WANLUTECH MOT-31

Download PDF
Contents

WANLUTECH MOT-31 Singlemode OTDR Fiber Optic Tester

User Manual

1. Introduction

This manual provides detailed instructions for the safe and effective operation of the WANLUTECH MOT-31 Singlemode OTDR Fiber Optic Tester. This multi-functional device integrates OTDR, Optical Power Meter (OPM), Visual Fault Locator (VFL), Light Source (LS), Optical Loss Test (OLT), RJ45 Cable Test, and various network testing tools. Please read this manual thoroughly before using the device.

2. Safety Information

WARNING: Laser Radiation

  • Do not stare directly into the optical output ports when the device is active. Laser radiation can cause severe eye damage.
  • Avoid direct exposure to the laser beam.
  • Ensure all connections are secure before operating.
  • This device is not designed for testing live fiber. Connecting to live fiber may damage the device or interfere with active networks.
  • Only use the provided charger and accessories.
  • Keep the device dry and away from extreme temperatures.

3. Package Contents

Verify that all items listed below are included in your package:

  • 1x WANLUTECH MOT-31 OTDR Unit
  • 1x Packing Box
  • 1x Tool Bag
  • 1x Li-ion Battery (pre-installed or separate)
  • 1x Charger
  • 1x Type-C Power Cable
  • 1x OTDR Test Report
  • 1x Cable Tester Remote Kit
Image showing the complete package contents of the WANLUTECH MOT-31 OTDR Fiber Optic Tester.

Figure 3.1: WANLUTECH MOT-31 Package Contents

4. Product Overview

The WANLUTECH MOT-31 features a 4-inch touchscreen display and multiple ports for various testing functions.

Front view of the WANLUTECH MOT-31 OTDR Fiber Optic Tester with its main screen displaying various function icons and included accessories.

Figure 4.1: WANLUTECH MOT-31 Main Unit and Accessories

Top and bottom views of the WANLUTECH MOT-31 OTDR Fiber Optic Tester, highlighting ports and connectors like OTDR/LS, OPM, VFL, RJ45, USB-C, and Micro SD slot.

Figure 4.2: WANLUTECH MOT-31 Port Layout

Key Components:

  • OTDR/LS Port: For Optical Time Domain Reflectometer and Light Source functions.
  • OPM Port: For Optical Power Meter measurements.
  • VFL Port: For Visual Fault Locator.
  • LAN Port: For network testing functions (RJ45).
  • RJ45 Port: For RJ45 cable testing.
  • USB-C Port: For power input (DC5V/2A).
  • Micro SD Card Slot: For data storage and file management.
  • Power Button: To turn the device on/off.

5. Setup

5.1 Battery Installation

Before initial use, open the battery cover and remove any insulating paper piece from the battery compartment. Ensure the 3.7V/4000mAh Lithium Ion battery is correctly seated.

5.2 Initial Power On

Press and hold the power button to turn on the device. The 4-inch touchscreen will display the main menu.

5.3 Basic Settings

Navigate to the 'Settings' menu to configure language, date/time, brightness, volume, and other system preferences.

6. Operating Instructions

6.1 OTDR Test Function

The OTDR test function operates at wavelengths of 1310nm and 1550nm with dynamic ranges of 26dB and 24dB respectively. This model is not designed for testing live fiber.

Screenshot showing the OTDR Quick Setup and Parameters Set modes on the WANLUTECH MOT-31 display.

Figure 6.1: OTDR Quick Setup and Parameters Set Modes

  • Quick Setup Mode: Allows for rapid configuration of wavelength, distance range, pulse width, and measurement duration.
  • Parameters Set Mode: Provides advanced control for experienced users to define wavelength, distance range, pulse width, measurement mode, IOR, non-reflection threshold, and end threshold for precise curve results.
6.1.1 Event Map

The Event Map visualizes fiber optic link inspections, presenting information such as link length, connector type, fusion points, or break points in a graphical format. The Event Blind Zone is less than 1.6m, and the Attenuation Blind Zone is less than 8m.

Screenshot illustrating the Event Map and Threshold Setting interfaces for OTDR fiber link analysis.

