Introduction
This manual provides essential instructions for the safe and efficient setup, operation, and maintenance of your AQUANEAT 1 Gallon Betta Fish Tank. Please read thoroughly before use to ensure optimal performance and the well-being of your aquatic pets.
Safety Instructions
- Always unplug all electrical components before performing maintenance or cleaning.
- Ensure the power transformer for the LED light is compatible (5V 0.5A, 5V 1A, 5V 1.5A, or 5V 2A). Fast charging adapters are not supported.
- The water pump must be fully submerged in water to operate correctly and prevent damage.
- Place the aquarium on a stable, level surface away from direct sunlight or heat sources.
- Keep electrical cords organized and away from water to prevent hazards.
- This product is designed for indoor use only.
Package Contents
Image: Components included in the AQUANEAT 1 Gallon Fish Tank kit.
Verify that all components are present and undamaged before proceeding with setup:
- 1x 1 Gallon Fish Tank
- 1x Filter Sponge
- 1x Adjustable Water Pump
- 1x LED Hood (Note: Power transformer not included)
Setup Instructions
- Prepare the Tank: Rinse the tank and all components with clean water. Do not use soap or detergents, as residues can be harmful to aquatic life.
- Install the Filter Sponge: Place the filter sponge into the designated compartment within the tank's hidden filter system.
- Position the Water Pump: Secure the adjustable water pump inside the filter compartment, ensuring it is fully submerged once the tank is filled with water.
- Add Substrate and Decor (Optional): If desired, add a thin layer of aquarium-safe substrate and decorations. Rinse these thoroughly before adding them to the tank.
- Fill with Water: Carefully fill the tank with dechlorinated water to the appropriate level, leaving a small gap from the top.
- Connect the LED Hood: Place the LED hood on top of the tank. Connect the LED light's USB cable to a compatible 5V power transformer (not included).
- Power On: Plug in the water pump and the LED light transformer. Ensure the pump is operating and water is circulating.
Image: Illustration of the self-cleaning filtration system in operation.
Operating Instructions
LED Lighting System
Image: LED light controller and available lighting modes/brightness levels.
The LED hood features a 3-color lighting system with 10 adjustable brightness levels:
- Power Button: Press to turn the light on or off.
- Mode Button: Cycle through 3 lighting modes: All LEDs on (white, red, green, blue), White LEDs on, and Red+Green+Blue LEDs on.
- Brightness Adjustment: Use the '+' and '-' buttons to adjust the brightness level from 10% to 100%.
Water Pump Adjustment
Image: Adjustable water pump and other design features.
The water pump's flow rate can be adjusted to suit your aquatic environment. Refer to the pump's specific controls for increasing or decreasing water circulation.
Feeding
Utilize the convenient top feeding hole to feed your fish without needing to remove the entire lid. This minimizes disturbance to the tank environment.
Maintenance
Filter Cleaning
Regular cleaning of the filter sponge is crucial for maintaining water quality. If the pump stops working or the water flow decreases, it is time to clean the pump and filter sponge. Always unplug the pump before removal.
- Unplug the water pump from its power source.
- Carefully remove the water pump and filter sponge from the tank.
- Rinse the filter sponge thoroughly with old tank water (from a water change) or dechlorinated tap water to remove accumulated debris. Avoid using harsh chemicals.
- Clean any debris from the pump impeller and housing.
- Reassemble the pump and filter sponge, ensuring the pump is fully submerged when placed back into the tank.
- Plug the pump back in.
Water Changes
Perform partial water changes (25-50%) weekly to maintain optimal water parameters. Use a gravel vacuum to remove debris from the substrate during water changes. Always use dechlorinated water when refilling the tank.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water pump not working or weak flow. | Not fully submerged, clogged impeller, power issue. | Ensure pump is fully submerged. Unplug, clean impeller and housing. Check power connection. |
| LED light not turning on. | Power transformer issue, loose connection, faulty LED. | Check USB connection. Ensure transformer is compatible (5V, not fast charging). Try a different compatible transformer. |
| Water appears cloudy. | New tank syndrome, overfeeding, insufficient filtration, infrequent water changes. | Perform a partial water change. Reduce feeding. Clean filter. Ensure proper cycling for new tanks. |
| Water temperature is too high. | LED light generating heat, external heat source. | Consider reducing LED light usage or brightness. Ensure tank is not in direct sunlight or near a heater. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | PFT-001 |
| Tank Volume | 1 Gallon |
| Product Dimensions (L x W x H) | 7.9" x 5.9" x 5.9" |
| Material | Plastic |
| Special Feature | Shatter Resistant |
| LED Light Power Requirement | 5V 0.5A, 5V 1A, 5V 1.5A, or 5V 2A (Transformer not included) |
| Intended Use | Indoor |
Warranty and Support
For warranty information or technical support, please contact AQUANEAT customer service through the retailer where the product was purchased or visit the official AQUANEAT website. Please have your model number (PFT-001) and purchase date available when contacting support.