Real HD HIK-IK-6284TH-MH/P

Download PDF
Contents

User Manual for HiLook Series Security Camera System

Model: IK-6284TH-MH/P

Brand: Real HD

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your HiLook Series Security Camera System. This system includes an 8-channel 4K 8MP NVR with a pre-installed 2TB hard drive and six 4MP outdoor turret PoE dome cameras. Designed for reliable surveillance, this system offers high-resolution video capture and remote access capabilities.

HiLook Series Security Camera System with NVR and six turret cameras

Figure 1.1: HiLook Series Security Camera System (NVR and 6 Cameras)

2. Safety Information

  • Read all instructions carefully before installation and operation.
  • Use only power adapters specified for this device.
  • Ensure proper ventilation for the NVR to prevent overheating.
  • Do not expose the NVR to water or moisture.
  • Installation should be performed by qualified personnel, especially for outdoor camera mounting.
  • Disconnect power before performing any maintenance.
  • Protect cables from damage and ensure they are properly secured.

3. Package Contents

Verify that all items are present in your package:

  • 1 x 8-Channel 4K 8MP PoE NVR (with pre-installed 2TB HDD)
  • 6 x 4MP Outdoor Turret PoE Dome Cameras
  • 1 x Power Adapter for NVR
  • 1 x USB Mouse
  • 1 x Ethernet Cable (for NVR network connection)
  • Mounting Screws and Plugs for Cameras
  • Quick Start Guide
  • Note: Camera connection cables (Ethernet) are not included and must be purchased separately.

4. Product Overview

4.1 Network Video Recorder (NVR)

The NVR is the central recording and management unit for your security system. It features 8 PoE ports for direct camera connection and power, eliminating the need for separate power supplies for each camera.

NVR Physical Interface Diagram

Figure 4.1: NVR Rear Panel Physical Interface

Table 4.1: NVR Interface Description
No.DescriptionNo.Description
1PoE Interfaces6VGA Output (DB9 Connector)
2LAN Interface7USB Interface
3AUDIO OUT8Power Supply
4AUDIO IN9GND
5HDMI Interface10Power Switch

4.2 PoE Turret Dome Cameras

The 4MP PoE turret cameras provide high-definition video with enhanced low-light capabilities and a wide viewing angle. They are IP67 rated for outdoor use, ensuring durability in various weather conditions.

IPC-T240H 4MP Fixed Turret Network Camera Features

Figure 4.2: IPC-T240H Camera Features

IPC-T240H Camera Dimensions

Figure 4.3: IPC-T240H Camera Dimensions (Unit: mm (inch))

5. Setup

5.1 NVR Initial Setup

  1. Connect the NVR to a monitor using an HDMI or VGA cable.
  2. Connect the included USB mouse to a USB port on the NVR.
  3. Connect the NVR to your network router using an Ethernet cable (LAN interface).
  4. Connect the NVR power adapter to the NVR and then to a power outlet.
  5. Power on the NVR using the power switch.
  6. Follow the on-screen prompts to complete the initial setup wizard, including setting up a password and network settings.

5.2 Camera Installation

  1. Choose suitable locations for your cameras, considering coverage area and cable routing.
  2. Mount the cameras securely using the provided screws and plugs.
  3. Connect each camera to an available PoE interface on the NVR using an Ethernet cable (not included). The NVR will automatically power the cameras and establish a connection.
  4. Adjust the camera angle and focus as needed for optimal viewing.

5.3 Network Configuration (Optional)

The NVR typically obtains an IP address automatically via DHCP. If manual configuration is required:

  • Access the NVR's main menu, navigate to Configuration > Network.
  • Set the IP address, subnet mask, gateway, and DNS server manually.
  • Ensure the NVR's network settings are compatible with your local network.

6. Operating

6.1 Live View

After successful setup, the NVR will display live video feeds from all connected cameras on the monitor. You can switch between single-camera view, multi-camera grid view, and customize display layouts.

6.2 Playback

To review recorded footage:

  1. From the main menu, select Playback.
  2. Choose the camera(s) and date/time range you wish to review.
  3. Use the timeline to navigate through recordings.

6.3 Recording Settings

The NVR supports continuous, motion-detection, and scheduled recording modes. Configure these settings via Configuration > Record.

  • Continuous Recording: Records 24/7.
  • Motion Detection: Records only when motion is detected in the camera's view.
  • Scheduled Recording: Records during specified time intervals.

6.4 Remote Access (Hik-Connect App)

For remote viewing and management:

  1. Download the "Hik-Connect" app from your smartphone's app store.
  2. Create an account and log in.
  3. Scan the QR code displayed on the NVR's monitor (usually found in Configuration > Network > Platform Access) to add your device.
  4. Follow the app's instructions to complete the setup and access live view and playback remotely.

7. Maintenance

  • Cleaning: Regularly clean camera lenses with a soft, dry cloth. For the NVR, ensure vents are free from dust.
  • Firmware Updates: Check the manufacturer's website periodically for firmware updates to ensure optimal performance and security. Follow the provided instructions carefully for any updates.
  • Hard Drive Management: The 2TB HDD will automatically overwrite older footage when full. If you require longer retention, consider backing up important footage or upgrading the HDD capacity (NVR supports up to 8TB per SATA interface).
  • System Health Check: Periodically check the NVR's system logs for any errors or warnings.

