Product Overview
The Bewinner LED Digital Alarm Clock (Model Bewinner0sfx29r7wg-14) is designed for convenience and functionality, featuring a clear LED display, adjustable brightness, dual alarms, and a 12/24-hour time format. This manual provides detailed instructions for setup, operation, and maintenance.
Figure 1: Overview of the Bewinner LED Digital Alarm Clock's key features.
Package Contents
- 1 x LED Alarm Clock
- 1 x Power Cord (USB cable)
- 1 x Instruction Manual
Figure 2: The alarm clock and its USB power cable.
Setup
Powering the Device
The Bewinner LED Digital Alarm Clock is primarily outlet powered. A USB cable is included for power. An AC adapter is not included and must be supplied separately (5V 1A recommended).
- Connect the provided USB power cord to the DC 5V input port on the back of the alarm clock.
- Plug the other end of the USB cable into a compatible USB power adapter (not included) or a powered USB port.
- The clock will power on and display the time.
Battery Backup (Not for Primary Power)
The clock supports 3 x AAA batteries (not included) for memory backup. These batteries will retain time and alarm settings during a power outage but will not power the main display continuously. The display will only light up for 8 seconds when a button is pressed in battery mode.
- Open the battery compartment on the back of the clock.
- Insert 3 AAA batteries, ensuring correct polarity.
- Close the battery compartment.
Figure 3: Power input and battery compartment.
Operating Instructions
Controls Overview
The clock features several buttons on the top and back for setting time, alarms, and brightness. Refer to the diagram below for button identification.
Figure 4: Control buttons on the alarm clock.
Setting the Time
- Press and hold the TIME SET button on the back of the clock. The hour display will start flashing.
- Use the UP and DOWN buttons to adjust the hour.
- Press TIME SET again to move to minute adjustment. Use UP and DOWN to set the minutes.
- Press TIME SET a third time to confirm and exit time setting mode.
12/24 Hour Format
To switch between 12-hour and 24-hour time display, press the UP button during normal time display. The display will show "AM" or "PM" in 12-hour mode.
Figure 5: Switching between 12-hour and 24-hour time display.
Setting Alarms (Dual Alarm Function)
The clock supports two independent alarms. You can set different alarm days.
- Press and hold the ALARM SET button. The alarm hour will flash.
- Use UP and DOWN to set the desired alarm hour.
- Press ALARM SET again to set the alarm minutes. Use UP and DOWN.
- Press ALARM SET a third time to select alarm days (e.g., Mon-Sun, Mon-Sat, Mon-Fri, Single Day, Weekend). Use UP and DOWN to cycle through options.
- Press ALARM SET to confirm and exit.
- To set the second alarm, repeat the process.
Activating/Deactivating Alarms
To turn an alarm on or off, press the corresponding alarm toggle switch on the back of the clock.
Figure 6: Dual alarm settings and day options.
Snooze Function
When an alarm sounds, press the SNOOZE button (located on top) to activate a 5-minute snooze. The alarm will sound again after 5 minutes. To turn off the alarm completely, press any other button.
Adjusting Brightness
The clock has 3 adjustable brightness levels (Low, Medium, Bright) and an option to turn off the display. Press the LIGHT button (located on top) to cycle through the brightness settings.
Figure 7: Three levels of brightness adjustment.
Figure 8: Four levels of brightness adjustment including screen off.
Maintenance
- Clean the clock surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Avoid exposing the clock to extreme temperatures, direct sunlight, or high humidity.
- If using battery backup, replace AAA batteries annually or when the clock's memory function becomes unreliable.
- Ensure the USB power cable is not bent or damaged to maintain a stable power connection.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clock display is off. | No power or display brightness set to off. | Ensure USB power cable is securely connected to a working power source. Press the LIGHT button to adjust brightness. |
| Alarm does not sound. | Alarm is not activated or set incorrectly. | Check if the alarm toggle switch is ON. Verify alarm time and day settings. |
| Time/settings reset after power outage. | No backup batteries or batteries are depleted. | Install 3 new AAA batteries for memory backup. |
| Display is too dim/bright. | Brightness level needs adjustment. | Press the LIGHT button to cycle through brightness levels. |
| Incorrect time format (12H/24H). | Time format needs to be changed. | Press the UP button during normal time display to switch formats. |
Specifications
- Model: Bewinner0sfx29r7wg-14
- Material: ABS
- Display Type: LED
- Movement Type: Electronic
- Time Format: 12/24 Hours selectable
- Brightness Levels: 3 levels (Low, Medium, Bright) + Off
- Alarm Function: Dual Alarms with selectable alarm days
- Snooze Time: 5 Minutes
- Power Supply: 5V 1A (USB cable included, AC adapter not included)
- Battery Type (Backup): 3 x AAA Batteries (Not Included)
- Dimensions: Approx. 6.4 cm (2.5 in) x 3.5 cm (1.4 in) x 10 cm (3.9 in)
- Item Weight: 6.6 ounces (Approx. 187g)
Figure 9: Product dimensions.
Warranty and Support
Specific warranty information is not provided in the product details. For support or warranty inquiries, please refer to the seller's return policy or contact the manufacturer, Bewinner, directly through their official channels or the platform where the product was purchased.
The product is eligible for a 30-day refund/replacement return policy.