1. Introduction
This user manual provides comprehensive instructions for the ECONTROLLY DG11Q1-01 and DG11Q1-02 replacement AC remote controls. This remote is designed to be fully compatible with various Beko and Arcelik split-type room air conditioner units, including models DG11Q101 and DG11Q102. Please read this manual carefully before using the remote control to ensure proper operation and longevity.
2. Product Overview
The ECONTROLLY replacement remote control is an infrared device designed for ease of use, featuring an ergonomic design and a clear button layout for intuitive control of your air conditioner.
Figure 2.1: Front view of the remote control, displaying the LCD screen and all functional buttons.
Figure 2.2: Rear view of the remote control, highlighting the battery compartment cover.
Figure 2.3: Rear view with the battery compartment open, showing where to insert batteries.
Figure 2.4: Dimensions of the remote control, approximately 14 cm (5.51 in) in length and 5.8 cm (2.28 in) in width.
3. Setup
3.1 Battery Installation
- Locate the battery compartment on the back of the remote control.
- Slide the battery compartment cover downwards to open it.
- Insert two (2) new 1.5V AAA alkaline batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery compartment cover back into place until it clicks securely.
Important Note:
- This remote control requires no programming or pairing. Once batteries are installed, it is ready for use with compatible Beko and Arcelik air conditioner units.
- Do not mix old and new batteries, or different types of batteries.
- Remove batteries if the remote control will not be used for an extended period.
4. Operating Instructions
The remote control features a variety of buttons to manage your air conditioner's functions. Point the remote control directly at the air conditioner's receiver when operating.
| Button | Function |
|---|---|
| ⏻ POWER | Turns the air conditioner ON or OFF. |
| ▲ / ▼ | Adjusts the temperature setting (up/down). |
| MODE | Cycles through operating modes (e.g., Cool, Heat, Fan, Dry, Auto). |
| FAN | Adjusts fan speed (e.g., Low, Medium, High, Auto). |
| SUPER | Activates or deactivates rapid cooling/heating function. |
| SWING (⇌) | Controls horizontal louver swing. |
| SMART | Activates intelligent operating mode, often adjusting settings automatically for comfort. |
| IFEEL | Enables the remote control's built-in temperature sensor to provide more accurate room temperature readings to the AC unit. |
| TIMER OFF | Sets a timer for the air conditioner to turn off automatically. |
| CLOCK TIMER ON | Sets the current time and/or a timer for the air conditioner to turn on automatically. |
| DIMMER | Adjusts the brightness of the air conditioner's display panel. |
| SWING (⇕) | Controls vertical louver swing. |
| SLEEP | Activates sleep mode, which adjusts temperature and fan speed for comfortable sleep. |
| MUTE | Mutes the air conditioner's operational beeps or sounds. |
5. Maintenance
5.1 Cleaning the Remote Control
To clean the remote control, wipe it gently with a soft, dry cloth. Do not use liquid cleaners, abrasive cleaners, or chemical solvents, as these may damage the surface or internal components.
5.2 Battery Replacement
Replace batteries when the remote control's range decreases or if the display becomes dim. Always replace both batteries simultaneously with new 1.5V AAA alkaline batteries. Dispose of used batteries responsibly according to local regulations.
6. Troubleshooting
- Remote Control Not Responding:
- Ensure batteries are inserted correctly with proper polarity (+/-).
- Replace old batteries with new ones.
- Check if there are any obstructions between the remote control and the air conditioner's receiver.
- Ensure you are within the effective operating range (up to 10 meters) and pointing directly at the unit.
- No Programming Required: This remote control is a direct replacement and does not require any complex programming or pairing procedures. If it's not working, it's likely a battery or line-of-sight issue.
7. Specifications
| Model Number | DG11Q1-01-02-SENUO (Compatible with DG11Q1-01, DG11Q1-02, DG11Q101, DG11Q102) |
| Brand | ECONTROLLY |
| Connectivity Technology | Infrared |
| Controller Type | Button Control |
| Number of Buttons | 15 |
| Maximum Range | 10 Meters |
| Product Dimensions | 15 x 4 x 1.5 cm (approx. 5.9 x 1.6 x 0.6 inches) |
| Item Weight | 40 g (approx. 0.09 lbs) |
| Color | White |
| Special Features | Ergonomic design |
| Power Source | 2 x 1.5V AAA Alkaline Batteries (not included) |
8. Warranty and Support
For any questions or support regarding your ECONTROLLY replacement remote control, please contact the seller or manufacturer through your purchase platform. Please refer to your purchase documentation for specific warranty information.
For general inquiries or to report issues, please visit the product page on Amazon or contact Amazon customer service for assistance with your order.