AUSOM Leopard DT1 Pro Electric Scooter User Manual

Introduction

The AUSOM Leopard DT1 Pro Electric Scooter is designed for adults seeking powerful performance, advanced safety features, and supreme riding comfort. This manual provides essential information for the safe operation, assembly, maintenance, and troubleshooting of your scooter. Please read this manual thoroughly before your first ride to ensure optimal performance and safety.

Key features include dual 1000W motors for speeds up to 41 mph, an 18.2Ah battery offering up to 47 miles range, dual braking systems (ZOOM hydraulic disc brakes and EABS), SUV-level swingarm suspension, a smart LCD display, and a comprehensive lighting system with turn signals.

Safety Information

WARNING: Always wear a helmet and appropriate safety gear when riding. Obey all local traffic laws and regulations. Do not ride in wet conditions or on slippery surfaces. Always perform a pre-ride inspection.

• Familiarize yourself with all controls and features before riding.
• Ensure all bolts and fasteners are tightened before each ride.
• Check tire pressure regularly.
• Do not exceed the maximum weight limit of 143 pounds.
• Avoid riding in heavy rain or through deep puddles to prevent damage to electrical components.
• Use turn signals and lights to enhance visibility, especially at night.
• Maintain a safe distance from other vehicles and pedestrians.

Package Contents

Upon opening the box, verify that all components are present and undamaged. The standard package includes:

• AUSOM Leopard DT1 Pro Electric Scooter (main unit)
• User Manual
• Power Adapter
• Power Cable
• Tool Kit
• NFC Card (for security lock system)

Setup and Assembly

Follow these steps to assemble your AUSOM Leopard DT1 Pro Electric Scooter:

1. Unfold the Stem: Carefully lift the scooter from its packaging. Open the kickstand to allow the scooter to stand upright. Unfold the stem until it locks securely into place.
   

   Image: The AUSOM Leopard DT1 Pro Electric Scooter shown both folded for transport and fully unfolded for riding, highlighting its compact design and readiness for use.

2. Attach the Handlebar: Place the handlebar onto the top of the stem. Ensure the clip is centered.
3. Install the Display: Position the smart LCD display on the handlebar. Align the four M5 screws with the screw holes in the stem clip and tighten them securely to fasten the display and handlebar.
4. Attach Motor Nut Caps: Secure the four motor nut caps to the front and rear motor nuts as shown in the assembly video.

Operating Instructions

Power On/Off and Security Lock

To power on the scooter, press the power switch for 3 seconds. The LCD display will show "Card". Place the NFC card over the NFC detection area on the display to activate the scooter. The display will light up, indicating it's ready for use. To power off, press and hold the power button for 3 seconds.

Adjusting Speed Modes

The scooter features three riding modes: ECO, SPORT, and RACE. After exiting PARK mode (by pressing the Plus button), use the Plus (+) or Minus (-) buttons on the control panel to switch between these modes. Each mode offers different speed and power characteristics:

• ECO Mode: For maximum range and energy efficiency.
• SPORT Mode: Balanced performance for daily commuting.
• RACE Mode: Full power and speed, reaching up to 41 mph.

Image: A rider demonstrating the power and speed of the AUSOM Leopard DT1 Pro, highlighting its dual 1000W motors and maximum speed capabilities across different modes.

Lighting System and Turn Signals

The scooter is equipped with a comprehensive lighting system for enhanced visibility and safety:

• Headlight: Press the Plus button for 3 seconds to turn the ultra-bright front headlight on or off.
• Brake and Tail Lights: Safety brake and warning tail lights activate automatically when braking.
• Turn Signals: Push the turn signal light switch to the left or right to activate the corresponding turn signal. Push the switch in the same direction again to turn it off.

Image: The AUSOM Leopard DT1 Pro Electric Scooter with its front headlight and side lights illuminated, demonstrating its visibility features for night riding.

Horn

Press the horn button located on the left handlebar to alert others of your presence.

Single/Dual Motor Mode

Short press the DDM button to switch between Single and Dual Motor modes, allowing for power conservation or full power as needed.

Folding and Transport

The scooter is designed for easy folding and transport. Locate the folding mechanism on the stem, release the latch, and fold the stem down towards the deck until it locks. This compact design makes it convenient for storage or carrying.

Image: A visual guide illustrating the simple steps required to fold the AUSOM Leopard DT1 Pro Electric Scooter, making it compact for storage or transportation.

Charging

The scooter features dual charging inputs, allowing for a full charge in approximately 4-5 hours. It also has dual charging outputs (USB-B and Type-C) to power your devices on the go.

Image: The AUSOM Leopard DT1 Pro Electric Scooter with a graphic overlay illustrating its impressive battery capacity and maximum range of up to 47 miles.

Riding Performance and Features

The AUSOM Leopard DT1 Pro is built for diverse terrains and high performance:

• Dual 1000W Motors: Provides exceptional power and acceleration for various riding conditions.
• Dual Braking Systems: Equipped with ZOOM hydraulic disc brakes and an EABS system for precise and responsive stopping power.
• SUV-Level Suspension: Features a swingarm design that effectively absorbs shocks and vibrations, ensuring a smooth ride even on rough terrain.
• 10"x3" Off-Road Tires: Thick pneumatic tires designed to effortlessly navigate various obstacles and provide excellent grip.

Maintenance

Regular maintenance is crucial for the longevity and safe operation of your scooter:

• Cleaning: Wipe down the scooter with a damp cloth after each ride. Avoid using high-pressure water jets directly on electrical components.
• Tires: Check tire pressure weekly. Recommended pressure is typically found on the tire sidewall. Inspect tires for wear and tear.
• Brakes: Regularly check brake lever tension and brake pad wear. Adjust or replace as needed.
• Battery: Charge the battery fully after each use, especially if storing for an extended period. Do not allow the battery to fully discharge.
• Fasteners: Periodically check and tighten all screws and bolts, especially those on the handlebars, stem, and wheels.
• Storage: Store the scooter in a cool, dry place away from direct sunlight and extreme temperatures.

Troubleshooting

Here are some common issues and their potential solutions:

If the issue persists after attempting these solutions, please contact AUSOM customer support for further assistance.

Specifications

Warranty and Support

The AUSOM Leopard DT1 Pro Electric Scooter comes with a limited warranty. Please refer to the warranty card included in your package for specific terms and conditions. For technical support, replacement parts, or any inquiries not covered in this manual, please contact AUSOM customer service through their official website or the retailer where you purchased the product.

For more information, visit the official AUSOM Store on Amazon.