1. Introduction
The ANYCUBIC Standard 3D Printer Resin Plus is a 405nm UV-curing photopolymer designed for high-precision and rapid 3D printing. This resin is compatible with 8K, 14K, and 16K capable LCD/DLP/SLA 3D printers. This manual provides essential information for safe handling, optimal use, and maintenance of the resin to achieve superior printing results.
Figure 1: ANYCUBIC Standard Resin Plus (Black, 1kg) and a sample 3D print.
2. Safety Precautions
WARNING: Resin is a chemical product. Always follow safety guidelines to prevent injury or adverse reactions.
- Wear Protective Gear: Always wear chemical-resistant gloves (nitrile or butyl rubber) and safety glasses to protect skin and eyes from direct contact with liquid resin.
- Ensure Adequate Ventilation: Use the resin in a well-ventilated area to minimize exposure to fumes. If possible, use an air purifier or work near an open window.
- Avoid Skin Contact: If resin comes into contact with skin, wash immediately and thoroughly with soap and water. Do not use alcohol or solvents to clean skin.
- Avoid Eye Contact: In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and seek medical attention.
- Do Not Ingest: Resin is harmful if swallowed. If ingested, do not induce vomiting. Rinse mouth and seek immediate medical attention.
- Keep Away from Children and Pets: Store resin in a secure location inaccessible to children and pets.
- Flammability: Keep resin away from open flames, sparks, and heat sources.
- Storage: Store resin in its original opaque bottle, tightly sealed, in a cool, dry, dark place, away from direct sunlight and UV light.
3. Setup and Preparation
3.1 Storage and Handling
- Before use, ensure the resin bottle is at room temperature (20-25°C / 68-77°F).
- Shake the resin bottle thoroughly for at least 1 minute before each use to ensure all components and color pigments are evenly mixed. Failure to do so may result in uneven coloring or print failures.
- Avoid exposing the resin to direct sunlight or any UV light source during storage and handling.
3.2 Pre-Printing Checks
- Ensure your 3D printer's build plate is clean and properly leveled according to your printer's instructions.
- Inspect the resin vat (FEP film) for any damage, dust, or cured resin particles. Clean if necessary.
- Pour the desired amount of resin into the clean resin vat. Do not overfill.
Figure 2: Pouring ANYCUBIC Standard Resin Plus into a vat, demonstrating its enhanced flowability.
4. Operating Instructions
4.1 Recommended Print Settings
Optimal print settings vary significantly depending on your specific 3D printer model, ambient temperature, and desired print detail. It is recommended to start with the resin manufacturer's suggested settings for your printer or consult online communities for proven profiles.
- Layer Height: Common layer heights range from 0.02mm to 0.05mm for detailed prints.
- Bottom Exposure Time: Typically 20-60 seconds for the initial layers to ensure strong bed adhesion.
- Normal Exposure Time: Generally 1.5-3.5 seconds per layer, depending on your printer's UV power and screen type. Conduct exposure tests to find the ideal time.
- Lifting Speed: A slower lifting speed (e.g., 40-60 mm/min) can help prevent print failures, especially for larger models.
4.2 Post-Processing
- Washing: After printing, carefully remove the model from the build plate. Wash the printed model in isopropyl alcohol (IPA) with a concentration of 95% or higher for 2-5 minutes to remove uncured resin. Use an ultrasonic cleaner or a wash and cure station for best results.
- Drying: Allow the model to air dry completely after washing, or use compressed air. Ensure no IPA residue remains.
- Post-Curing: Place the dried model in a UV curing chamber or under direct sunlight for final curing. Curing time varies but typically ranges from 2-10 minutes in a UV chamber or 30-60 minutes in direct sunlight. Over-curing can make the model brittle.
Figure 3: Example of a highly detailed 3D print, showcasing the accuracy of the resin.
Figure 4: Demonstrating the balanced strength and toughness of the cured resin.
5. Maintenance and Cleaning
5.1 Resin Vat Cleaning
- After printing, if you plan to store resin in the vat, cover it to prevent dust and light exposure.
- If changing resin colors or if the resin has been in the vat for an extended period, filter the resin back into its original bottle using a resin filter funnel.
- Clean the resin vat with IPA and a soft cloth. Avoid using abrasive materials that could scratch the FEP film.
5.2 Build Plate Cleaning
- After removing the print, clean the build plate with IPA to remove any resin residue.
- Ensure the build plate is completely dry before starting a new print.
5.3 General Cleaning
- Clean any spills immediately with IPA.
- Keep your work area tidy and free of uncured resin.
6. Troubleshooting Common Issues
| Problem | Possible Cause | Solution |
|---|---|---|
| Print fails to adhere to build plate | Insufficient bottom exposure time, cold resin, unlevel build plate, dirty build plate. | Increase bottom exposure time, ensure resin is at room temperature, re-level build plate, clean build plate thoroughly. |
| Partial or incomplete prints | Insufficient normal exposure time, FEP film damage, resin contamination, incorrect supports. | Increase normal exposure time, inspect/replace FEP film, filter resin, add more/stronger supports. |
| Brittle or soft prints | Over-curing during post-processing, under-curing, resin too old. | Adjust post-curing time, ensure adequate normal exposure, use fresh resin. |
| Uneven coloring or texture | Resin not thoroughly shaken. | Shake resin bottle vigorously for at least 1 minute before pouring into vat. |
| Strong odor during printing | Inadequate ventilation. | Ensure proper ventilation in the printing area. While this resin has low odor, good ventilation is always recommended. |
7. Product Specifications
| Attribute | Detail |
|---|---|
| Brand | ANYCUBIC |
| Model | Standard 3D Printer Resin Plus |
| Color (This Variant) | Black |
| UV Wavelength | 405nm |
| Viscosity (25°C) | 200 cps |
| Extensibility | 18.2% |
| Bending Modulus | 1599.33 MPa |
| Molding Accuracy | ±0.1mm |
| Item Weight | 2.59 pounds (1kg) |
| Package Dimensions | 9.41 x 3.98 x 3.9 inches |
| Special Features | Enhanced Resin Formula, High Compatibility, Low Odor |
Figure 5: Mechanical property comparison of Standard Resin+.
Figure 6: Recommendation index showing balanced performance.
7.1 Compatibility
The ANYCUBIC Standard 3D Printer Resin Plus is designed for high compatibility with most LCD and DLP 3D printers that utilize 405nm UV light for curing.
Figure 7: Wavelength compatibility and printer examples.
8. Disposal Guidelines
WARNING: Do not pour liquid resin directly into drains or dispose of it with household waste.
- Uncured Resin: Uncured liquid resin is considered chemical waste. It must be cured before disposal. Place uncured resin in a clear container under direct sunlight or a UV lamp until it solidifies.
- Cured Resin: Once fully cured and solid, resin can generally be disposed of as regular plastic waste according to local regulations.
- Contaminated IPA: IPA used for washing prints will contain dissolved resin. Cure the resin in the IPA by exposing it to UV light, then filter out the cured resin particles. The remaining IPA can often be reused or disposed of according to local chemical waste guidelines.
- Empty Bottles: Ensure resin bottles are completely empty and any residue is cured before recycling or disposing of them according to local regulations.
9. Support and Warranty
For further assistance, technical support, or inquiries regarding your ANYCUBIC Standard 3D Printer Resin Plus, please visit the official ANYCUBIC website or their Amazon store.
ANYCUBIC Official Store: Visit the ANYCUBIC Store on Amazon
Specific warranty information for consumable products like resin may vary. Please refer to the product packaging or contact ANYCUBIC customer service directly for details.
