1. Introduction
Thank you for choosing the AZZA CSAZ-1002 Cube Plus ATX Computer Case. This innovative case is designed to provide exceptional aesthetics and performance for your gaming or high-performance PC build. Featuring a unique cube design with wraparound tempered glass panels and pre-installed digital RGB fans, it offers both stunning visuals and efficient cooling. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your new computer case.
2. Key Features
- Stunning Wraparound Glass Design: Features three removable tempered glass panels for a panoramic view of your components.
- Pre-installed HURRICANE III Digital RGB Fans: Equipped with six high-performance digital RGB fans for optimal airflow and customizable lighting.
- AZZA Hub Included: Simplifies fan and RGB lighting control.
- Spacious Interior: Supports ATX and Micro ATX motherboards, multiple storage drives, and large graphics cards.
- Efficient Cooling: Designed for superior airflow to keep your components cool.
Figure 2.1: The AZZA Cube Plus case showcasing its unique cube shape and illuminated fans.
Figure 2.2: Illustration of the removable tempered glass panel mechanism, allowing easy access to internal components.
Figure 2.3: Airflow diagram demonstrating the efficient cooling design of the case, with air intake and exhaust paths.
3. Setup Guide
3.1 Unpacking and Inspection
- Carefully remove the case from its packaging.
- Inspect the case for any signs of damage during transit. If damage is found, contact your retailer immediately.
- Verify all accessories listed in the package contents are present.
3.2 Component Installation
Before installing components, ensure the case is placed on a stable, flat surface.
- Motherboard Installation: Remove the side panel. Install the I/O shield into the motherboard tray opening. Align your ATX or Micro ATX motherboard with the standoffs and secure it with screws.
- Power Supply Unit (PSU) Installation: The PSU mounts at the rear of the case. Slide your PSU into the designated bay and secure it with screws from the outside.
- Storage Drive Installation: The case supports 3.5" and 2.5" drives. Locate the drive bays and secure your SSDs/HDDs using the provided mounting hardware.
- Graphics Card (GPU) and Expansion Card Installation: Remove the necessary PCIe slot covers. Insert your graphics card and other expansion cards into the motherboard's PCIe slots and secure them with screws.
- Cable Management: Utilize the cable routing cutouts and tie-down points behind the motherboard tray to manage cables for improved airflow and aesthetics.
Figure 3.1: Illustration of the rear-mount power supply unit (PSU) installation area.
Figure 3.2: Diagram indicating the flexible mounting options for 3.5-inch and 2.5-inch storage drives.
4. Operating Instructions
4.1 Powering On
Once all components are installed and cables are connected, close the side panels. Connect the power cable to your PSU and a wall outlet. Press the power button located on the case's front I/O panel to power on your system.
4.2 RGB Lighting Control (AZZA Hub)
The pre-installed HURRICANE III Digital RGB fans are connected to an AZZA Hub. This hub allows for synchronized RGB lighting effects. Refer to your motherboard's software for advanced RGB control if it supports addressable RGB synchronization, or use the case's reset/LED switch to cycle through pre-set lighting modes.
Figure 4.1: Wiring diagram for the AZZA Hub, showing connections for PWM fans, Addressable RGB, SATA power, and the reset/LED switch.
5. Maintenance
Regular maintenance ensures optimal performance and longevity of your AZZA Cube Plus case.
- Dust Cleaning: Periodically clean dust filters and internal components using compressed air. Ensure the system is powered off and unplugged before cleaning.
- Glass Panel Care: Clean tempered glass panels with a soft, lint-free cloth and a non-abrasive glass cleaner. Avoid harsh chemicals that may damage the surface.
- Fan Maintenance: Check fans for dust buildup and ensure they are spinning freely. Clean fan blades gently if necessary.
6. Troubleshooting
This section addresses common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| System does not power on. | Loose power connections, faulty PSU, front panel connector issue. | Check all power cables (PSU, motherboard, components). Ensure front panel power switch connector is correctly seated on the motherboard. Test PSU if possible. |
| Fans are not spinning or RGB is not working. | Loose fan/RGB connections, AZZA Hub not powered, software issue. | Verify all fan and RGB cables are securely connected to the AZZA Hub and the hub is receiving SATA power. Check motherboard RGB software settings. |
| Poor airflow or overheating. | Dust buildup, incorrect fan orientation, blocked vents. | Clean dust filters and fans. Ensure fans are oriented correctly for optimal intake/exhaust. Check for any obstructions to airflow. |
7. Specifications
| Feature | Specification |
|---|---|
| Model Name | Cube Plus |
| Item Model Number | CSAZ-1002 |
| Case Type | Mid Tower |
| Motherboard Compatibility | Micro ATX, ATX |
| Material | Tempered Glass |
| Product Dimensions (LxWxH) | 27.1 x 24.6 x 28.4 inches (68.8 x 62.5 x 72.1 cm) |
| Item Weight | 27.5 pounds (12.5 kg) |
| Number of USB 3.0 Ports | 2 |
| Cooling Method | Fan |
| Power Supply Mounting Type | Rear Mount |
8. Warranty and Support
AZZA products are manufactured to the highest quality standards. For warranty information and technical support, please visit the official AZZA website or contact their customer service department. Keep your proof of purchase for warranty claims.
AZZA Official Website: www.azza.com
