Andeman 4000A Jump Starter (Model EP-166) User Manual

1. Introduction

Thank you for choosing the Andeman 4000A Jump Starter, Model EP-166. This device is designed to provide reliable power for jump-starting vehicles and charging electronic devices. Please read this manual thoroughly before use to ensure safe and optimal operation.

1.1. What's in the Box

• Epower-166 Jump Starter Unit x1
• Smart Clamps x1
• Type-C Charging Cable x1
• User Manual x1
• Storage Box x1

Image: All components included in the Andeman Jump Starter package, laid out for clear visibility.

2. Safety Precautions

Your safety is paramount. This device incorporates advanced safety features, but proper handling is crucial. The Andeman EP-166 is UL Certified, ensuring it meets stringent safety standards.

2.1. Integrated Safety Protections

The intelligent safety terminals feature 10 advanced protections:

• Overload Protection
• Spark Protection
• Reverse Charge Protection
• Reverse Polarity Protection
• Over Current Protection
• Low Temperature Protection
• Over Charge Protection
• Short Circuit Protection
• Over Voltage Protection
• High Temperature Protection

Image: An internal view highlighting the 10 advanced safety protections integrated into the Andeman Jump Starter for secure operation.

2.2. Environmental Considerations

• Temperature Range: The device is engineered to operate in extreme temperatures, from -20°C (-4°F) to 60°C (140°F).
• Waterproof Rating: With an IP65 waterproof rating, the unit is resistant to rain and splashes. Avoid submerging the device in water.
• Durability: The design is drop-proof and sand-proof for enhanced durability in various environments.

3. Setup

3.1. Charging the Jump Starter

Before initial use, fully charge the jump starter. It features Type-C 3.0A Quick Charging technology, allowing a full charge from 0% to 100% in approximately 1.8 hours. Each complete charge provides up to 80 jump-starts.

• Connect the provided Type-C charging cable to the jump starter's input port.
• Connect the other end of the cable to a suitable USB power adapter (not included).
• The LED display will show the charging progress.

Image: The jump starter being fast-charged via its Type-C port inside a vehicle, showing its quick recharge capability.

4. Operating Instructions

4.1. Jump Starting a Vehicle

1. Ensure the jump starter is adequately charged.
2. Insert the smart clamps cable into the jump starter's dedicated port.
3. Connect the red (+) clamp to the positive terminal of the vehicle's battery.
4. Connect the black (-) clamp to the negative terminal of the vehicle's battery.
5. Check the indicator light on the smart clamps. A solid green light indicates it's safe to proceed. If it flashes red or beeps, refer to the troubleshooting section.
6. Start the vehicle's engine.
7. Once the vehicle starts, remove the smart clamps from the vehicle battery within 30 seconds.
8. Disconnect the smart clamps cable from the jump starter.

Image: The Andeman Jump Starter connected to a car battery, illustrating the ease of use for jump-starting a vehicle.

4.2. Using as a Power Bank

The 20000mAh capacity allows the jump starter to function as a power bank for various electronic devices.

• Connect your device's charging cable to one of the available USB output ports (USB-A: 2.1A; 5V/9V/12V or USB-B: 3A; 5V/2.1A).
• The dedicated Type-C port can also charge laptops at speeds comparable to their original adapters.
• The LED display will show the remaining battery percentage.

Image: The 20000mAh power bank feature in action, charging a laptop, smartphone, tablet, headphones, and smartwatch.

4.3. Using the LED Flashlight

The built-in ultra-bright LED flashlight offers three lighting modes:

• Flashlight: For general illumination (e.g., inspecting an engine, changing a tire).
• SOS: A life-saving signal light for emergencies.
• Strobe: A traffic warning light to alert oncoming traffic.

To activate and cycle through the modes, press the dedicated flashlight button on the unit.

Image: Illustration of the three versatile LED lighting modes: standard flashlight, SOS signal, and strobe, useful for various emergencies.

5. Maintenance

5.1. Charging and Storage

• Recharge the jump starter every 3-6 months if it is not in regular use to maintain battery health.
• Store the device in its protective storage box in a cool, dry place, away from direct sunlight and extreme temperatures.

6. Troubleshooting

The smart clamps provide visual and audible feedback to help diagnose common issues:

7. Specifications

8. Official Product Videos

9. Warranty and Support

For detailed warranty information and customer support, please refer to the user manual included in your product package. You may also contact Andeman customer service directly via email: andeman@andeman.com.