Introduction
Thank you for choosing the atomberg Renesa 400mm Table Fan. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your new fan. Please read it thoroughly before use and retain it for future reference.
Important Safety Information
- Always ensure the fan is placed on a stable, flat surface to prevent tipping.
- Do not insert fingers or any objects through the fan grille when the fan is operating.
- Keep the fan away from water or other liquids. Do not operate in wet environments.
- Unplug the fan from the power outlet before cleaning, maintenance, or when not in use.
- Do not operate the fan with a damaged cord or plug. Contact customer support for repairs.
- This appliance is for indoor use only.
- Ensure the power supply voltage matches the rating label on the fan.
What's in the Box
Upon opening the package, verify that all the following components are present:
- Front grill
- Grill belt
- Rear grill
- Base
- Motor assembly
- Set of blades
- Remote control
- Batteries (for remote)
- User manual
- Warranty card
Setup and Assembly
The atomberg Renesa Table Fan is designed for easy assembly. Follow these general steps:
- Attach the Base: Securely connect the fan's main body (motor assembly) to the base. Ensure it clicks into place or is fastened according to the specific design.
- Install the Rear Grill: Place the rear grill onto the motor assembly, aligning it correctly.
- Mount the Blades: Carefully attach the fan blades to the motor shaft. Ensure they are firmly secured.
- Attach the Front Grill: Position the front grill over the blades and secure it to the rear grill using the grill belt or clips provided. Ensure the grill is fully closed and locked for safety.
- Insert Remote Batteries: Open the battery compartment on the remote control and insert the provided batteries, observing polarity.
Image: Overview of the fan's control features, including the remote, digital speed display, and feather touch button.
Operating Instructions
Your atomberg Renesa Table Fan can be operated using either the included remote control or the feather-touch button on the fan unit.
Remote Control Functions
Image: Detailed view of the remote control and its various functions.
- Power Button (●): Press to turn the fan ON or OFF.
- Speed Control (1-6): Use the numbered buttons to select one of the 6 available fan speeds. The digital display on the fan will show the current speed.
- Boost Mode: Activates the highest fan speed for maximum airflow.
- Timer Mode: Allows you to set the fan to switch off automatically after a pre-set number of hours.
- Sleep Mode: Gradually decreases the fan's speed every two hours for comfortable sleep.
- Oscillation Control (OSC): Toggles the 90° automatic swing function ON or OFF.
Feather-Touch Button Operation
The feather-touch button on the fan unit allows for basic control:
- Press once to turn ON/OFF.
- Subsequent presses cycle through speed settings.
- Long press may activate/deactivate oscillation (refer to specific product behavior).
Adjusting Airflow Direction
Image: Illustration of the fan's 90-degree oscillation and 30-degree manual tilt capabilities.
- Automatic Oscillation: Use the "OSC" button on the remote to activate or deactivate the 90° horizontal swing.
- Manual Tilt: The fan head can be manually tilted up to 30° vertically to direct airflow as desired. Gently adjust the fan head to the preferred angle.
Maintenance and Cleaning
Regular cleaning ensures optimal performance and extends the lifespan of your fan.
- Disconnect Power: Always unplug the fan from the power outlet before cleaning.
- Clean Exterior: Wipe the exterior surfaces of the fan with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Clean Blades and Grills: To clean the fan blades and inside of the grills, carefully remove the front grill and blades (refer to assembly instructions in reverse). Wipe them with a soft, damp cloth. Ensure all parts are completely dry before reassembling.
- Storage: When not in use for extended periods, store the fan in a cool, dry place, preferably in its original packaging.
Troubleshooting
If you encounter issues with your fan, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan does not turn on. | No power supply; remote batteries depleted; fan not properly assembled. | Check power cord connection and wall outlet. Replace remote batteries. Ensure all fan components are correctly assembled. |
| Weak airflow. | Low speed setting; dust accumulation on blades/grills. | Increase fan speed. Clean fan blades and grills as per maintenance instructions. |
| Fan makes unusual noise. | Loose components; obstruction in blades; fan not on a stable surface. | Ensure all parts are securely fastened. Check for any foreign objects. Place fan on a stable, level surface. |
| Remote control not working. | Depleted batteries; obstruction between remote and fan sensor. | Replace remote batteries. Ensure a clear line of sight to the fan's sensor. |
If the problem persists after attempting these solutions, please contact atomberg customer support.
Specifications
| Brand | atomberg |
| Model Name | Renesa Table Fan |
| Colour | Snow White |
| Electric Fan Design | Table Fan |
| Power Source | Corded Electric |
| Product Dimensions (D x W x H) | 60D x 23W x 47H Centimeters |
| Special Features | Inverter Compatible, Remote Controlled |
| Material | Plastic |
| Number Of Speeds | 6 |
| Noise Level | 57 Decibels |
| Wattage | 35 Watts |
| Air Flow Capacity | 76 Cubic Meters Per Minute |
| Speed | 1500 RPM |
| Control Method | Remote |
| Motor Type | Brushless (BLDC) |
| Item Weight | 3.8 Kilograms |
| Country of Origin | India |
Image: Illustration highlighting the energy-efficient BLDC motor and 35% energy savings.
Image: Visual representation of the fan's performance features: 76 CMM air delivery, 57 dB low noise, 1500 RPM speed, and remote operation.
Warranty and Customer Support
Your atomberg Renesa Table Fan comes with a standard 1-year warranty. An additional 1-year warranty can be availed by registering your purchase on the official atomberg website. Please refer to the warranty card included in the box for detailed terms and conditions.
For any queries, technical assistance, or warranty claims, please contact atomberg customer support:
- Email: support@atomberg.com
- Toll-Free Number: 08448449442
- Website: Visit the official atomberg website for more information and registration.
Professional installation services are available at a nominal cost across India. Contact customer support to avail this service.