8. Troubleshooting

Table 8.1: Common Troubleshooting Steps
ProblemPossible CauseSolution
No video from cameraLoose cable, no power, IP conflict, faulty camera/port.Check Ethernet cable connection. Ensure NVR PoE port is active. Verify camera status in NVR settings. Try a different PoE port.
NVR offline in Hik-Connect appNo internet connection, incorrect network settings, platform access disabled.Check NVR's internet connection. Verify network settings (DHCP/Static IP). Ensure Platform Access is enabled and status is "Online".
Cannot access NVR via browserIncorrect IP address, network firewall, NVR web service disabled.Verify NVR's IP address. Check firewall settings on your PC and router. Ensure HTTP/HTTPS ports are open.
Poor image qualityDirty lens, improper focus, low light conditions, network bandwidth issues.Clean camera lens. Adjust camera focus. Ensure adequate lighting for night vision. Check network bandwidth.

9. Specifications

9.1 NVR Specifications (Model: IK-6284TH-MH/P)

NVR Specification Part 1

Figure 9.1: NVR Specification (Part 1)

NVR Specification Part 2 and Dimensions

Figure 9.2: NVR Specification (Part 2) and Dimensions

Table 9.1: Key NVR Specifications
FeatureDetail
Human/Vehicle Analysis4-ch
IP Video Input8-ch
Incoming Bandwidth80 Mbps
Outgoing Bandwidth80 Mbps
HDMI Output1-ch, 4K (4096 x 2160)/30 Hz, 4K (3840 x 2160)/30 Hz, 2K (2560 x 1440)/60 Hz, 1920 x 1080/60 Hz, 1600 x 1200/60 Hz, 1280 x 1024/60 Hz, 1280 x 720/60 Hz
VGA Output1-ch, 1920 x 1080/60 Hz, 1280 x 1024/60 Hz, 1280 x 720/60 Hz
Video Output ModeHDMI/VGA simultaneous output
Audio Output1-ch, RCA (Linear, 1 KΩ)
Two-Way Audio1-ch, RCA (2.0 Vp-p, 1 K Ω)
Decoding FormatH.265+, H.265, H.264+, H.264
Recording Resolution8 MP/6 MP/5 MP/4 MP/3 MP/1080p/UXGA /720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF
Synchronous Playback8-ch
Decoding Capability1-ch@8 MP (30 fps)/3-ch@4 MP (30 fps)/6-ch@1080p (30 fps)
Stream TypeVideo, Video & Audio
Audio CompressionG.711ulaw/G.711alaw/G.722/G.726
Remote Connection32
Network ProtocolTCP/IP, DHCP, IPv4, IPv6, DNS, DDNS, NTP, RTSP, SADP, SMTP, SNMP, NFS, iSCSI, UPnP™, HTTP, HTTPS
Network Interface1, RJ-45 10/100 Mbps self-adaptive Ethernet interface
PoE Interface8, RJ-45 10/100 Mbps self-adaptive Ethernet interface
PoE Power≤ 80 W
PoE StandardIEEE 802.3 af/at
SATA Interfaces2 SATA interfaces
SATA CapacityUp to 8 TB capacity for each disk
USB Interface2 x USB 2.0
Power Supply48 VDC, 2.5 A
Consumption≤ 15 W (without HDD and PoE off)
Working Temperature-10 °C to 55 °C (14 °F to 131 °F)
Working Humidity10% to 90%
Chassis1U chassis
Dimension (W × D × H)385 × 315 × 52 mm (15.2" × 12.4" × 2.0")
Weight≤ 2.6 kg (without HDD, 5.7 lb.)
CertificationFCC Part 15 Subpart B, ANSI C63.4-2014; CE EN 55032: 2015, EN 61000-3-2, EN 61000-3-3, EN 50130-4, EN 55035: 2017

9.2 Camera Specifications (IPC-T240H)

Table 9.2: Key Camera Specifications
FeatureDetail
Image Sensor1/3" Progressive Scan CMOS
Max. ResolutionUp to 2560 x 1440 (4MP)
Lens2.8mm Fixed Lens
IR RangeUp to 100 ft (30 m) EXIR 2.0 IR Range
Video CompressionH.265+/H.265/H.264+/H.264/MJPEG
WDRTrue 120 dB WDR
Ingress ProtectionIP67 Protection
Housing MaterialDurable Metal Housing
Viewing Angle102° (diagonal)

9.3 General Product Specifications

Table 9.3: General System Specifications
FeatureDetail
Connectivity TechnologyWired
Number of Channels8
Memory Storage Capacity2 TB (Pre-installed)
ColorWhite
Power SourceCorded Electric
Item dimensions L x W x H20 x 13 x 10 inches (System Packaging)
Recommended Uses For ProductIndoor/Outdoor
Compatible DevicesNVR
Signal FormatDigital
Low light technologyNight Vision
Night Vision Range100 Feet (Camera)
Frame Rate30 FPS
Recording ModeContinuous 4K video
Optical Sensor TechnologyCMOS
Hardware InterfaceEthernet
ManufacturerReal HD
Item Weight40 pounds (System)

10. Warranty and Support

For warranty information and technical support, please refer to the warranty card included with your product or visit the official Real HD website. You can also contact customer support through the details provided on the product packaging or the seller's store page on Amazon.

  • Online Support: Visit the Real HD Store on Amazon for product information and support resources.
  • Protection Plans: Additional protection plans may be available for purchase to extend coverage beyond the standard warranty.

© 2025 Real HD. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.