ACEZUK M06 7000A Jump Starter with 150PSI Air Compressor User Manual

Introduction

Thank you for choosing the ACEZUK M06 7000A Jump Starter with 150PSI Air Compressor. This versatile device is designed to provide reliable vehicle jump-starting, tire inflation, and portable power for your electronic devices. Please read this manual thoroughly before use to ensure safe and optimal operation.

Package Contents

Verify that all items are present in your package:

• 1x ACEZUK M06 Jump Starter with Air Compressor
• 1x Smart Jumper Cable
• 1x Air Pump Hose
• 4x Gas Nozzles (various adapters)
• 1x USB-C Charging Cable
• 1x User Manual
• 1x Portable EVA Carrying Case

Important Safety Information

Always observe the following safety precautions to prevent injury or damage to the device:

• Do not use the air pump function continuously for extended periods. Allow the compressor to cool down if it becomes hot.
• Avoid over-inflating tires. If over-inflated, gently press the tire valve to release excess air.
• Ensure proper connection of jumper cables to the vehicle battery terminals (red to positive, black to negative).
• Do not short-circuit the jumper clamps.
• Keep the device away from children.
• Store in a cool, dry place.

Setup and Charging

Initial Charge

Before first use, fully charge the ACEZUK M06. Connect the provided USB-C charging cable to the device's Type-C input and a 5V/2A or higher USB power adapter (not included). The LCD screen will indicate the charging status.

Understanding the Display and Controls

• OK Button: Short press to turn on the jump starter. Long press (at least 3 seconds) to start inflation. Short press again to stop inflation.
• M Button: Press to switch between inflation modes (Car, Bicycle, Motorcycle, Ball).
• +/- Buttons: Adjust the preset pressure value. Short press to increase/decrease. Long press for rapid adjustment.
• LED Light: Long press the OK button (at least 3 seconds) to turn on the light. Short press to cycle through modes (light, strobe, SOS).

Operating Instructions

A. Vehicle Jump Starting

The ACEZUK M06 can reliably jump start 12V vehicles (all gasoline engines and up to 12.0L diesel engines) even in extreme temperatures (-20℃ to 60℃).

1. Insert Jumper Cable: Insert the smart jumper cable into the jump starter's port.
2. Connect Clamps: Connect the red clamp to the positive (+) terminal of the vehicle battery and the black clamp to the negative (-) terminal. Ensure a secure connection.
3. Start Vehicle: Start your vehicle's engine.
4. Remove Clamps: Once the vehicle starts, immediately remove the jumper clamps from the battery, then disconnect the cable from the jump starter.

The smart jumper cables include 8 protections: overheating, overcharge, over-discharge, over-voltage, short-circuit, reverse polarity, and anti-interference.

B. Tire Inflation

The built-in 150PSI air compressor can quickly inflate tires and other inflatables. It features a dual-cylinder technology for fast inflation (50LPM / 1.76 CFM).

1. Assemble Hose: Connect the air pump hose to the device.
2. Connect to Tire: Attach the hose to the tire valve.
3. Set Pressure: Use the 'M' button to select the desired inflation mode (car, bicycle, motorcycle, ball) or manual mode. Use the '+/-' buttons to set the target pressure. The LCD will display real-time pressure.
4. Start Inflation: Long press the 'OK' button to begin inflation. The compressor will automatically shut off when the preset PSI is reached.

Note:

• Do not use the air pump continuously for extended periods. If the compressor becomes hot, allow it to cool down for several minutes before resuming operation.
• Avoid over-inflating. If a tire is over-inflated, gently press the tire valve to release excess air.

C. Power Bank Functionality

The ACEZUK M06 features a 21800mAh battery capacity with dual USB outputs (5V/3A) and a Type-C input (5V/3A, 9V/2A), allowing you to charge mobile phones, tablets, and other devices.

• Connect your device's charging cable to one of the USB output ports on the ACEZUK M06.
• The device will automatically begin charging.

D. LED Flashlight

The 600-lumen LED light has three modes: constant light, strobe, and SOS. It is useful for nighttime repairs, outdoor activities, or emergencies.

• Long press the 'OK' button (at least 3 seconds) to turn on the LED light.
• Short press the 'OK' button to cycle through the light modes (constant, strobe, SOS).
• Long press the 'OK' button again to turn off the LED light.

Maintenance

• Charging: To maintain battery health, it is recommended to fully charge the device every 3-6 months, even if not in use.
• Cleaning: Wipe the device with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
• Storage: Store the ACEZUK M06 in its portable EVA carrying case in a cool, dry place, away from direct sunlight and extreme temperatures.
• Battery Life: For optimal performance, ensure the device is adequately charged before use, especially for jump-starting.

Troubleshooting

Specifications

Warranty and Support

ACEZUK provides a 2-year FREE warranty for the M06 Jump Starter with Air Compressor. We also offer lifetime technical support and 24/7 customer service.

For any questions, concerns, or technical assistance, please contact ACEZUK customer service through the retailer's platform or visit our official website.