Introduction
The Evenflo LiteMax 30 Infant Car Seat is designed to provide safety and comfort for infants weighing between 3 and 30 pounds. This manual provides essential information for proper installation, operation, maintenance, and troubleshooting to ensure the safe use of your car seat.
Figure 1: Evenflo LiteMax 30 Infant Car Seat, River Stone
Key Features:
- Lightweight Design: Extremely lightweight for easy portability.
- Extended Use: Accommodates infants from 3 to 30 lb.
- Adjustable Harness: Features 4 shoulder harness positions to adapt as your child grows.
- Ergonomic Handle: Designed for comfortable carrying.
- Full Coverage Canopy: Provides protection from sun, wind, and rain.
- Easy Installation: Base equipped with a vehicle belt lock-off for quick and secure installation.
- Safety Standards: Meets or exceeds all applicable Federal Safety Standards, including structural integrity, rollover performance, and temperature testing.
Setup and Installation
Proper installation is crucial for your child's safety. Always refer to your vehicle's owner's manual for specific car seat installation instructions and locations.
Installing the Car Seat Base:
- Place the car seat base on the vehicle seat in a rear-facing position. Ensure it is level.
- Route the vehicle's lap belt or LATCH system through the designated belt path on the base.
- Engage the vehicle belt lock-off mechanism to secure the base tightly. The base should not move more than one inch side-to-side or front-to-back at the belt path.
- Verify the recline angle using the built-in recline indicator on the base. The indicator should be within the acceptable range for your infant's weight.
Figure 2: Securing the car seat base with the vehicle belt lock-off.
Figure 3: Recline indicator and harness adjustment points.
Attaching the Infant Carrier to the Base:
- Align the infant carrier with the base.
- Lower the carrier onto the base until it clicks securely into place.
- Always check that the carrier is firmly attached to the base by lifting it slightly.
Operating the Car Seat
Placing Your Child in the Car Seat:
- Unbuckle the harness and loosen the shoulder straps.
- Place your infant in the car seat with their back flat against the seat back.
- Bring the harness straps over your child's shoulders and between their legs.
- Buckle the crotch buckle, then connect the chest clip. The chest clip should be positioned at armpit level.
- Tighten the harness straps until they are snug against your child's body. You should not be able to pinch any excess webbing at the shoulder.
Figure 4: Infant properly secured in the car seat harness.
Adjusting the Canopy:
The full-coverage canopy can be adjusted by pulling it forward or pushing it back to shield your child from the elements.
Figure 5: Car seat with canopy extended for protection.
Maintenance and Care
Cleaning Instructions:
- Fabric Pads: The fabric pads are removable and machine washable. Use cold water and a gentle cycle. Tumble dry on low heat or air dry. Do not use bleach.
- Harness Straps: Wipe harness straps with a damp cloth. Do not machine wash or submerge harness straps in water, as this can weaken the webbing.
- Plastic and Metal Parts: Wipe plastic and metal parts with a soft, damp cloth and mild soap. Do not use abrasive cleaners or solvents.
Figure 6: Cleaning the car seat fabric and base.
Storage:
Store the car seat in a cool, dry place away from direct sunlight when not in use for extended periods.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Car seat base is loose after installation. | Vehicle belt not tight enough or lock-off not engaged. | Re-read installation instructions. Ensure vehicle belt is pulled taut and the lock-off is fully engaged. Apply pressure to the base while tightening. |
| Harness straps are difficult to tighten or loosen. | Straps may be twisted or obstructed. | Check for twists in the harness straps. Ensure no fabric or clothing is obstructing the harness mechanism. |
| Infant carrier does not click securely into the base. | Misalignment or obstruction. | Ensure the carrier is properly aligned with the base's connection points. Check for any debris obstructing the connection. |
If you encounter issues not covered here or require further assistance, please contact Evenflo ParentLink Consumer Care.
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 28.5 x 19 x 24 inches (72.4 x 48.3 x 61 cm) |
| Item Model Number | CS100112042 |
| Maximum Weight Recommendation | 30 Pounds (13.6 kg) |
| Minimum Weight Recommendation | 3 Pounds (1.4 kg) |
| Material Type | 100% Polyester |
| Number of Reclining Positions | 4 |
| Harness Type | 5-Point |
| Orientation | Rear Facing |
| Item Weight | 8.17 pounds (3.7 kg) |
Figure 7: Product dimensions diagram.
Warranty Information
Evenflo products are manufactured with quality and durability in mind. For specific warranty details, including coverage period and terms, please refer to the warranty card included with your product packaging or visit the official Evenflo website. Keep your proof of purchase for warranty claims.
Customer Support
Evenflo is committed to providing excellent customer service. If you have questions about your LiteMax 30 Infant Car Seat, need assistance with installation, or require support, please contact our ParentLink Consumer Care Team.
- Online Support: Visit the Evenflo website for FAQs and support resources.
- Live Video Support: Evenflo offers live video support with certified car seat safety technicians to assist with proper vehicle installation. This service can help you install your car seat with confidence.
- Contact Information: Refer to the contact details provided in your product packaging or on the official Evenflo website for phone numbers and email support.
For more information about Evenflo products and services, you can visit the Evenflo Store on Amazon.