Figure 6.2: OTDR Event Map and Threshold Setting

  • Initial Event: Represents the starting point of the fiber link.
  • Reflection Event: Indicates a connector or other reflective element.
  • Non-reflection Event: Shows a fusion splice or optical fiber bending, appearing as a drop in optical power.
  • End Event: Marks the terminal of the fiber. A normal end event shows a reflection peak.
6.1.2 Data Storage and Report Generation

Test results, including curves, event lists, parameters, and fiber link information, can be saved and viewed. The device supports generating test reports in SOR standard file format (PDF/EXCEL).

Screenshot displaying an OTDR event list and corresponding trace graph with detailed fiber link information.

Figure 6.3: OTDR Event List and Trace Graph

6.1.3 Multi-track Analysis

The device supports displaying up to four curves simultaneously for comprehensive analysis, allowing for more accurate evaluation of fiber characteristics.

Screenshot demonstrating multi-track analysis on the OTDR, showing multiple fiber curves for comprehensive evaluation.

Figure 6.4: Multi-track Analysis

6.1.4 File Management

Manage saved test reports, including curve trajectories, event lists, parameters, and fiber chains. Test reports are available in EXCEL and PDF formats. You can enable or disable automatic file naming, select the file format (OTDR or SOR), and define the file name type. Up to 4 curve files can be simultaneously selected for viewing.

Screenshots of the file management interface, showing options for saving, setting file formats, and viewing saved test reports.

Figure 6.5: File Management Interface

6.2 Optical Power Meter (OPM)

Connect the fiber to the OPM port to measure optical power linearly or non-linearly. This function is used for direct measurement of optical power and relative measurement of fiber link loss. Calibrated wavelengths include 850/1300/1310/1490/1550/1625nm, with a measurement range of -70 to +6dBm.

Diagram and screenshot illustrating the use of the Optical Power Meter (OPM) function and its display.

Figure 6.6: Optical Power Meter Operation

6.3 Visual Fault Locator (VFL)

The VFL function is used to determine fiber continuity and locate faults. It operates at a 650nm wavelength with a maximum test range of 8 KM. Exercise caution and avoid direct eye exposure to the red laser light.

Diagram and screenshot for the Visual Fault Locator (VFL) function, including a laser warning and output power.

Figure 6.7: Visual Fault Locator Operation

6.4 Light Source (LS)

Connect to the OTDR/LS port to use the device as a stable light source for engineering and maintenance of optical fiber communication and CATV systems. Available modulation modes include CW/270 Hz/330 Hz/1 kHz/2 kHz.

Diagram and screenshot explaining the Light Source (LS) function, showing wavelength and mode settings.

Figure 6.8: Light Source Operation

6.5 Optical Loss Test (OLT)

The OLT function measures the insertion loss of optical passive devices. Connect the OTDR/LS port and OPM port of the tester with short fiber optic patch cables. Initiate a 'Start Test' and, after power stabilization, click 'Set Parameter'. Then, connect the measured optical device to the OTDR/LS and OPM ports. The 'Relative Power' on the interface indicates the insertion loss value. Calibrate before each test for accurate results.

Diagram and screenshot detailing the Optical Loss Test (OLT) function, showing connection and measurement results.

Figure 6.9: Optical Loss Test Operation

6.6 RJ45 Cable TDR Test

This function tests the status of RJ45 cable pairs (open or short circuit) and measures their length up to 600 meters. One end of the network cable should be connected to the tester, and the other end should not be connected to other devices.

Diagram and screenshot demonstrating the RJ45 Cable TDR Test, showing cable pair status and length measurement.

Figure 6.10: RJ45 Cable TDR Test

6.7 UTP Cable Tester

Test the connection status of UTP cables and display results on the screen. This function supports detecting near-end, mid-end, and far-end fault points of the RJ45 cable plug.

Diagram and screenshot for the UTP Cable Tester, showing connection status and fault detection.

Figure 6.11: UTP Cable Tester

6.8 Cable Length Test

Measure the breakpoint position of open-circuit BNC, RJ45 network, and RJ11 cables. The maximum test length is 3000 meters. Short-circuit status will not display cable length. One end of the cable should be connected to the OTDR tester, and the other end should not be connected to other devices.

Diagram and screenshot illustrating the Cable Length Test for BNC, RJ45, and RJ11 cables, showing breakpoint position.

