JURITS C7W

JURITS Walking Pad 2-in-1 User Manual

Model: C7W

1. Safety Information

Please read all instructions carefully before using the JURITS Walking Pad. Retain this manual for future reference.

2. Product Overview

The JURITS C7W Walking Pad is a versatile 2-in-1 fitness device designed for both walking and light jogging. Its compact and portable design makes it ideal for home and office use, especially under standing desks.

Key Features:

JURITS Walking Pad in use with a person walking on it under a standing desk.

Figure 2.1: JURITS Walking Pad in a home office setting, demonstrating its use under a standing desk.

Diagram showing the quiet motor, weight capacity, speed range, and low noise level of the JURITS Walking Pad.

Figure 2.2: Illustration of the JURITS Walking Pad's quiet motor, 265 lbs weight capacity, 0.6-3.8 MPH speed range, and less than 45 dB low noise operation.

3. Setup and Assembly

The JURITS Walking Pad comes largely pre-assembled. Follow these steps to prepare your device for first use.

Unboxing and Placement:

  1. Carefully remove the walking pad from its packaging.
  2. Place the unit on a firm, level surface. Ensure there is sufficient space around the device for safe operation.
  3. Inspect the walking pad for any signs of damage during transit.

Connecting Power:

  1. Locate the power input port on the walking pad.
  2. Connect the provided power cord to the walking pad and then to a standard grounded electrical outlet.
  3. Ensure the power switch (usually located near the power input) is in the 'ON' position. The LED display should illuminate.

Included Accessories:

Verify that all accessories are present in the packaging:

Image showing the JURITS Walking Pad and its included accessories: user manual, hex tools, remote, and lubricants.

Figure 3.1: Packaging Accessories for the JURITS Walking Pad.

4. Operating Instructions

The JURITS Walking Pad is operated primarily via its remote control. The LED display provides real-time workout data.

Remote Control Functions:

Starting a Workout:

  1. Ensure the walking pad is plugged in and the main power switch is ON.
  2. Stand on the walking pad.
  3. Press the 'ON/OFF' button on the remote control. The display will show a countdown (e.g., "3-2-1") before the belt starts moving at the minimum speed (0.6 MPH).
  4. Use the '+' and '-' buttons to adjust the speed to your desired pace.

During Your Workout:

Ending a Workout:

  1. To stop the walking pad, press the 'ON/OFF' button on the remote control. The belt will gradually slow down and stop.
  2. Once the belt has completely stopped, step off the walking pad.
  3. For extended periods of non-use, unplug the power cord from the wall outlet.
Person walking on the JURITS Walking Pad with an LED display showing speed, distance, time, and calories, and a remote control.

Figure 4.1: LED Display and Remote Control for the JURITS Walking Pad.

Image showing a person jogging on the JURITS Walking Pad with icons indicating speed range (0.6-3.8 MPH), low noise (<45db), 2.5 HP, and 265 LBS weight capacity.

Figure 4.2: JURITS Walking Pad in jogging mode, highlighting its performance metrics.

5. Maintenance

Regular maintenance ensures the longevity and optimal performance of your JURITS Walking Pad.

Cleaning:

Belt Lubrication:

The running belt requires periodic lubrication to reduce friction and extend its lifespan. Use the provided lubricant.

  1. Unplug the walking pad.
  2. Carefully lift the edge of the running belt.
  3. Apply a small amount of lubricant (a few drops) to the center of the deck, underneath the belt.
  4. Plug in the walking pad and run it at a low speed (e.g., 0.6 MPH) for 1-2 minutes to distribute the lubricant evenly.
  5. Lubricate every 3-6 months, or after approximately 50 hours of use, depending on usage frequency.

Belt Adjustment:

If the running belt becomes off-center or slips, it may need adjustment. Use the hex tools provided.

Diagram showing the 5-layer anti-slip running belt with shock absorbing points for knee and ankle protection.

Figure 5.1: Cross-section view of the comfortable 5-layer anti-slip walking belt with shock absorption.

6. Troubleshooting

If you encounter issues with your JURITS Walking Pad, refer to the table below for common problems and solutions.

ProblemPossible CauseSolution
Walking pad does not start.Power cord not connected; Main power switch off; Remote control battery low.Ensure power cord is securely plugged in. Turn on the main power switch. Replace remote control batteries.
Belt slips or hesitates.Belt too loose; Insufficient lubrication.Adjust belt tension (see Maintenance section). Apply lubricant to the running deck (see Maintenance section).
Belt drifts to one side.Belt is off-center.Adjust belt centering (see Maintenance section).
Unusual noise from the unit.Loose components; Lack of lubrication; Debris under belt.Check for and tighten any loose screws. Lubricate the belt. Clean underneath the belt. If noise persists, contact support.
Display not working.Power issue; Loose connection.Check power connection. Ensure main power switch is on. If problem persists, contact support.

If the problem persists after attempting these solutions, please contact JURITS customer support.

7. Specifications

8. Warranty and Support

Warranty Information:

The JURITS Walking Pad C7W comes with a lifetime warranty, ensuring long-term reliability and peace of mind for our customers.

Customer Support:

JURITS is dedicated to providing superior quality products and excellent customer service. If you have any questions, concerns, or require assistance with your walking pad, our professional support team is available to help.

Contact JURITS customer support for assistance.

Related Documents - C7W

Preview BACnet Conformance Certificate for 75F HyperStat - BTL-31060
Official BACnet Conformance Certificate (BTL-31060) for the 75F HyperStat product, confirming compliance with ISO 16484-5 standards. Includes product models, firmware version, vendor details, and validity period.
Preview 75F HyperStat BACnet Controller Product Listing (BTL-31060)
Official product listing for the 75F HyperStat BACnet controller, detailing its model numbers, firmware version, device profiles, supported BIBBs, object types, data link options, and character set support as tested by BACnet Testing Laboratories (BTL).
Preview HanYoung NUX Product Catalog by MELTAS
A comprehensive catalog of HanYoung NUX industrial automation and electronic components, distributed by MELTAS. Features a wide range of products including timers, counters, sensors, switches, and control devices with model numbers.