Valkyrie V360 Lite AIO CPU Liquid Cooler Instruction Manual

1. Introduction and Overview

The Valkyrie V360 Lite AIO CPU Liquid Cooler is designed to provide superior cooling performance for your computing tasks. It features an innovative mechanical design with a 90-degree rotatable pump top, visible circuit board, and addressable RGB LED lighting. Equipped with silent FDB fans and an advanced pump and radiator system, this cooler ensures efficient heat dissipation and quiet operation.

This manual provides detailed instructions for the proper installation, operation, and maintenance of your Valkyrie V360 Lite AIO CPU Liquid Cooler. Please read all instructions carefully before proceeding with installation.

Figure 1: Valkyrie V360 Lite AIO CPU Liquid Cooler with illuminated RGB fans.

2. Package Contents

Before beginning installation, verify that all components listed below are present in your package. If any items are missing or damaged, please contact customer support.

• Valkyrie V360 Lite AIO CPU Liquid Cooler (Radiator with 3x Pre-installed B12 ARGB Fans and Pump Head)
• Intel Mounting Hardware (Backplate, Retention Screws, Fastener Brackets, Nuts, Nut Socket)
• AMD Mounting Hardware (Backplate, Retention Screws, Fastener Brackets, Nuts, Nut Socket)
• Thermal Paste (Pre-applied on pump cold plate, plus an extra tube)
• Installation Guide

Figure 2: The Valkyrie V360 Lite AIO CPU Liquid Cooler retail packaging.

3. Setup and Installation

This section guides you through the step-by-step installation process. Ensure your system is powered off and unplugged before beginning.

3.1. Pre-Installation Checks

• Remove all protective stickers and plastic peels from the AIO cooler, including the radiator and pump head. Do not remove the thermal paste plastic protector from the cold plate yet.
• Verify that all pre-installed B12 ARGB fans are securely connected and daisy-chained.

Figure 3: Top view of the Valkyrie V360 Lite AIO CPU Liquid Cooler with fans in their default state.

3.2. Motherboard Preparation

The V-Lite AIO cooler is compatible with AMD AM4/AM5 and Intel LGA 1200/1700/1851/2011/2066 sockets. This guide uses an Intel LGA 1700 example. Refer to your motherboard manual for specific socket details.

1. Install the AIO Backplate: Align the corners of the backplate from behind the motherboard with the corresponding socket holes. Adjust the backplate alignment according to your platform (inner setting for LGA 1200, outer for LGA 1700/1851).
2. Secure Retention Screws: Use the Intel retention screws (larger threaded side down) to secure the backplate from the front side. Hand-tighten all four screws.
3. Install Fastener Brackets: Place the fastener brackets on top of the retention screws. Ensure correct orientation as indicated by the arrows on the brackets.
4. Tighten Nuts: Use the provided nuts and nut socket to tighten them down, securing the fastener brackets.

Figure 4: Included Intel and AMD mounting brackets for various CPU sockets.

3.3. Radiator Installation

Install the radiator onto a compatible sized panel within your PC case using the provided small radiator screws. For optimal cooling, consider mounting the radiator on the top panel if your case supports 360mm radiators.

Figure 5: Radiator mounted on the top panel of a PC case.

3.4. Pump Head Installation

1. Remove both the top and bottom portions of the magnetic pump cover.
2. Carefully remove the plastic cover on the cold plate to expose the pre-applied thermal paste.
3. Lower the pump head onto the CPU, aligning the two spring screws with the fastener brackets.
4. Tighten and secure the spring screws onto the fastener brackets.
5. Reattach both magnetic pump covers. The top cover can be flipped to any desired orientation.

Figure 6: Detailed view of the Valkyrie AIO pump head, showcasing its design.

Figure 7: The pump top can be rotated 90 degrees for optimal aesthetic alignment.

3.5. Cable Connections

Connect the pump head and radiator fans to your motherboard:

• Pump Head Connections: The pump head has two wires: a 3-pin ARGB connector and a 4-pin AIO pump connector. Connect the 3-pin ARGB connector to an available ARGB header on your motherboard. Connect the 4-pin AIO pump connector to your CPU_FAN or AIO_PUMP header on the motherboard.
• Radiator Fan Connections: The radiator fans also have two wires: a 3-pin ARGB wire and a 4-pin fan wire. Connect the 3-pin ARGB wire to another available ARGB header on your motherboard (or daisy-chain with the pump ARGB if supported). Connect the 4-pin fan wire to a CPU_OPT or SYS_FAN header.

4. Operating Instructions

Once installed and connected, the Valkyrie V360 Lite AIO CPU Liquid Cooler operates automatically, regulating fan and pump speeds based on CPU temperature to maintain optimal cooling performance. The RGB lighting can typically be controlled via your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) or a dedicated RGB controller if your motherboard does not support ARGB headers.

Figure 8: The cooler fully installed and operational within a PC build, showcasing its RGB effects.

5. Maintenance

Regular maintenance ensures the longevity and optimal performance of your AIO liquid cooler.

• Dust Removal: Periodically clean dust from the radiator fins and fan blades using compressed air or a soft brush. Ensure fans are not spinning during cleaning.
• Check Tubing and Connections: Inspect the tubing for any kinks or leaks. Ensure all cable connections (fan, pump, ARGB) are secure.
• Thermal Paste: The cooler comes with pre-applied thermal paste and an extra tube. Reapplication of thermal paste is generally not required unless the cooler is removed from the CPU.

6. Troubleshooting

If you encounter issues with your Valkyrie V360 Lite AIO CPU Liquid Cooler, refer to the following common troubleshooting steps:

• No RGB Lighting: Check if the 3-pin ARGB connector is securely plugged into the correct motherboard header. Ensure your motherboard's ARGB software is installed and configured correctly.
• Fans Not Spinning/Pump Not Working: Verify that the 4-pin fan/pump connectors are securely plugged into the appropriate headers (CPU_FAN, AIO_PUMP, SYS_FAN). Check your motherboard's BIOS/UEFI settings to ensure fan/pump headers are enabled and configured for proper operation.
• High CPU Temperatures: Ensure the pump head is securely mounted to the CPU and making good contact. Verify that the radiator fans are spinning and oriented correctly for airflow (pushing air through the radiator). Check for any obstructions to airflow within your PC case.
• Unusual Noises: Inspect fans for any obstructions or loose cables. If the pump is making unusual noises, ensure it is properly mounted and that there are no air bubbles trapped in the loop (this usually resolves itself with normal operation).

7. Specifications

8. Warranty and Support

The Valkyrie V360 Lite AIO CPU Liquid Cooler comes with a 5-year reliability warranty. For warranty claims, technical support, or further assistance, please refer to the official Valkyrie website or contact their customer service directly. Keep your proof of purchase for warranty validation.

For more information, visit the Valkyrie Store.