Figure 6.12: Cable Length Test

6.9 Network Test Tools

The device includes several network diagnostic tools:

Screenshots for IP Scan and FTP Server functions, showing network device discovery and file transfer setup.

Figure 6.13: IP Scan and FTP Server

  • IP Scan: Quickly finds the IP addresses of connected IP cameras or other network devices, supporting MAC address and manufacturer identification.
  • PING Test: A conventional network debugging tool used to verify connectivity and correct IP addresses of connected devices. Connect a network cable to the LAN port and enable the PING tool.
  • Screenshot of the PING Test interface, showing IP address, packet size, and test results.

    Figure 6.14: PING Test Interface

  • PPPOE: Used to detect whether broadband PPPOE dialing is normal.
  • LLDP: Detects capabilities, management IP addresses, device info, port info, and other information of switches. This function requires the switch to support the LLDP protocol.
  • Port Flashing: Connect a network cable to the tester's "LAN" port. If the OTDR tester and PoE switch are connected, the LAN port of the PoE switch will flash, aiding in quickly locating the connected Ethernet cable.
  • FTP: For copying and editing files from the SD card without using an SD card reader. Start the FTP service and enter the tester's FTP address in the computer's address bar.
Screenshots for LLDP, Port Flashing, and PPPOE functions, demonstrating network diagnostic tools.

Figure 6.15: LLDP, Port Flashing, and PPPOE Functions

7. Maintenance

7.1 Cleaning

  • Regularly clean the optical ports with appropriate fiber optic cleaning tools to ensure accurate measurements.
  • Wipe the device's exterior with a soft, dry cloth. Avoid abrasive cleaners or solvents.

7.2 Battery Care

  • Charge the battery fully before long-term storage.
  • If the device will not be used for an extended period, charge it every three months to maintain battery health.

7.3 Software Update

The device supports both local and online software updates to ensure optimal performance and access to new features.

Screenshot of the system update screen, offering local and online update options.

Figure 7.1: System Update Options

8. Troubleshooting

This section addresses common issues you might encounter with the WANLUTECH MOT-31.

ProblemPossible CauseSolution
Device does not power on.Low battery; Insulating paper still in battery compartment; Faulty charger.Charge the battery; Remove insulating paper; Try a different charger.
Inaccurate OTDR readings.Dirty optical connectors; Incorrect parameters set; Fiber not properly connected.Clean connectors; Verify OTDR parameters (IOR, pulse width, range); Reconnect fiber securely.
VFL light is dim or off.VFL function not activated; Low battery; Damaged VFL port.Ensure VFL is enabled in the menu; Charge battery; Contact support if port is damaged.
RJ45 cable test fails.Incorrect cable connection; Cable fault (open/short); Remote unit not connected (for UTP).Ensure correct connection; Check cable for physical damage; Connect remote unit for UTP test.
Touchscreen unresponsive.Temporary software glitch; Screen damage.Restart the device; If issue persists, contact support.

9. Specifications

FeatureSpecification
Model NumberMOT-31
OTDR Wavelength1310nm/1550nm
OTDR Dynamic Range26dB/24dB
Display4-inch Touchscreen
Optical Power Meter (OPM) Wavelengths850/1300/1310/1490/1550/1625nm
OPM Measurement Range-70 ~ +6dBm
Visual Fault Locator (VFL) Wavelength650nm
VFL Max Test Range8 KM
Light Source (LS) Wavelengths1310nm/1550nm
RJ45 Cable TDR Test LengthMax 600 meters
Cable Length Test (BNC, RJ45, RJ11)Max 3000 meters
Battery3.7V/4000mAh Lithium Ion (included)
Power InputDC5V/2A (Type-C)
Ethernet PortSingle Gigabit (10/100/1000Mbps adaptive)
ConnectorsSC/UPC
Dimensions7.99 x 6.5 x 2.95 inches
Weight1.87 Pounds
CertificationsCE, ETL, RoHS, UL

10. Warranty and Support

For any questions, technical assistance, or warranty inquiries regarding your WANLUTECH MOT-31, please contact the manufacturer directly. You can typically find contact information through your purchase platform or the official WANLUTECH website. Please provide your product model number (MOT-31) and purchase details when seeking support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.