Introduction
This manual provides instructions for the ASHATA Smart Ring Charging Case, designed to provide portable power for your compatible smart rings. This charging case is compatible with smart rings featuring a charging port, specifically models R02, R03, R06, R11M, R8, H01, and SR05. It is not suitable for smart rings with wireless charging functionality.
The charging case features a built-in 200mAh battery, capable of recharging your smart ring up to 10 times. Its compact design ensures portability and convenience for daily use and travel.
Image: The ASHATA Smart Ring Charging Case shown alongside a smart ring being worn on a finger, illustrating its purpose.
Package Contents
Before proceeding, please ensure all items are present in the package:
- 1 x ASHATA Smart Ring Charging Case
- 1 x USB Type-C Charging Cable
Image: The ASHATA Smart Ring Charging Case and its included USB Type-C charging cable.
Setup
1. Initial Charging of the Case
- Connect the provided USB Type-C charging cable to the charging port on the ASHATA Smart Ring Charging Case.
- Connect the other end of the USB cable to a compatible USB power adapter (not included) or a computer's USB port.
- The indicator light on the charging case will illuminate red, indicating that the case is charging.
- Once fully charged, the indicator light will turn green. A full charge typically takes approximately one hour.
Image: A close-up view of the ASHATA Smart Ring Charging Case, highlighting the Type-C charging port located on the side.
2. Inserting Your Smart Ring
- Open the lid of the charging case.
- Carefully place your compatible smart ring into the designated slot inside the case, ensuring the smart ring's charging port aligns with the magnetic charging pin within the case.
- Close the lid of the charging case.
Image: The ASHATA Smart Ring Charging Case shown open, revealing the interior design with the central charging pin for the smart ring.
Operating Instructions
Charging Your Smart Ring
- Ensure the charging case itself has sufficient power (indicator light is green or not flashing red).
- Place your smart ring into the charging case as described in the 'Setup' section.
- The smart ring will begin charging automatically. The indicator light on the charging case will show the status of the case's battery, not the ring's. Refer to your smart ring's own manual for its charging status indicators.
- The charging case can provide up to 10 full charges for your smart ring on a single full charge of the case's internal battery.
Image: The ASHATA Smart Ring Charging Case shown open with a smart ring correctly placed inside for charging.
Indicator Light Status
- Red Light: The charging case is currently being charged.
- Green Light: The charging case is fully charged.
- Flashing Red Light: The charging case's internal battery is low and requires recharging.
Maintenance
Cleaning
To maintain the charging case, wipe its exterior with a soft, dry, or slightly damp cloth. Avoid using harsh chemicals, abrasive cleaners, or excessive moisture, as these can damage the device.
Storage
When not in use for extended periods, store the charging case in a cool, dry place away from direct sunlight and extreme temperatures. It is recommended to fully charge the case before long-term storage and to recharge it every few months to preserve battery health.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Smart ring is not charging. | Charging case battery is low or depleted. | Recharge the charging case until the indicator light turns green. |
| Smart ring not properly seated in the case. | Ensure the smart ring's charging port aligns correctly with the magnetic pin inside the case. | |
| Smart ring is not compatible. | Verify your smart ring model is listed as compatible (R02, R03, R06, R11M, R8, H01, SR05) and uses a charging port, not wireless charging. | |
| Charging case indicator light is not working. | Charging cable or power source issue. | Try a different USB Type-C cable or a different USB power adapter. Ensure the power source is active. |
| Case battery completely depleted. | Leave the case connected to a power source for a few minutes to see if the light activates. |
Specifications
- Product Material: ABS
- Product Color: Black
- Charging Port: Type C
- Battery: 200mAh Lithium Ion Battery (Built-in)
- Compatible Models: For R02, R03, R06, R11M, R8, H01, R02, SR05, and smart rings with a charging port.
- Dimensions: Approx. 43 x 43 x 25mm / 1.7 x 1.7 x 1in
- Item Weight: 1.06 ounces
- Output Voltage: 5 Volts (DC)
Image: A diagram illustrating the dimensions of the ASHATA Smart Ring Charging Case, measuring 43mm in length, 43mm in width, and 25mm in height.
Warranty and Support
For warranty information and customer support, please refer to the documentation provided at the time of purchase or contact your retailer. ASHATA is the manufacturer of this product.