M-VAVE WP-8 2.4G Wireless Guitar System User Manual

1. Introduction

This manual provides comprehensive instructions for the M-VAVE WP-8 2.4G Wireless Guitar System. This system is designed to provide a reliable and high-quality wireless connection for electroacoustic musical instruments such as guitars and basses. Please read this manual thoroughly before use to ensure proper operation and to maximize the lifespan of your device.

2. Safety Information

• Do not disassemble or modify the device.
• Keep the device away from water, moisture, and extreme temperatures.
• Use only the provided Type-C cable for charging.
• Avoid dropping or subjecting the device to strong impacts.
• Dispose of batteries and electronic components responsibly according to local regulations.

3. Package Contents

Verify that all items are present in your package:

• 1 x M-VAVE WP-8 Transmitter (TX)
• 1 x M-VAVE WP-8 Receiver (RX)
• 1 x Type-C Charging Cable
• 1 x User Manual (English)
• (Optional: 1 x Charging Case, if purchased with the "WP-8 with battery box" variant)

4. Product Overview

The M-VAVE WP-8 system consists of a transmitter (TX) and a receiver (RX) unit. Both units feature a rotatable 3.5mm/6.35mm plug for compatibility with various instruments and amplifiers.

Figure 1: M-VAVE WP-8 Transmitter (right) and Receiver (left) units. The transmitter is labeled 'TX' and features a guitar icon, while the receiver is labeled 'RX' and features a speaker icon. Both have LED indicators for status and battery.

Figure 2: M-VAVE WP-8 units demonstrating the 190-degree rotatable plug, allowing for flexible connection to various instrument jack orientations.

Key Features:

• 2.4GHz digital transmission.
• 24bit/48KHz sample rate for high-fidelity audio.
• Low latency: less than 6.7ms.
• Effective range: up to 30 meters outdoors, or 15 meters through walls.
• Dynamic range: >105dB.
• Frequency response: 20Hz-20KHz (+1dB/-3dB).
• Supports 3.5mm and 6.35mm plugs, rotatable up to 190 degrees.
• Allows up to 4 sets of devices to operate simultaneously in the same environment.

5. Setup and Connection

5.1 Charging the Units

Before first use, ensure both the transmitter and receiver are fully charged. Refer to Section 7 for detailed charging instructions.

5.2 Connecting the Transmitter (TX)

1. Identify the Transmitter unit (labeled "TX" with a guitar icon).
2. Rotate the plug to the desired angle.
3. Insert the transmitter's plug into the output jack of your instrument (e.g., guitar, bass).

5.3 Connecting the Receiver (RX)

1. Identify the Receiver unit (labeled "RX" with a speaker icon).
2. Rotate the plug to the desired angle.
3. Insert the receiver's plug into the input jack of your amplifier, audio interface, or pedalboard.

5.4 Powering On and Pairing

1. Press and hold the power button on both the Transmitter and Receiver units for a few seconds until the indicator lights illuminate.
2. The units should automatically pair. A solid green light on both units typically indicates a successful connection. If the lights are flashing, they are searching for a connection.
3. If pairing fails, try powering both units off and on again. Ensure they are within close proximity during the initial pairing process.

6. Operating Instructions

6.1 Channel Selection (for multiple sets)

The WP-8 system supports up to 4 sets of devices working simultaneously without interference. To change channels:

• With the unit powered on, briefly press the power button. The indicator light will change color or flash pattern to indicate the current channel.
• Cycle through the available channels until you find a clear one. Ensure both the transmitter and receiver are set to the same channel.

6.2 Status Indicators

• Green LED: Indicates a strong, stable connection and sufficient battery.
• Red LED: May indicate low battery or a connection issue. Refer to troubleshooting.
• Flashing LED: Typically indicates searching for a connection or charging status.

7. Charging

The M-VAVE WP-8 units can be charged via the included Type-C cable or, if applicable, using the dedicated charging case.

Figure 3: M-VAVE WP-8 Transmitter and Receiver units alongside their optional charging case. The case provides additional charges for extended use.

7.1 Charging with Type-C Cable

1. Connect the Type-C cable to the charging port on the Transmitter or Receiver unit.
2. Connect the other end of the cable to a USB power adapter (not included) or a computer's USB port.
3. The indicator light will show charging status (e.g., red while charging, off or green when fully charged).

7.2 Charging with Charging Case (if applicable)

1. Place the Transmitter and Receiver units into their respective slots in the charging case.
2. The charging case itself can be charged via its Type-C port.
3. The charging case can recharge the transmitter and receiver approximately twice, providing a total usage time of up to 12 hours (4 hours per charge + 2 recharges).

Note: The receiver and transmitter can operate continuously for up to 4 hours on a full charge.

8. Maintenance

• Cleaning: Use a soft, dry cloth to clean the units. Do not use liquid cleaners or solvents.
• Storage: When not in use for extended periods, store the units in a cool, dry place. Ensure they are fully charged before long-term storage to preserve battery health.
• Battery Care: Avoid fully discharging the batteries frequently. Recharge them regularly, even if not used often.

9. Troubleshooting

10. Specifications

11. Warranty and Support

For warranty information and technical support, please refer to the retailer or manufacturer's official website. Keep your proof of purchase for any warranty claims.

Manufacturer: TD.Shopthuyduongls