1. Introduction
Thank you for choosing the Giro Montaro MIPS II helmet. This manual provides essential information for the proper use, care, and maintenance of your helmet. Please read it thoroughly before using your helmet and retain it for future reference. The Montaro MIPS II is designed for mountain biking, offering advanced protection, comfort, and features for an enhanced riding experience.
Image: The Giro Montaro MIPS II helmet, showcasing its matte black finish and distinctive chroma dot design.
2. Safety Information
Your Giro Montaro MIPS II helmet is engineered to reduce the risk of head injury in certain impacts. However, no helmet can protect against all possible impacts. Always ride within your limits and wear appropriate safety gear.
MIPS Technology
This helmet incorporates the Multi-Directional Impact Protection System (MIPS). MIPS is a low-friction layer designed to reduce rotational forces that can result from certain impacts. This layer allows a small relative motion between the helmet and the head in an angled impact, aiming to redirect energy and forces that would otherwise be transmitted to the head.
Image: Detail of the MIPS logo on the helmet, indicating the integrated safety technology.
Helmet Replacement
- After an Impact: A helmet that has sustained an impact should be replaced immediately, even if there is no visible damage. The protective materials may be compromised.
- Age: Helmets should be replaced every three to five years, depending on usage and exposure to elements, as materials can degrade over time.
Warnings
- Do not modify or remove any original components of the helmet.
- Avoid exposing the helmet to extreme heat (e.g., inside a hot car), as this can damage the EPS liner.
- Always secure the chin strap properly before riding.
3. What's in the Box
Your Giro Montaro MIPS II helmet package includes:
- 1 x Giro Montaro MIPS II Bike Helmet
4. Setup: Fitting the Helmet
Proper fit is crucial for helmet safety and comfort. Follow these steps to ensure your Montaro MIPS II helmet fits correctly:
4.1. Adjusting the Roc Loc 5 Air MIPS Fit System
- Place the helmet on your head. It should sit level and cover your forehead.
- Locate the Roc Loc 5 Air dial at the back of the helmet.
- Turn the dial clockwise to tighten the fit system, or counter-clockwise to loosen it, until the helmet feels snug and secure without being uncomfortably tight. The helmet should not move excessively when you shake your head.
Image: The rear of the helmet, highlighting the Roc Loc 5 Air adjustment dial for a personalized fit.
4.2. Adjusting the Chin Straps
- Buckle the chin strap.
- Adjust the sliders on the straps so that they form a 'V' shape just below your ears.
- Tighten the chin strap until it is snug under your chin. You should be able to open your mouth wide, but the strap should not be loose enough to allow the helmet to shift significantly.
4.3. Adjusting the P.O.V. Plus Visor
The Montaro MIPS II features an adjustable P.O.V. Plus visor. This visor can be moved up or down to accommodate goggles or to adjust for sun glare.
- Gently push or pull the visor to the desired position. It will click into place at various detents.
- Ensure the visor is securely in position before riding.
Image: Side profile of the helmet, illustrating the adjustable visor feature.
5. Operating the Helmet
Once your helmet is properly fitted, it is ready for use. Always ensure all adjustments are secure before each ride.
Wearing the Helmet
- The helmet should sit level on your head, with the front edge approximately one inch above your eyebrows.
- The chin strap should be comfortably snug, and the side straps should meet just below your ears.
Ventilation
The Montaro MIPS II features 16 Wind Tunnel vents with internal channeling to provide airflow and keep your head cool during rides.
6. Maintenance
Regular care will extend the life and effectiveness of your helmet.
Cleaning
- Clean the helmet shell and pads with a soft cloth, mild soap, and cool water.
- Do not use harsh chemicals, solvents, or abrasive cleaners, as these can damage the helmet's materials.
- Allow the helmet to air dry completely before storage.
Storage
- Store your helmet in a cool, dry place, away from direct sunlight and extreme temperatures.
- Avoid storing the helmet near heat sources or chemicals.
Inspection
- Periodically inspect your helmet for any signs of damage, such as cracks in the shell or foam, frayed straps, or malfunctioning buckles.
- If any damage is found, replace the helmet immediately.
7. Troubleshooting
If you encounter issues with your helmet, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Helmet feels loose or shifts on head | Improper fit system adjustment or loose chin strap. | Tighten the Roc Loc 5 Air dial and/or adjust chin straps for a snug fit. Refer to Section 4. |
| Discomfort or pressure points | Fit system too tight or incorrect helmet size. | Loosen the Roc Loc 5 Air dial. Ensure you have the correct helmet size for your head circumference. |
| Visor does not stay in position | Visor adjustment mechanism may be loose or damaged. | Ensure the visor is clicked into one of its detent positions. If the issue persists, contact customer support. |
| Excessive sweating | High temperatures or insufficient airflow. | Ensure helmet is positioned correctly to maximize airflow through vents. Consider wearing a sweat-wicking headband. |
8. Specifications
Detailed specifications for the Giro Montaro MIPS II helmet:
- Brand: Giro
- Model Name: Montaro MIPS II
- Model Number: 7140856
- UPC/GTIN: 768686477409
- Outer Material: Polycarbonate (PC)
- Inner Material: Expanded Polystyrene (EPS)
- Item Weight: Approximately 16 ounces (454 grams)
- Item Dimensions: 14 x 10 x 8 inches (approximate, for Small size)
- Special Feature: MIPS Technology
- Ventilation: 16 Wind Tunnel vents with internal channeling
- Visor: Adjustable P.O.V. Plus Visor
- Fit System: Roc Loc 5 Air MIPS
- Recommended Uses: Cycling (Mountain Biking)
- Included Components: Bike Helmet
9. Warranty and Support
Warranty Information
The Giro Montaro MIPS II helmet comes with a 2-Year Manufacturer Warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
Customer Support
For any questions, concerns, or warranty claims, please contact Giro customer support through their official website or the retailer where the helmet was purchased. Provide your model name and proof of purchase for efficient assistance.