tools. Its compact design and lithium-ion technology offer consistent performance.

Hyper Tough HT Charge 20V Max Lithium-Ion Battery 1.5 Ah

An image showing the Hyper Tough HT Charge 20V Max Lithium-Ion Battery 1.5 Ah. The battery is black with a red label displaying 'HT CHARGE' and '20V MAX 1.5Ah LITHIUM-ION'.

4. Setup and Initial Charge

  1. Unpacking: Carefully remove the battery from its packaging. Inspect for any signs of damage.
  2. Charging: Before first use, fully charge the battery using a compatible Hyper Tough 20V Max battery charger. Follow the charger's instructions for proper charging procedures.
  3. Installation: Align the battery with the battery slot on your Hyper Tough 20V Max tool. Slide the battery into place until it clicks securely. Ensure it is firmly seated before operation.

5. Operating Instructions

  • Battery Level: Monitor the battery charge level, if indicated on your tool or charger, to avoid complete discharge, which can reduce battery life.
  • Overheating: If the battery becomes excessively hot during use, discontinue operation and allow it to cool down before recharging or resuming work.
  • Removal: To remove the battery from a tool, press the release button (if present) and slide the battery out.

6. Maintenance and Storage

  • Cleaning: Keep the battery terminals clean and free of dirt or debris. Use a dry cloth to wipe the battery. Do not use solvents or harsh chemicals.
  • Storage: Store the battery in a cool, dry place, away from direct sunlight and extreme temperatures. Ideally, store batteries with a partial charge (around 50%) for extended periods.
  • Long-Term Storage: For long-term storage, recharge the battery every 3-6 months to maintain its health.

7. Troubleshooting

ProblemPossible CauseSolution
Battery not chargingCharger not plugged in; faulty charger; battery too hot/cold; poor connection.Ensure charger is properly connected to power and battery. Check charger for damage. Allow battery to reach room temperature. Clean battery terminals.
Tool not operating with charged batteryBattery not fully inserted; tool malfunction; battery fault.Ensure battery is securely clicked into place. Test battery with another compatible tool or charger. If issue persists, contact support.
Reduced run timeBattery nearing end of life; operating in extreme conditions; heavy load.Ensure battery is fully charged. Avoid continuous heavy-duty use. Consider replacing the battery if it's old.

8. Specifications

  • Model: HT Charge 20V Max Lithium-Ion Battery 1.5 Ah
  • Voltage: 20V Max
  • Capacity: 1.5 Ah
  • Battery Type: Lithium-Ion
  • Product Dimensions: 6 x 6 x 6 inches
  • Manufacturer: Hyper Tough

9. Warranty and Support

This Hyper Tough battery is covered by a limited warranty against defects in materials and workmanship. For specific warranty details, please refer to the warranty card included with your purchase or visit the official Hyper Tough website. For technical support or service inquiries, please contact Hyper Tough customer service.

Related Documents - HT Charge 20V Max Lithium-Ion Battery 1.5 Ah

PreviewHyper Tough 20V Max Cordless Reciprocating Saw Instruction Manual - AQ80002G
Comprehensive instruction manual for the Hyper Tough 20V Max HT Charge Lithium-Ion Cordless Reciprocating Saw (Model AQ80002G), covering safety guidelines, operation, maintenance, troubleshooting, and specifications.
PreviewHyper Tough 20V MAX Lithium-Ion Cordless Drill/Driver AQ75034G User Manual
Comprehensive user manual for the Hyper Tough 20V MAX Lithium-Ion Cordless Drill/Driver (Model AQ75034G), covering safety, operation, technical specifications, troubleshooting, and warranty information.
PreviewHyper Tough 8.0V Max Cordless Rotary Tool Instruction Manual
This manual provides comprehensive instructions for the Hyper Tough 8.0V Max Lithium-ion Cordless Rotary Tool, covering safety guidelines, operation, maintenance, accessory usage, and specifications. Learn how to safely operate and care for your rotary tool.
PreviewHyper Tough 20V Max Cordless Chainsaw FAQ and Guide
Frequently asked questions and essential information about the Hyper Tough 20V Max Cordless 10-Inch Self-Lubricating Chainsaw, including setup, maintenance, and warranty.
PreviewHyper Tough 20V 7.5-Inch Fan Operator's Manual
Comprehensive operator's manual for the Hyper Tough 20V 7.5-Inch Fan (Model C1005), detailing safety, operation, maintenance, and troubleshooting. Essential guide for safe and effective use.
PreviewHyper Tough HT19-401-003-11 20V Max Cordless Chain Saw Quick Start Guide
Quick start guide for the Hyper Tough HT19-401-003-11 20V Max Cordless Chain Saw, covering charging, battery installation, assembly, and safe operation procedures.