ELEMARA 24V 2 Seater Ride on ATV User Manual

1. Introduction and Product Overview

The ELEMARA 24V 2 Seater Ride on ATV is an electric 4-wheeler quad car designed for big kids, offering an exciting and safe riding experience. It features powerful 400W motors, allowing for speeds up to 5mph, and a spacious two-seater design for shared adventures.

Key features include:

• 24V 4WD System: Equipped with four 100W motors for robust performance.
• Two-Seater Design: An extended 18-inch seat accommodates two children with a maximum capacity of 130 lbs.
• Enhanced Safety: Features spring suspension shock absorbers for a smooth ride and soft-start technology for gradual acceleration.
• Multi-Road Riding Wheels: Large treaded wheels and front wheel shock-absorbing springs make it suitable for various surfaces including concrete, gravel, grass, and shallow sand.
• Interactive Features: Includes bright LED headlights, a pedal accelerator, forward/reverse function, USB port, music, speed and volume adjustment, and a power display.

Image: The ELEMARA 24V 2 Seater Ride on ATV in Leaf Red, showcasing its robust design and LED headlights.

Image: Two children comfortably seated on the ELEMARA ATV, demonstrating its two-seater capability.

2. Safety Information

WARNING: CHOKING HAZARD - Small parts. This product contains small parts. Keep children away during assembly to prevent choking hazards.

• Always supervise children when operating the ATV.
• Ensure all assembly steps are completed correctly and all fasteners are secure before use.
• Do not operate the ATV near roads, motor vehicles, steep inclines, swimming pools, or other bodies of water.
• Always wear appropriate safety gear, including a helmet, when riding.
• Ensure children wear shoes when operating the ATV.
• Do not exceed the maximum weight capacity of 130 lbs.

3. What's in the Box

Upon opening the package, you should find the following components:

• ELEMARA 2 Seater Kids ATV (Main Body) x 1
• Instruction Manual x 1
• Front Bumper x 1
• Dual Drive Front Bracket Assembly (with motors) x 1
• Rear Axle x 1
• Rear Gear Boxes x 2
• Wheels x 4
• Backrest x 1
• Steering Wheel Assembly x 1
• Assorted Screws, Nuts, and Gaskets for assembly
• Charging Cable x 1

4. Setup and Assembly

Follow these steps to assemble your ELEMARA 24V 2 Seater Ride on ATV. It is recommended to have an adult perform the assembly.

Step 1: Install the Front Bumper

1. Locate the front bumper and align it with the mounting points on the front of the ATV body.
2. Secure the front bumper using the provided 4 x M4*12mm screws. Ensure it is firmly attached.

Image: The front of the ATV with the bumper being installed, showing the screw points.

Step 2: Install the Dual Drive Front Bracket

1. Carefully turn the ATV body upside down.
2. Position the dual drive front bracket assembly (which includes the front motors) into the designated slots at the front underside of the ATV.
3. Secure the bracket using the appropriate screws and nuts. Ensure the motor wires are not pinched.

Step 3: Install the Rear Axle

1. On the underside of the ATV, remove the 8 screws securing the two black plates where the rear axle will pass through.
2. Insert the rear axle through the openings.
3. Reattach the black plates and secure them with the 8 screws.

Step 4: Install the Back Gear (Gearboxes)

1. Slide the two gearboxes onto the ends of the rear axle. Ensure the 'L' and 'R' markings on the gearboxes match the corresponding sides of the ATV.
2. Secure the gearboxes to the ATV body using the provided fasteners.

Step 5: Install the Wheels

1. For each wheel, slide it onto its respective axle (front and rear).
2. Place a washer (Φ12 gasket) onto the axle, followed by an M10 nut.
3. Tighten the nuts using the provided tool. For the rear wheels, tighten both sides simultaneously in opposite directions to ensure proper seating.

Image: The large treaded wheels of the ATV, designed for diverse terrains.

Step 6: Install the Backrest

1. Locate the backrest.
2. Insert the backrest into the designated slot at the rear of the seat area until it clicks securely into place.

Step 7: Install the Steering Wheel

1. Carefully align the steering wheel assembly with the steering column.
2. Push the steering wheel down onto the column.
3. Secure the steering wheel by inserting and tightening the screw through the top of the steering wheel into the column.

Step 8: Connect the Power Supply and Install the Seat

1. Lift the main seat cover to access the battery compartment.
2. Connect the red battery terminal to the corresponding red wire, and the black battery terminal to the corresponding black wire. Ensure connections are secure.
3. Carefully place the seat back onto the ATV body, ensuring all wires are tucked away and not pinched. Secure the seat with any retaining screws or clips.

5. Operating Instructions

Familiarize yourself with the controls before operating the ATV.

Power On/Off

• Press the Power Button on the control panel to turn the ATV on or off.

Driving Controls

• Pedal Accelerator: Press the foot pedal to move the ATV forward. Release to brake.
• Forward/Reverse Function: Use the switch on the control panel to select between forward and reverse gears.
• Speed Adjustment: The ATV has two speeds: a low speed of 4 MPH and a high speed of 5 MPH. Use the speed selection button on the control panel to switch between them.
• Soft Start: The soft-start technology ensures gradual acceleration, providing a smoother and safer driving experience for children.

Entertainment Features

• Music: The ATV comes with pre-loaded music. Use the control panel buttons to play, pause, skip tracks, and adjust volume.
• USB Port: Connect a USB device to play your own audio files.
• Bluetooth: Pair your mobile device via Bluetooth to stream music through the ATV's speakers.
• LED Headlights: The bright LED headlights illuminate automatically when the ATV is in operation.

6. Maintenance

Charging the Battery

• The ATV features a low-battery warning system that automatically reminds you when charging is needed.
• Locate the charging socket, typically at the rear of the ATV (often under a small cover labeled "SOCKET").
• Pull down the white small piece covering the charging port.
• Plug the charging cable into the rear of the car's charging socket.
• Plug the charger plug into a standard power supply outlet.
• During charging, the ATV is in a protected state and cannot be operated.
• For the first use, charge the battery for 4-6 hours. Subsequent charges should be for 8-12 hours, or until the charging indicator shows a full charge. Do not overcharge.

Image: The ATV highlighting its dimensions and the location of the charging port.

General Care

• Regularly inspect the ATV for any loose parts, damaged wires, or worn components.
• Clean the ATV with a damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Store the ATV in a dry, cool place away from direct sunlight and moisture when not in use.

7. Troubleshooting

8. Specifications

9. Warranty and Support

Specific warranty information is not provided in the available product data. Please refer to the product packaging or contact ELEMARA customer support for details regarding warranty coverage and technical assistance.

For further inquiries or support, please visit the official ELEMARA store: ELEMARA Store on Amazon