Introduction
The Hebuck HT-10 is a digital temperature and humidity controller designed for egg incubators. It provides precise control over environmental conditions, including temperature, humidity, egg turning, and ventilation, to support successful hatching. This manual provides essential information for the safe and effective use of your HT-10 controller.
Safety Information
- Always ensure the power supply matches the controller's voltage requirements (AC220V/110V).
- Do not expose the controller to water or excessive moisture.
- Keep the device away from flammable materials.
- Ensure proper ventilation around the controller to prevent overheating.
- Disconnect power before performing any maintenance or wiring adjustments.
- This device is not a toy. Keep out of reach of children.
Product Overview
The HT-10 controller features a clear digital display and intuitive controls for managing your incubator's environment. It integrates high-precision sensors for accurate temperature and humidity readings.
Image: Hebuck HT-10 Incubator Controller highlighting its intelligent features.
Key Features:
- Dual Mode Functionality: Supports both Fahrenheit and Celsius temperature displays.
- User-Friendly Operation: Clear digital tube display and intuitive panel functions.
- Comprehensive Control: Pre-configured adjustments for temperature, humidity, egg turning, and ventilation.
- Reliable Performance: Maintains stable temperature and humidity with automated egg turning and ventilation cycles.
- High Accuracy: Temperature measurement accuracy of ±0.1°C/°F and humidity control accuracy of ±3%RH.
Image: Physical dimensions of the HT-10 controller.
The controller measures approximately 9.7 cm (3.8 in) in length, 9 cm (3.5 in) in width, and 5.4 cm (2.1 in) in height.
Setup
Wiring Instructions:
Proper wiring is crucial for the safe and correct operation of the HT-10 controller. Refer to the diagram below for connection details. Ensure all connections are secure before applying power.
Image: Detailed wiring diagram for the HT-10 controller.
- Temperature Sensor: Connect the black wires to the 'T' and 'VCC GND' terminals.
- Humidity Sensor: Connect the black and yellow wires to the 'H' and 'VCC' terminals.
- Exhaust Fan: Connect to terminals 1 and 2.
- Egg Turning Motor: Connect to terminals 3 and 4.
- Humidification Equipment: Connect to terminals 5 and 6.
- Heating Equipment: Connect to terminals 7 and 8.
- Power Input: Connect the main power supply to terminals 9 and 'L'.
After all connections are made, plug the controller into the appropriate AC220V/110V power outlet.
Operating Instructions
The HT-10 controller is designed for user-friendly operation with pre-configured settings for common incubation needs.
Image: Front panel layout and button functions of the HT-10 controller.
Panel Functions:
- Display: Shows current temperature (left) and humidity (right).
- Indicators: LEDs for HEAT, WET, TURN, ET (Egg Turning), Overtemperature, Heating, Humidification, and Celsius/Fahrenheit mode.
- Set Key (Gear icon): Used to enter setting mode.
- + Key (Up arrow): Used to increase values or navigate menus.
- - Key (Down arrow): Used to decrease values or navigate menus.
- Enter Key (Right arrow): Used to confirm selections or switch temperature units.
Temperature Unit Switching (Celsius/Fahrenheit):
The HT-10 supports both Celsius and Fahrenheit display modes. To switch between them:
- Press the Enter Key (right arrow button) to toggle the temperature unit.
- If the 'C/F' indicator light is on, the display is in Fahrenheit.
- If the 'C/F' indicator light is off, the display is in Celsius.
Image: Demonstrating Celsius and Fahrenheit display modes.
Factory Settings:
The controller comes with the following default settings for optimal incubation:
- Temperature: 38°C (100.4°F)
- Humidity: 60% RH
- Egg Turning Cycle: Every 90 minutes
- Egg Turning Duration: 180 seconds
- Ventilation Cycle: Every 120 minutes
- Ventilation Duration: 30 seconds
Image: HT-10 controller displaying factory settings.
These settings are generally suitable for most poultry eggs. Refer to specific incubation guides for different species if custom settings are required.
Maintenance
Regular maintenance ensures the longevity and accuracy of your HT-10 controller.
- Sensor Cleaning: Keep the temperature and humidity sensors clean. Dust or debris can affect accuracy. Use a soft, dry cloth for cleaning.
- Avoid Water Contact: Do not allow direct water contact with the sensors or the main unit.
- General Cleaning: Wipe the exterior of the controller with a slightly damp cloth if necessary. Ensure no liquid enters the device.
- Storage: When not in use, store the controller in a dry, cool place, away from direct sunlight and extreme temperatures.
Troubleshooting
If you encounter issues with your HT-10 controller, refer to the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Controller does not power on. | No power supply; incorrect voltage; loose wiring. | Check power connection; ensure correct voltage (AC220V/110V); verify all wiring connections are secure. |
| Inaccurate temperature/humidity readings. | Dirty sensors; damaged sensors; sensor not properly placed. | Clean sensors with a soft, dry cloth; ensure sensors are correctly positioned within the incubator; contact support if sensors appear damaged. |
| Egg turning or ventilation not working. | Loose wiring to motor/fan; motor/fan malfunction; incorrect settings. | Check wiring connections for egg turning motor and exhaust fan; verify settings for turning/ventilation cycles; test motor/fan independently if possible. |
| Temperature/humidity not stable. | Incubator insulation issues; heating/humidification equipment malfunction; external environmental factors. | Check incubator for drafts or poor insulation; ensure heating/humidification elements are functioning; minimize external temperature fluctuations. |
Specifications
Detailed technical specifications for the Hebuck HT-10 Egg Incubator Temperature Controller:
- Item Type: Incubator Controller
- Material: Plastic
- Size: Approx. 9.7 x 9 x 5.4 cm / 3.8 x 3.5 x 2.1 in
- Control Output Channels: 5 Channels (Temperature Control, Egg Turning, Over Temperature, Humidity Control, Alarm)
- Ambient Temperature: -10-60°C (14-105°F)
- Temperature Range: 0-99°C (0-110°F)
- Humidity Range: 0-99%RH
- Relative Humidity: <85%RH
- Humidity Accuracy: ±3%RH
- Temperature Accuracy: ±0.1°C / ±0.1°F
- Operating Voltage: AC220V/110V
- Display Type: Digital
- Included Components: Automatic Controller, Cable
Warranty and Support
For warranty information or technical support, please refer to the retailer or manufacturer's official website. Keep your purchase receipt for warranty claims. If you encounter issues not covered in this manual, please contact customer service for assistance.
