Introduction
This manual provides instructions for the PZL Replacement Projector Remote Control. This remote is designed to function as a direct replacement for specific projector models. It is important to note that this remote is not a universal remote. For proper functionality, your original remote control must be identical in appearance and button layout to this replacement unit.
Please read this manual thoroughly before use to ensure correct operation and to maximize the lifespan of your remote control.
Product Overview
The PZL Replacement Projector Remote Control is an infrared (IR) remote designed for ease of use with compatible projectors. It features a standard button layout for common projector functions.
Image 1: Front and side view of the PZL Replacement Projector Remote Control. The remote is black with clearly labeled buttons.
Key features include:
- Infrared (IR) Technology: Provides a stable signal for reliable control.
- Ergonomic Design: Comfortable to hold and operate.
- No Programming Required: Functions immediately after battery installation for compatible models.
Image 2: A hand holding the PZL remote control, pointing towards a projector displaying an image on a screen. This illustrates the remote in typical use.
Setup
The PZL Replacement Projector Remote Control requires two AAA batteries (not included) for operation. No programming or pairing is necessary.
1. Battery Installation
- Locate the battery compartment cover on the back of the remote control.
- Slide the cover downwards to open the compartment.
- Insert two 1.5V AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery compartment cover back into place until it clicks securely.
Image 3: A diagram illustrating the dimensions of the remote control and an open view of the battery compartment, showing where to insert two AAA batteries.
2. Initial Use
Once batteries are installed, the remote is ready for use with compatible projector models. Point the remote directly at the projector's IR receiver.
Image 4: A graphic emphasizing that no setup or pairing is required for the remote, highlighting its upgraded chip, lack of programming needs, and easy operation.
Operating Instructions
The remote control features a standard layout for common projector functions. Below is a general guide to the buttons:
- Power Button (⏻): Turns the projector on or off.
- Mute Button (🔇): Mutes or unmutes the projector's audio.
- Navigation Buttons (▲ ▼ ◀ ▶): Used to navigate menus and select options.
- OK Button: Confirms selections in menus.
- Volume Up/Down (🔊 🔉): Adjusts the projector's audio volume.
- Menu Button (☰): Accesses the projector's main menu.
- Return/Back Button (↩): Returns to the previous screen or menu.
- Playback Controls (⏮ ⏯ ⏭): For media playback functions (e.g., play, pause, skip).
Image 5: A hand holding the PZL remote control, highlighting the responsiveness of its buttons.
The remote utilizes advanced IR technology, providing a control range of approximately 26 feet (8 meters) and multi-angle control up to 120 degrees, allowing for flexible operation within a room.
Image 6: The PZL remote control emitting signal waves, illustrating its 26-foot long-range and 120-degree multi-angle control capabilities.
Compatibility
This PZL Replacement Remote Control is compatible with the following projector models, provided your original remote is identical in appearance and function:
- FUDONI Aurora P3
- Pericat 4K Portable
- GROVIEW JQ818C 4K
- Agreago V3
- Roconia 1080P G3W White
- HOMPOW C10
- VISSPL
- Sainellor AMX100
Important: This remote is specifically designed as a direct replacement. It will only function correctly if its button layout and infrared codes match your projector's original remote control. It is not a universal remote and does not support programming for other devices.
Maintenance
- Cleaning: Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
- Battery Replacement: Replace batteries when the remote's response becomes sluggish or stops working. Always replace both batteries at the same time with new ones of the same type.
- Storage: If the remote will not be used for an extended period, remove the batteries to prevent leakage and potential damage.
- Avoid Damage: Do not drop the remote, expose it to extreme temperatures, or immerse it in water.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote control is not working. |
|
|
| Remote works intermittently. |
|
|
| Specific buttons do not function. |
|
|
Note: If your projector model is not listed in the compatibility section or if your original remote was not identical to this unit, this replacement remote may not function correctly. Please confirm compatibility before purchase and use.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 0ae583a9-a8c4-4da0-85f7-67dea7efbda3 |
| Dimensions (L x W x H) | Approximately 5.43 x 1.50 x 0.67 inches |
| Item Weight | 1.92 ounces |
| Power Source | 2 x 1.5V AAA Batteries (not included) |
| Technology | Infrared (IR) |
| Color | Black |
| Max Supported Devices | 1 (Specific Projector) |
| Special Feature | Ergonomic Design |
Customer Support
For any questions regarding your PZL Replacement Projector Remote Control, including compatibility or operational issues, please contact our customer service. We aim to provide timely service within 24 hours.
Please refer to your purchase documentation for specific contact details or visit the PZL store on Amazon: PZL Store
