Introduction
Thank you for purchasing the ET2 Loom E20982-BK LED Pendant Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.
Important Safety Information
To reduce the risk of fire, electric shock, or personal injury, always follow these basic precautions:
- WARNING: Disconnect power at the circuit breaker or fuse box before installation or servicing.
- All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC).
- Consult a qualified electrician if you are unsure about the installation process.
- Do not install this fixture in wet locations. It is designed for indoor use only.
- Handle the fixture with care. Avoid dropping or subjecting it to strong impacts.
- Do not attempt to modify the fixture or its components.
- Ensure the mounting surface can support the weight of the fixture.
Setup and Installation
This pendant light requires assembly and ceiling mounting. Professional installation is recommended.
Tools Required:
- Screwdriver (Phillips and Flathead)
- Wire Strippers
- Electrical Tape
- Ladder
- Voltage Tester
Installation Steps:
- Turn Off Power: Locate the circuit breaker controlling the light fixture's power supply and turn it off. Verify power is off using a voltage tester.
- Prepare Mounting Surface: Ensure the junction box is securely mounted to the ceiling and can support the fixture's weight.
- Assemble Fixture: Carefully unpack all components. Follow the specific assembly instructions provided in the packaging for your model. This typically involves attaching the pendant rings and cotton strands.
- Wire Connections:
- Connect the fixture's ground wire (usually bare copper or green) to the house ground wire.
- Connect the fixture's neutral wire (usually white) to the house neutral wire (white).
- Connect the fixture's hot wire (usually black) to the house hot wire (black).
- Secure all connections with wire nuts and electrical tape.
- Mount Fixture: Carefully lift the fixture and attach the canopy to the junction box using the provided screws. Ensure all wires are tucked neatly into the junction box.
- Adjust Height: Adjust the suspension cables to achieve the desired pendant height. Secure the cables according to the fixture's design.
- Restore Power: Once installation is complete and all connections are secure, restore power at the circuit breaker and test the light.
Figure 1: Front view of the ET2 Loom E20982-BK LED Pendant Light, showcasing its unique design with cross-threaded cotton strands and illuminated rings.
Operating Instructions
The ET2 Loom E20982-BK LED Pendant Light is designed for simple operation.
- Power On/Off: Control the light fixture using a standard wall switch connected to the circuit.
- LED Technology: This fixture uses integrated LED light sources, which are highly efficient and long-lasting. There are no bulbs to replace.
- Dimming: If connected to a compatible LED dimmer switch, the light output can be adjusted. Consult a qualified electrician for dimmer compatibility and installation.
Figure 2: The ET2 Loom E20982-BK LED Pendant Light illuminating a contemporary room, demonstrating its aesthetic and functional presence.
Care and Maintenance
Proper care will ensure the longevity and appearance of your ET2 Loom pendant light.
- Cleaning: Always turn off power before cleaning. Use a soft, dry, or slightly damp cloth to wipe the exterior surfaces. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish or LED components.
- LED Care: The integrated LED light sources do not require replacement. If an LED component fails, contact customer support for assistance.
- Inspection: Periodically check for any loose connections or damage to the fixture. If any issues are found, disconnect power and consult a qualified electrician or customer support.
Troubleshooting
If you experience issues with your pendant light, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. |
|
|
| Light flickers or dims unexpectedly. |
|
|
| Fixture makes humming noise. |
|
|
If these solutions do not resolve the issue, please contact ET2 customer support.
Product Specifications
| Brand | ET2 |
| Model Name | E20982-BK (Loom) |
| Product Dimensions | 18.75"L x 18.75"W x 15"H |
| Item Weight | 4.4 Pounds |
| Material | Aluminum, PVC, Steel |
| Color/Finish | Black |
| Light Source Type | Integrated LED |
| Number of Light Sources | 2 |
| Wattage | 21 Watts (total) |
| Voltage | 120 Volts |
| Room Type | Living Room (also suitable for dining areas, bedrooms) |
| Indoor/Outdoor Usage | Indoor |
| Assembly Required | Yes |
| Mounting Type | Ceiling Mount |
| UPC | 783209321472 |
Warranty Information
The ET2 Loom E20982-BK LED Pendant Light comes with a Limited Warranty. For specific terms, conditions, and duration of the warranty, please refer to the warranty card included with your product packaging or visit the official ET2 website. Retain your proof of purchase for any warranty claims.
Customer Support
If you have any questions, require technical assistance, or need to report a problem with your ET2 Loom E20982-BK LED Pendant Light, please contact ET2 customer support. You can typically find contact information on the manufacturer's website or in your product documentation.
For more information, visit the official ET2 website: www.et2lighting.com
