1. Introduction
This manual provides essential instructions for the safe and efficient operation of your ICERIVER ALEO AE1 LITE 300MH/S 500W ALEO Miner. Please read this manual thoroughly before installation and use, and retain it for future reference. This device is designed for specialized computational tasks using the zkSNARK algorithm.
2. Safety Information
Observe the following safety precautions to prevent damage to the device or personal injury:
- Ensure the power supply voltage matches the device's requirements (100-240V AC).
- Do not operate the device in environments with excessive dust, humidity, or extreme temperatures.
- Maintain adequate ventilation around the device to prevent overheating. Do not block the fan vents.
- Disconnect power before performing any maintenance or cleaning.
- Do not attempt to open the device casing or modify its components. Unauthorized modifications will void the warranty.
- Keep the device away from flammable materials.
3. Package Contents
Verify that all items are present in the package:
- ICERIVER ALEO AE1 LITE 300MH/S Miner Unit
- Power Supply Unit (PSU)
- Power Cable (region-specific)
- This User Manual
4. Product Overview
Familiarize yourself with the main components and interfaces of your ALEO Miner.
Figure 4.1: Front and Side View. This image displays the front and left side of the ICERIVER ALEO AE1 LITE Miner, highlighting the dual cooling fans on the front panel, protected by a metal grille. The robust black casing is visible.
Figure 4.2: Rear Panel Overview. This image shows the rear panel of the ICERIVER ALEO AE1 LITE Miner. Key features include the Ethernet port, status indicator lights (red and green), a reset button, a micro SD card slot, an antenna connector, the main power switch, and the AC power input socket.
4.1. Front Panel
- Cooling Fans: Two high-speed fans for heat dissipation.
4.2. Rear Panel
- Ethernet Port: For network connection.
- Status Indicators: LED lights indicating device status (e.g., power, network activity).
- Reset Button: To restart the device.
- Micro SD Card Slot: For firmware updates or configuration.
- Antenna Connector: For wireless connectivity (if applicable).
- Power Switch: Main on/off switch.
- AC Power Input: Connects to the power cable.
5. Setup Instructions
- Unpacking: Carefully remove the miner unit and all accessories from the packaging. Inspect for any visible damage.
- Placement: Place the miner on a stable, flat surface in a well-ventilated area. Ensure there is at least 20 cm of clear space around all sides for proper airflow. Avoid direct sunlight or heat sources.
- Network Connection: Connect an Ethernet cable from your router or network switch to the Ethernet port on the rear panel of the miner.
- Power Connection:
- Connect the power cable to the Power Supply Unit (PSU).
- Connect the PSU output cable to the AC Power Input on the rear panel of the miner.
- Plug the power cable into a grounded electrical outlet (100-240V AC).
- Initial Power On: Flip the main power switch on the rear panel to the 'ON' position. The status indicator lights should illuminate.
6. Operating Instructions
6.1. Power On/Off
- Power On: Ensure all cables are securely connected. Flip the power switch to 'ON'. The device will begin its startup sequence.
- Power Off: To safely power off the device, flip the power switch to 'OFF'. For extended periods of inactivity or relocation, disconnect the power cable from the electrical outlet.
6.2. Network Configuration
The miner typically obtains an IP address automatically via DHCP. To access the miner's web interface for detailed configuration:
- Identify the miner's IP address using your router's administration page or a network scanning tool.
- Open a web browser on a computer connected to the same network.
- Enter the miner's IP address into the browser's address bar.
- Log in using the default credentials (refer to manufacturer's documentation or device label for default username/password).
- Configure mining pool settings and other parameters as required for ALEO mining.
7. Maintenance
7.1. Cleaning
- Regularly clean the exterior of the device with a soft, dry cloth.
- Use compressed air to gently clear dust from the fan vents and grilles. Ensure the device is powered off and unplugged before cleaning.
- Do not use liquid cleaners or solvents.
7.2. Environmental Conditions
- Maintain an ambient operating temperature between 0°C and 40°C (32°F and 104°F).
- Ensure relative humidity is within acceptable limits (typically 5% to 95% non-condensing).
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Power cable loose; power switch off; no power from outlet. | Check power cable connections; ensure power switch is 'ON'; test outlet with another device. |
| No network connection. | Ethernet cable loose/faulty; router issue; incorrect network settings. | Verify Ethernet cable connection; try a different cable; restart router; check miner's network configuration via web interface. |
| Overheating. | Blocked vents; insufficient airflow; high ambient temperature. | Ensure vents are clear; move device to a cooler, well-ventilated area; clean dust from fans. |
| Miner not detected by mining pool. | Incorrect pool settings; network firewall; miner not fully initialized. | Double-check mining pool URL, username, and password in the web interface; ensure network firewall allows outbound connections; allow sufficient time for miner to connect after power-on. |
9. Specifications
| Feature | Detail |
|---|---|
| Model | ALEO AE1 LITE 300MH |
| Algorithm | zkSNARK (ALEO) |
| Hashrate | 300 MH/s (±5%) |
| Wall Power | 500 W/h (±10%) |
| Voltage Input | 100-240V AC |
| Connection | Ethernet |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Dimensions (Unit) | 205 × 110 × 202 mm (8.07 x 4.33 x 7.95 inches) |
| Gross Weight (with packaging) | 4.69 KG (10.34 lbs) |
| Net Weight | 4.02 KG (8.86 lbs) |
| Cooling Method | Air Cooling |
| Power Supply Design | Non-Modular |
10. Warranty and Support
This product is provided as brand new. For any operational issues or technical support, please contact the seller directly. The manufacturer's warranty terms apply. Please note the following:
- Unauthorized modifications or opening the device casing will void the warranty.
- Returns for reasons other than quality issues may be subject to a restocking fee (e.g., 30% of the product price). Please ensure this product meets your requirements before purchase.
For further assistance, refer to the contact information provided by your retailer or the official ICERIVER support channels.
