Lefton Rotatable Bathroom Faucet BF2204 with Pop-up Bathroom Sink Drain Stopper D01

Introduction

This instruction manual provides detailed information for the installation, operation, and maintenance of your new Lefton Rotatable Bathroom Faucet BF2204 and accompanying Pop-up Bathroom Sink Drain Stopper D01. Please read this manual thoroughly before beginning installation or use to ensure proper function and longevity of your product. Retain this manual for future reference.

Safety Information

• Always turn off the main water supply before installing or servicing the faucet.
• Wear appropriate personal protective equipment, such as safety glasses and gloves, during installation.
• Ensure all connections are secure and watertight to prevent leaks.
• Do not overtighten nuts or connections, as this may damage the product.
• If you are unsure about any part of the installation process, consult a qualified plumber.
• Keep small parts away from children to prevent choking hazards.

Package Contents

Please verify that all components are present before beginning installation.

• Lefton Rotatable Bathroom Faucet BF2204 (Matte Black)
• Pop-up Bathroom Sink Drain Stopper D01 (Without Overflow)
• Hot & Cold Water Supply Lines (23.6 inches)
• Mounting Hardware (Gasket, Washer, Mounting Nut)
• Instruction Manual (This document)

Image: Main product components including the rotatable faucet and the pop-up drain stopper.

Specifications

Image: Detailed dimensions of the faucet, including mounting hole diameter (Min: 1.38" (35mm), Max: 1.5" (38mm)) and maximum deck thickness (1.9" (48mm)).

Image: Detailed dimensions of the pop-up drain stopper, showing its height and diameter measurements.

Setup and Installation

Before you begin, ensure you have the necessary tools: adjustable wrench, plumber's tape, screwdriver, and a basin wrench (if needed).

1. Prepare the Sink: Turn off the water supply to the sink. Clear the area under the sink. Remove any existing faucet and drain assembly. Clean the sink surface thoroughly.
2. Install the Faucet:
   • Insert the hot and cold supply lines into the faucet body. Hand-tighten only.
   • Place the rubber gasket on the bottom of the faucet body.
   • Insert the faucet into the single hole on the sink or countertop. Ensure the faucet is properly oriented.
   • From underneath the sink, slide the metal washer and then the mounting nut onto the threaded shank of the faucet.
   • Tighten the mounting nut securely with a basin wrench or adjustable wrench until the faucet is stable. Do not overtighten.
3. Connect Water Supply Lines:
   • Connect the hot water supply line (usually marked red or with a red stripe) to the hot water shut-off valve.
   • Connect the cold water supply line (usually marked blue or with a blue stripe) to the cold water shut-off valve.
   • Use plumber's tape on the threads of the shut-off valves for a watertight seal.
   • Tighten connections with an adjustable wrench.
4. Install the Pop-up Drain Stopper:
   • Disassemble the pop-up drain stopper by unscrewing the top cap and removing any washers or nuts.
   • Apply a bead of plumber's putty or silicone sealant around the underside of the drain flange (the top part that sits in the sink).
   • Insert the drain flange into the sink's drain hole from above.
   • From underneath the sink, slide the rubber washer, then the friction washer, and finally the mounting nut onto the drain body.
   • Tighten the mounting nut securely. Wipe away any excess plumber's putty or sealant.
   • Connect the drain tailpiece to the P-trap. Ensure all connections are tight.
5. Test for Leaks:
   • Slowly turn on the main water supply.
   • Check all connections for leaks. If leaks are present, tighten the connections slightly until they stop. Do not overtighten.
   • Run water through the faucet for a few minutes to flush out any debris.

Operating Instructions

• Water Flow and Temperature Control: The single handle controls both water flow and temperature.
  • Lift the handle to increase water flow.
  • Move the handle left for hot water and right for cold water.
  • Push the handle down to turn off the water.
• 360° Swivel Spout: The faucet spout can be rotated 360 degrees, allowing for flexible positioning and ease of use for various sink tasks.
• Rotatable Head: The head of the faucet can also be rotated and angled to direct water flow precisely where needed.
• Pop-up Drain Stopper: To close the drain, simply press down on the top of the drain stopper. To open, press down again.

Maintenance

• Cleaning: Clean the faucet regularly with a soft, damp cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the matte black finish.
• Aerator Maintenance: If water flow decreases, the aerator may be clogged. Unscrew the aerator from the end of the spout, clean any debris, and rinse it under water. Reattach securely.
• Leak Prevention: Periodically check all connections under the sink for any signs of leaks. Tighten connections if necessary.
• Drain Cleaning: The pop-up drain stopper can be easily removed for cleaning. Periodically remove it and clean any hair or debris that may have accumulated.

Troubleshooting

Warranty Information

Lefton products are manufactured to high-quality standards. For specific warranty details regarding your Lefton Rotatable Bathroom Faucet BF2204 and Pop-up Bathroom Sink Drain Stopper D01, please refer to the warranty card included with your purchase or contact Lefton customer support directly. Keep your proof of purchase for warranty claims.

Customer Support

If you have any questions, require technical assistance, or need to report an issue, please contact Lefton customer support:

• Email: customer@leftonhome.com (24/7 Service)
• Phone: 1 (601) 564 0548 (English Only, Mon. - Fri. 9:00 am - 6:00 pm PST)
• Online: Visit the official Lefton Store on Amazon for more information and products: Lefton Store

Image: A customer service representative wearing a headset and looking at a laptop, symbolizing customer support.