1. Important Safety Information
Read all instructions carefully before assembly and use of this bunk bed. Failure to follow these instructions can result in serious injury.
- Weight Capacity: Each bed is designed to support a maximum weight of 700 lbs. Do not exceed this limit.
- Top Bunk Safety: The top bunk is equipped with guard rails. Ensure these are always securely in place. The top bunk is not suitable for children under 6 years of age.
- Mattress Requirements: Use only mattresses that comply with the recommended dimensions and thickness for bunk beds to ensure proper guard rail height.
- Ladder Use: Always use the provided ladder for access to the top bunk. Do not jump on or off the bunk bed.
- Assembly: Assembly must be performed by adults. Ensure all hardware is tightened securely before use and periodically check for tightness.
- Ventilation: Ensure adequate ventilation around the bunk bed.
- Prohibited Items: Do not attach or hang items to any part of the bunk bed that are not designed for use with the bed, such as hooks, belts, or ropes, as they can pose a strangulation hazard.
2. Package Contents
Verify that all components are present before beginning assembly. If any parts are missing or damaged, do not proceed with assembly and contact customer support.
- Headboards and Footboards (4 pieces)
- Side Rails (4 pieces)
- Ladder (1 piece)
- Guard Rails (2 pieces for top bunk)
- Bed Slats (multiple pieces for two beds)
- Hardware Pack (bolts, nuts, washers, screws, Allen wrench)
3. Setup and Assembly
Assembly is required for this bunk bed. It is recommended that two adults perform the assembly. Clear a spacious area for assembly and keep all hardware within reach.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a soft, clean surface to prevent scratching.
- Assemble Bed Frames: Attach the side rails to the headboards and footboards for both the upper and lower beds using the provided hardware. Ensure all connections are secure but do not fully tighten bolts until the entire frame is assembled.
- Install Bed Slats: Place the bed slats onto the support ledges of both bed frames. Secure the slats using the provided screws or connectors. Ensure even spacing for proper mattress support.
- Attach Guard Rails: For the top bunk, securely attach the guard rails to the side rails and head/footboards as indicated in the detailed assembly diagram.
- Attach Ladder: Securely attach the ladder to the designated side of the top bunk using the provided hardware. Ensure it is stable and does not wobble.
- Final Tightening: Once all components are assembled, go back and fully tighten all bolts and screws. Do not overtighten.
- Placement: Position the bunk bed against a wall to maximize stability and safety.

Image 1: Fully assembled Santino Twin Over Twin Bunk Bed in white finish.

Image 2: Front view of the bunk bed, showing the ladder and guard rails.

Image 3: Side view of the bunk bed, illustrating the paneled design.

Image 4: Detail of the ladder and its connection to the bunk bed frame.
4. Operating Instructions
Once assembled, the Santino Twin Over Twin Bunk Bed is ready for use. Adhere to the following guidelines for safe operation:
- Mattress Placement: Place standard twin-size mattresses on both the upper and lower bunks. Ensure the top mattress does not exceed the height of the guard rails.
- Ladder Safety: Always use the ladder to access the top bunk. Face the ladder when climbing up or down. Ensure hands and feet are clean and dry to prevent slipping.
- Weight Distribution: Distribute weight evenly on both bunks. Avoid concentrating weight in one small area.
- No Horseplay: Prohibit jumping, roughhousing, or playing on the bunk bed to prevent falls and injuries.
5. Maintenance
Regular maintenance will help prolong the life and safety of your bunk bed.
- Cleaning: Wipe surfaces with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners that could damage the finish.
- Hardware Check: Periodically (e.g., every 3-6 months) inspect all bolts, screws, and connections to ensure they are tight. Retighten as necessary.
- Structural Integrity: Check for any signs of wear, cracks, or damage to the wood frame or slats. Discontinue use if significant damage is found and contact customer support.
- Moving the Bed: If moving the bunk bed, lift it rather than dragging it to prevent stress on the joints and damage to flooring.

Image 5: Detail of the paneled headboard, illustrating the smooth white finish.

Image 6: View of the wooden slat system for mattress support.
6. Troubleshooting
If you encounter issues with your bunk bed, refer to the following common solutions:
- Squeaking Noises: Squeaking often indicates loose hardware. Re-tighten all bolts and screws. Ensure the bed is placed on a level surface.
- Wobbling: If the bed wobbles, check that all connections are fully tightened. Ensure the bed is on a flat, stable floor.
- Damaged Parts: If any part is damaged during assembly or use, do not attempt to repair it yourself if it compromises safety. Contact customer support for replacement parts.
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | SM700TTB |
| Product Dimensions | 79"L x 42"W x 65"H |
| Material | Wood |
| Color | White |
| Weight Capacity (Per Bed) | 700 lbs |
| Item Weight | 136 pounds |
| Assembly Required | Yes |

Image 7: Dimensional drawing of the bunk bed.
8. Warranty and Support
Warranty: This Picket House Furnishings product comes with a 1-Year Limited Manufacturer Warranty. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for warranty claims.
Customer Support: For missing parts, damaged components, or any questions regarding assembly or use, please contact Picket House Furnishings customer support. Refer to the contact information provided with your purchase or visit the official Picket House Furnishings website for assistance.
Online Resources: For additional support, assembly videos, or FAQs, please visit the official Picket House Furnishings website.