1. Product Overview
The Tissting 45A Brushless Electronic Speed Controller (ESC) is designed for 1/10 scale short-range RC trucks. This ESC offers robust performance, comprehensive safety features, and versatile compatibility for an enhanced remote control vehicle experience.
Key Features:
- Water and Dust Proof Design: Ensures consistent performance in various weather conditions, protecting internal components.
- External Programming Port: Allows for quick and easy connection to a programming card for customized settings.
- Comprehensive Safety Features: Includes low voltage cutoff, overheat protection, throttle signal loss safeguard, and motor lock guard for secure operation.
- Enhanced Performance Controls: Features proportional braking with four adjustable maximum braking force levels, eight drag braking force settings, and nine steps of acceleration tuning.
- Versatile Compatibility: Equipped with a built-in switch mode BEC, ensuring compatibility with various servo systems for 1/10 scale short-range trucks.

2. Setup Instructions
Proper setup is crucial for optimal performance and safety. Follow these steps to install and configure your ESC.
2.1 Component Identification

Familiarize yourself with the ESC components as shown in Image 2.1. Note the power input connector (T-plug), the three motor output wires, and the receiver connection cable with the integrated external programming port.
2.2 Wiring Connections
- Motor Connection: Connect the three motor wires from the ESC to your brushless motor. The order of connection may affect motor rotation direction; adjust if necessary during initial testing.
- Battery Connection: Connect your battery pack to the T-plug power input of the ESC. Ensure correct polarity.
- Receiver Connection: Plug the ESC's receiver cable into the throttle channel (usually channel 2) of your RC receiver.
- Servo Connection: If using additional servos, connect them to the appropriate channels on your receiver. The ESC's built-in BEC provides power to the receiver and servos.
2.3 Initial Calibration and Programming

After all connections are made, perform a throttle range calibration with your radio transmitter. Refer to your radio's manual for specific calibration steps. The external programming port (Image 2.2) allows for fine-tuning of ESC parameters such as braking force, acceleration, and battery cutoff voltage using a compatible programming card.
3. Operating Instructions
Once the ESC is properly installed and calibrated, you can begin operating your RC vehicle.
- Power On: Ensure your transmitter is turned on first, then connect the battery to the ESC. The ESC will emit a series of tones indicating successful initialization.
- Throttle Control: Use the throttle trigger on your transmitter to control the motor speed. Push forward for acceleration and pull back for braking/reverse.
- Braking: The ESC features proportional braking. Adjust the maximum braking force and drag braking force settings via the programming card to suit your driving style and track conditions.
- Acceleration: The acceleration curve can be adjusted in nine steps to provide a smoother or more aggressive power delivery.
- Power Off: Always disconnect the battery from the ESC first, then turn off your transmitter.

4. Maintenance
Regular maintenance helps ensure the longevity and reliable performance of your ESC.
- Cleaning: Due to its water and dust proof design, the ESC can withstand exposure to elements. However, it is recommended to clean the exterior with a soft brush or compressed air after use, especially in dirty or wet conditions, to prevent buildup around the cooling fan and heatsink.
- Inspection: Periodically inspect all wires and connectors for signs of wear, fraying, or corrosion. Ensure all connections are secure.
- Storage: When not in use, store the ESC in a dry, cool place away from direct sunlight and extreme temperatures. Disconnect the battery before storage.
5. Troubleshooting
If you encounter issues with your ESC, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not run or runs intermittently. | Loose connections, incorrect throttle calibration, motor lock guard activated. | Check all wiring connections. Re-calibrate throttle range. Inspect motor for obstructions. |
| ESC cuts off power during operation. | Low voltage cutoff, overheat protection activated. | Recharge or replace battery. Allow ESC to cool down. Check for proper ventilation. |
| No response from ESC. | No power, throttle signal loss, damaged ESC. | Ensure battery is connected and charged. Check receiver connection. Verify transmitter is on. |
| Motor runs in reverse. | Incorrect motor wire connection. | Swap any two of the three motor wires between the ESC and motor. |
If the product does not work due to missing parts, shipping damage, or defects, please contact Amazon promptly for return or replacement. Most issues can be resolved with proper setup and troubleshooting.
6. Specifications
Detailed technical specifications for the Tissting 45A Brushless Electronic Speed Controller.
| Feature | Specification |
|---|---|
| Item Type | RC Car Brushless ESC |
| Continuous Current | Fwd. 45A, Rev. 45A |
| Peak Current | Fwd. 135A, Rev. 135A |
| Resistive Value | 0.0012Ω |
| Applicable Model | 1:10 Road, Off Road, Buggy |
| Battery Compatibility | 4-9 NiMH Battery, 2-3S Li Ion Battery |
| Motor Limit (2S LiPo / 6 cell NiMH) | On Road: 3650 size or smaller, <6000Kv; Off Road Buggy: 3656 size or <4000KV |
| Motor Limit (3S LiPo / 9 cell NiMH) | On Road: 3656 size or smaller, <4000KV; Off Road Buggy: 3656 size or <3000KV |
| BEC Output | 5.85V 3A |
| Cooling Fan | Directly from battery, no adjustment required. Compatible with 2S and 3S Lipo. |
| Package Dimensions | 5.91 x 2.76 x 1.97 inches |
| Item Weight | 4.6 ounces |
| Model Number | Tisstingrkbw2h84ae |
| ASIN | B0DZVTFJZN |
7. Warranty and Support
This product is covered by a return policy that allows for refund or replacement within 30 days of purchase. For any issues or defects, please contact Amazon customer service directly to initiate a return or replacement process.
For further assistance or product inquiries, you may visit the Tissting Store on Amazon.