SOLIDEE U-shape Smart Bidet Toilet Seat User Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your SOLIDEE U-shape Smart Bidet Toilet Seat. Please read this manual thoroughly before use to ensure proper function and safety.

Safety Information

Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury.

• Ensure the power outlet is properly grounded.
• Do not immerse the unit in water or spray water directly onto the electrical components.
• Unplug the unit before cleaning or performing any maintenance.
• Do not allow children to operate the bidet seat without supervision.
• If the power cord is damaged, it must be replaced by the manufacturer or a qualified service agent.

Package Contents

Verify that all components are present before beginning installation:

• U-shape Smart Bidet Toilet Seat
• Remote Control
• Installation Hardware (screws, mounting plates)
• Water Supply Hose
• T-Valve Connector
• User Manual

Image: Contents of the SOLIDEE Smart Bidet Toilet Seat package, including the seat, remote, installation hardware, and hoses.

Setup and Installation

Pre-Installation Checklist:

• Ensure you have a standard U-shape toilet bowl.
• Verify access to a grounded electrical outlet (120V AC).
• Turn off the water supply to the toilet before starting.

Installation Steps:

1. Remove Existing Toilet Seat: Lift the hinge covers, unscrew the mounting bolts, and remove the old seat.
2. Install Mounting Plate: Place the bidet seat's mounting plate over the toilet bowl holes. Insert the rubber expansion nuts into the holes and secure the mounting plate with the provided bolts.
3. Connect T-Valve: Turn off the water supply to the toilet. Disconnect the existing water supply hose from the toilet tank. Install the T-valve onto the toilet tank's fill valve. Reconnect the original water supply hose to one end of the T-valve.
4. Connect Bidet Water Hose: Connect the provided bidet water supply hose from the T-valve to the water inlet on the side of the bidet seat. Ensure all connections are hand-tightened, then use a wrench for a final snug fit, being careful not to overtighten.
5. Slide Bidet Seat into Place: Align the bidet seat with the mounting plate and slide it forward until it clicks securely into place.
6. Restore Water Supply and Power: Slowly turn on the water supply to the toilet. Check for any leaks. Plug the bidet seat's power cord into a grounded electrical outlet.

Image: Detailed diagram illustrating the connection of the T-valve to the toilet tank and the bidet seat's water inlet.

Image: Product dimensions for the U-shape bidet seat, showing length and width measurements.

Operating Instructions

Remote Control Functions:

The bidet seat is primarily operated via the included remote control. Ensure the remote has batteries installed.

Image: The U-shape Smart Bidet Toilet Seat shown with its accompanying remote control.

Image: A detailed diagram illustrating the various buttons on the remote control and their corresponding functions, such as On/Off, water temperature, air temperature, seat temperature, and cleaning modes.

• On/Off: Press the power button to turn the unit on or off.
• Rear Cleaning: Activates the rear wash function.
• Female Cleaning: Activates the feminine wash function.
• Turbo Wash: Provides a stronger wash for thorough cleaning.
• Adjustable Water Temp: Cycles through water temperature settings (e.g., ambient, warm, warmer).
• Adjustable Air Temp: Adjusts the temperature of the warm air dryer.
• Adjustable Seat Temp: Cycles through seat temperature settings (e.g., off, low, medium, high).
• Adjustable Nozzle Position: Moves the nozzle forward or backward for optimal cleaning.
• Adjustable Water Pressure: Increases or decreases the water spray intensity.
• Warm Air Dryer: Activates the warm air drying function.
• Night Lighting: Toggles the soft LED night light on or off.
• ECO (Smart Power Saving): Activates energy-saving mode to reduce power consumption. Note: Heating functions may be reduced or off in ECO mode.
• Child Cleaning: Provides a gentle wash suitable for children.
• Stop: Stops all active bidet functions.

Side Knob Operation:

In addition to the remote, a side knob provides convenient access to basic cleaning and drying functions.

Image: A close-up view of the bidet seat's side knob, which allows for convenient control of cleaning and drying functions, and the integrated LCD display.

Key Features in Use:

Image: An illustration demonstrating the adjustable seat and air temperature features, showing warm air circulating around the seat.

• Adjustable Seat and Air Temperature: Use the remote to set your preferred seat and air dryer temperatures for maximum comfort. The LCD display will show the current temperature.
• Stainless Steel Nozzle: The self-cleaning stainless steel nozzle provides both rear and female washing functions. It automatically cleans itself before and after each use.
• Night Light: The soft LED night light illuminates the bowl, providing convenience during nighttime use without needing to turn on bright bathroom lights.
• LCD Display: The integrated LCD display shows real-time information such as water and seat temperatures, and active functions.

Image: A visual representation of the warm air dryer settings (Normal-Low-Medium-High) and warm seat temperature options (0°, 32°, 36°, 40° Celsius).

Image: A close-up of the self-cleaning stainless steel nozzle, accompanied by illustrations depicting its rear cleaning, female cleaning, and self-cleaning functions.

Image: The bidet seat with its soft LED night light illuminated, providing gentle light within the toilet bowl for nighttime use.

Maintenance

• Cleaning the Exterior: Wipe the exterior surfaces with a soft, damp cloth and mild, non-abrasive cleaner. Do not use harsh chemicals or abrasive pads.
• Nozzle Cleaning: The nozzle performs an automatic self-cleaning cycle. For additional cleaning, you can manually extend the nozzle (refer to remote control functions) and gently wipe it with a soft brush.
• Filter Cleaning: Periodically check and clean the water inlet filter to prevent blockages. Turn off the water supply and unplug the unit before accessing the filter.
• Long-Term Storage: If the unit will not be used for an extended period, drain all water from the unit and store it in a dry, temperate environment.

Troubleshooting

Specifications

Warranty and Support

For warranty information and customer support, please refer to the warranty card included with your product or contact SOLIDEE customer service directly. Keep your purchase receipt as proof of purchase.

Contact Information: Please visit the official SOLIDEE website or refer to your product packaging for the most up-to-date contact details for customer support.