1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the YUANWIN Access Control System Kit. This system offers secure entry management through multiple methods including RFID cards, password access, remote controls, and smartphone app integration. It is designed for both residential and commercial applications, featuring a robust IP68 waterproof keypad and a high-strength 1200LB magnetic lock.
2. Product Components
The YUANWIN Access Control System Kit includes the following components:
Image: Overview of all components included in the YUANWIN Access Control System Kit.
- Access Control Keypad: IP68 waterproof metal touch keypad with backlit keys for visibility.
- 1200LB Magnetic Lock: High-strength electromagnetic lock for secure door closure.
- Power Supply Controller: Manages power distribution and system functions.
- Push to Exit Button: Durable zinc alloy button for internal door release.
- Remote Controls: Two wireless remote controls for convenient access.
- RFID Cards/Key Fobs: Multiple RFID key fobs for card-based access.
- Power Cable: For connecting the power supply.
- Mounting Hardware: Screws and anchors for installation.
3. Setup and Installation
3.1 Component Overview and Placement
The system is designed for both exterior and interior installation of various components. The keypad is typically installed on the exterior for access, while the exit button is placed on the interior. The magnetic lock is mounted on the door frame and door.
Image: Diagram illustrating typical placement of the access control keypad, magnetic lock, exit button, and power supply for outside and inside door access.
3.2 Keypad Installation
The access control keypad is IP68 rated for outdoor use. Mount it securely at a convenient height near the door.
Image: Close-up view of the IP68 waterproof metal touch keypad, highlighting its durable construction.
3.3 Magnetic Lock Installation
Install the 1200LB magnetic lock on the door frame and the armature plate on the door. Ensure proper alignment for maximum holding force.
Image: The 1200LB magnetic lock and its armature plate, with dimensions indicated for installation planning.
3.4 Power Supply Controller
The power supply controller converts AC 110V-240V to DC 12V (3A) for the system. It features various terminals for connecting all components.
Image: Rear view of the power supply unit, showing input and output terminals for wiring.
Image: Detailed diagram of the power supply controller, indicating input power, output connector, time delay adjustment potentiometer, and LED indicators.
The time delay adjustment potentiometer allows setting the lock release duration from 0 to 15 seconds. Rotate clockwise to increase the delay.
3.5 Exit Button Installation
The metal push-to-exit button is surface-mounted and designed for interior use.
Image: The zinc alloy push-to-exit button with its dimensions, suitable for surface mounting.
3.6 Wiring Diagram
Follow the wiring diagram carefully to connect all components to the power supply controller. Incorrect wiring can damage the system.
Image: Comprehensive wiring diagram showing connections between the access control keypad, exit button, power supply, and magnetic lock.
4. Operating Instructions
4.1 Keypad Access
To gain access using the keypad, enter your pre-programmed password followed by the '#' key. The lock will disengage for the set duration.
4.2 RFID Card Access
Present a registered RFID card or key fob to the keypad's reader area. The lock will disengage upon successful verification.
4.3 Remote Control Access
Press the button on the remote control to momentarily disengage the magnetic lock, allowing entry or exit.
4.4 Tuya App Remote Access
For remote access via the Tuya App, ensure the power supply controller is connected to your network and paired with the app. Use the app interface to remotely lock or unlock the door.
4.5 Exit Button Operation
From the inside, press the push-to-exit button to release the magnetic lock and open the door.
5. Maintenance
- Regularly inspect all wiring connections for signs of wear or damage.
- Keep the keypad surface clean from dirt and debris to ensure proper touch functionality.
- Check the magnetic lock and armature plate for proper alignment and ensure no obstructions prevent full contact.
- Test all access methods (keypad, RFID, remote, exit button) periodically to confirm functionality.
6. Troubleshooting
- System Not Powering On: Verify the power cable connection and check the power supply unit's input voltage. Ensure the power outlet is functional.
- Magnetic Lock Not Engaging/Disengaging: Check all wiring to the magnetic lock and power supply. Ensure the armature plate is correctly aligned with the electromagnet. Verify the power supply is providing 12V output.
- Keypad Not Responding: Check the keypad's power connection. Ensure no physical damage to the keypad.
- Remote Control Not Working: Check battery in remote. Ensure the remote control function is properly configured on the power supply controller.
- Tuya App Connectivity Issues: Verify your Wi-Fi network is active and the power supply controller is within range. Re-pair the device with the Tuya App if necessary.
- Exit Button Not Working: Inspect wiring from the exit button to the power supply controller.
7. Specifications
| Feature | Detail |
|---|---|
| Brand | YUANWIN |
| Model Number | YW-SP1203-T8-1200lb |
| Keypad Rating | IP68 Waterproof |
| Magnetic Lock Holding Force | 1200 lbs |
| Power Supply Input | AC 110V-240V (1A) 50Hz |
| Power Supply Output | DC 12V (3A) |
| Time Delay Adjustment | 0-15 seconds |
| Material | Stainless Steel (Keypad), Zinc Alloy (Exit Button) |
| Item Dimensions (L x W x H) | 11 x 9 x 4 inches |
| Item Weight | 11 Pounds |
| UPC | 769894489482 |
8. Warranty and Support
For warranty information and technical support, please refer to the documentation provided with your purchase or contact YUANWIN customer service directly. Keep your purchase receipt for warranty claims.
